I know this is a legacy product, but was wondering if the following could be clarified...

The manual states that the Transition Level should be set in the DES FORECASTS page of the FMC. However it appears that the Transition Level call during descent takes it's value from the Transition Altitude value in the PERF INIT page instead. Is this correct?

I did see a very old post suggesting the correct value couldn't be read from the aircraft (iFly SDK limitation?), but was wondering if this was still the case for the final version? The workaround suggested was to change the PERF INIT page value mid-flight, but I don't believe that page is accessible once in the air.

This is for P3Dv4.5 using the iFly 737NG and FS2Crew Voice.

Many thanks

Phil

now that I am going to be using UGCX I set up the key d to

trigger the Hard Mute but it's not turning the Hard Mute on

Any solutions are greatly appreciated

Current Task: Creating the Critical Section Object..., SUCCEEDED!
[Unknown Operating System]
Microsoft Flight Simulator X
Current Task: Creating the ISpRecognizer object..., SUCCEEDED!
Microsoft Speech Recognizer 8.0 for Windows (English - UK)
Current Task: Creating the ISpRecoContext object..., SUCCEEDED!
Current Task: Setting the CallBack Function..., SUCCEEDED!
Current Task: Setting the Notifications Interest..., SUCCEEDED!
Current Task: Creating the ISpAudio object..., SUCCEEDED!
Current Task: Setting the Audio Input..., SUCCEEDED!
Current Task: Setting the Recognizer State..., SUCCEEDED!
Current Task: Creating the ISpRecoGrammar object..., SUCCEEDED!
, Error Code: 0x80045052
Many thanks  for any suggestions

Michael Quick

After purchasing bundle package FS2Crew iFly, version 1.2 (8 July 2011), I installed the version Voice in my FS9.
Then I installed the update version 2.3.
These are my flight system requirements: Intel Core i7-920 (4 x 2.666 GHz) - 6144 MB RAM with a graphics card: 2 x XFX Nvidia Geforce GTX 295 (1792MB), Windows XP 64bit (gaming edition), Flight Simulator 9.1, iFly 737 version 3.2.2
Before starting my FS9 I first started the iFly config tool and for all aircraft models enabled the voice.
At the 1st flight I was doing all right with a CTD at approach of an airport, with the popup message out of memory.
This should not really happen with 6GB of RAM in my system.
At the 3rd flight I was tired and did the whole program of FS2Crew have taken off again, I again installed the version 1.2 and 2.2 after reboot.
Unfortunately again after two flights, the CTD issue.
Again, remove the entire program and FS2Crew installed after a restart now only the version 1.2.
This might not benefit directly in my 1st flight again a CTD.
Meanwhile, remove all of FS2Crew and now after 3 flights fly no more problems with the CTD issue.

Now I ask myself what is wrong and I quite regret that I have made this purchase.
Hopefully someone from the team develepment FS2Crew something to tell what is wrong with this software in FS9.

Regards,
John

My home cockpit : http://www.john1604.nl

I know my microphone is working as I am able to communicate on Vpilot and the Voice Control option is set in the iFly config manager.

FO still prepares flight deck in preflight (when PF button pushed) and announces "Cabin Secure" before takeoff, "10,000 '" and "Transition altitude" and he just announced "Center fuel pumps going off".  He just ignores me.

I noticed that on the -700 the FO is setting the Engine Start Switches to CONTINIOUS for T/O (before Taxi) and for landing (as I think is the correct way to do).

On the -800 he is setting the Engine Start Switches to AUTO for T/O and LDG

He also doesnt correct me if i read back "Continous" even if Auto is selected

Are there different procedures between -700 and 800, or is this a bug?

I did some searching and I think it should be on CONT on all models?!

Win7-64 pro, FS9.1, Ifly 3.2.something, FS2CrewVoice latest update

thanks

Stefan

First of all, what a nice product FS2Crew, it takes some time to learn, but now, i cant fly without. I'm using it nearly a year without problems.

This week foor the first time a flight from EBBR (Brussels) to EHAM (Amsterdam) start descending, FSX freezes without saying why, a second time, a third time, problem persists!

Using latest version 2.3 voice.... but, i happens the moment you say descent cheklist. I just just skipped this item and went direct to Approach cheklist....found it! Everything works normal.

Found on the net that it could be that de airport is very low, indeed Amsterdam EHAM 13 feet. The readback of the FO provokes the crash of FSX!!

Is there a solution to this problem ?, it's not elegant to skip the descent item...

Thank You!!

Ivan Werbrouck

I would like to know if the Ifly 737ng fs2crew works in p3d 2.5. I have used the well known fsx to p3d migraton tool with other addons in the past. I would love to use fs2crew.

thx Lee

I fly on Vatsim and I use vPilot to connect to their servers. I just downloaded the iFly 737NG Series as well. I have not flown the 737NG on Vatsim yet because I have been learning the FMC and Nav operations. When I used any other plane (CRJ700) on Vatsim and connected with vPilot I didn't have any communication problems thru my microphone, the controllers heard me clearly.

I installed FS2Crew for less workload in the 737NG (Which is Awesome BTW!!). FS2Crew works fine by itself and the speech recognition works great and recognizes me clearly when I speak. I have been using Speech Recognition for other games as well for about a year now so I know that is setup properly.

When I run vPilot and FS2Crew together, FS2Crew does not recognize my voice AT ALL while vPilot is running. If I close vPilot, then FS2Crew works again after I close FSX completely and reload without vPilot. This is frustrating because I need vPilot to connect to Vatsim.

I am not sure if there is a setting checked wrong or if they conflict with eachother but they will not work together period!

Someone please help me troubleshoot this. I am extremely computer savvy so geek talk will work with me. :smile:

I tried using FSInn but when I start that program it freezes my Simulator so thats why I went with vPilot. Is there a suggestion for a different program for Vatsim that doesn't conflict with FS2Crew?

Any help is appreciated!!

NOTAM:

22 January 2014

Version 2+ of FS2Crew for the iFly 737 NGX is ready!

Important:

THIS UPDATE IS NOT BUILT INTO THE MAIN INSTALLER.

THE INFORMATION IN THIS THREAD SUPERCEDES ANY ASSOCIATED INFORMATION IN THE MAIN OPS PDF MANUAL (ESPECIALLY WITH RESPECT TO 'BUTTON VERSION' JOYSTICK AND KEYBOARD ASSIGNMENTS). 

Download link:

http://fs2crew.com/cart/Updates/FS2CrewIFlyV2.zip

Change Log Version 2.4 (FSX Button Control Only):

1. Updates the FSX Button Control only.  Corrects problem associated with pre-flight sounds playing during Securing flow.

Change Log Version 2.3:

1. Updates the FSX version only.  The FS9 version does not require updating.

2. On-line Google MAP functionality removed since it interfered with the BBJ models and caused erratic behavior.

3. Countdown timer display now visible again on the Main Panel.

Change Log Version 2.2A:

1. Updates the FSX/FS9 Button Control versions only.  Fixes an issue associated with below Sea Level Airports which would produce a CTD when the Descent Checklist was read back.

Change Log Version 2.2:

1. FA Cabin announcements restored.

Change Log Version 2.1:

1. The Green Bar in the FSX Voice version control is now working again.

2. A couple other minor bug fixes.  

Change Log Version 2.0:

1. FS2Crew iFly is now compatible with the iFly Features Pack (RTO during After Takeoff Flow and the Trans Alt/Level button on the FO's side).

2. FSX Voice Control Version only:  You can now view yourself on FS2Crew's on-line Map:  

http://fs2.fs2crew.com:8080/SimpleTracker/map.do

3. Video Marshaller now works in Windows 8.

4. The product should now function in Prepar 3D.  Note that the FS2Crew installer does not support P3D.  You will need to manually move the FS2Crew files and folder to P3D.

5. Numerous code improvements.  You should no longer experience any volume changes when you switch views.

6. BBJ Models:  After Landing flow will no longer trigger the TCAS test.

7. After Landing flow:  FO will turn on taxi light prior to turning off landing lights.

8. New "Soft Mute" assignment system.  You now need to assign a key or joystick button to "PROP SYNC" for Soft Mute (same assignment as used in the NGX).

9. For "Button Control" users, the key assignments for the Main and Secondary Button have been updated to match those used in FS2Crew NGX:

MAIN BUTTON:

ALTERNATE STATIC SOURCE ON/OFF

SECONDARY BUTTON:

PROPELLER SYNC ON/OFF

10. You can now toggle open/close the FS2Crew Main Panel using this assignment:

AUTOFEATHER ARM/OFF

I enjoy the Voice Control version a lot and I think it is a brilliant add-on.

But I have problems getting the voice recognition to understand specific words,

Whenever I say 'OK', it is interpreted as 'open'. I have tried many pronounciations, but always the same. It never understands 'OK'.

I also have problems with 'You're cleared to disconnect and go to hand signals'.

I have gone through the setup and voice training several times, and on two different PC's but it does not help.

Any suggestions ?

Peter

Tried posting this in the Botton control forum but got no reponse

I have the button control version I bought for FS9 version of IFly 737. Will this work on the FSX version if I install it?

Thanks

Stephen

Is there a proper tutorial showing the user the complete procedure from start to finish - together with Actions and Voice Commands relevant to those actions... in the correct order ?

Heck, I can't even find a decent one on Youtube !

Even the older button versions had decent tutorials - such as the ATR for example.

I realise that all the checklists and voice commands are actually in the "manual", but it is fragmented and hardly constitutes a "Tutorial". One starts on Page 43 for actions, then down to page 50-odd to see what the FO actions are... then to Page 60-odd to find the relevant voice commands, then back to Page 44, for the next actions, and down again to page 50-odd for the FO actions, and then to page 60 for the voice.... blah blah and so on.

Franlky I'd rather stick pins in my eyes than try to use this "Tutorial" in its present form.

We all know 90%+ of forum posts are from those of us having some sort of difficulty. I'm wondering how many who lurk here have had absolutely no problems with installation and/or the UI and would truly miss FS2Crew if it... were gone. I'm beginning a home cockpit build that'll be based with the iFly B737 and would love to include FS2Crew!

I'm looking for positive feedback. Looks like one heck of a breakthrough here!

Tkx!

Doug

I have the problem where my FSX gives a CTD when decending into EHRD. It happens at the moment, when I have called for the decent checlist, and it wants to read the Landing altitude.

EHRD is below sealevel, but so is EHAM. But it doesn't crash when I arrive into EHAM.

I have installed the latest 2.2a update.

It is I, pain number 1, I was recently given a FS2Crew disc for FS9 for the iFly 737NG, I am operating XP and FS2004 on an elderly laptop, I loaded the FS2crew and then updated it to the new version V2 (was that a mistake?) then I installed SAPI which I obtained from the microsoft website, great, I started FS9 and loaded IFly737 in windowed mode (which I hate!) and then checked in the FS9/views menu all the panels all are there and all work except the main control panel which causes black screen, then after a pause FS9 crashes and a message appears inviting me to report the failure, the same thing happens if I click on the centre of the Stby. horizon.

I've just found a post outlining a similar problem to mine, the solution being to rt click on the config manager and run it as admin, I did look at this but when I rt click on the icon I am not given the "run as admin" option. 

I was very unsure whether to post here or in the CTD forum, my abject apologies if I put this in the wrong place.

Any ideas anybody, my thanks in advance.

mog

Any help would be much appreciated

 regards

 Brian

I'm upgrade iFly to version 3.2 and when i'm starting Fs2Crew the software is crash with error:

Invalid XGS Patch.
Please contact FS2Crew.
Error code 0x80070057

I'm trying reinstall Fs2Crew but this not work :(

Please help

- Piotr.

can you help. thank you

I just installed iFly 737 and got the FS2Crew too, I run it on P3D.

I have installed and set-up like instructed (running config tool as admin etc)

First the mouse pointer doesn't become a hand when I run it over standby horizon (digitial layout)

but I can click anyway, but every time sofar P3D crashes. iFly it self works and it's only when

I load Fs2Crew.

In event viewer I get this message: