Jump to content
Sign in to follow this  
Guest Cyber Air 062

fmc OAT entries

Recommended Posts

Guest Cyber Air 062

Hi, Im having a little difficulty here with the 800-900 upgrade since I have intalled it.In the section of the FMC where you enter OAT I cannot seem to enter any number below 20'c. If the temperature outside is 08 then how do I enter it please. The fmc says invalid entry yet its displayed like so __//15'c.RegardsDavid Bowen

Share this post


Link to post

You can enter /08 or if needed /-XX as valid formats. [h4]Best Wishes,Randy J. Smithhttp://www.precisionmanuals.com/images/forum/betaimg.jpgAMD 64 3200+ | ASUS KV8 DELUXE | GFORCE 5700 ULTRA @535/1000 | Maxtor 6Y080M0 SATA 80 GIG | 512 DDR 400 | Windows Xp Pro | Windows Xp Pro 64 |

Share this post


Link to post
Guest Cyber Air 062

Hi, I have been trying this a few times. I have had the PMDG planes since they came out so I dont think im doing anything wrong or different to before im just simply trying to enter the temperature in 'c. I have tried all cominations and nothing works. The lowest I can enter is 16. When I enter 08 or 008 the fmc says invalid entry.RegardsDavid

Share this post


Link to post

Hi guys,Same problem here. 16 is the lowest I can enter. Any lower value will result in an invalid entry. Thanks for help!RegardsMark


Mark van Wissen

Share this post


Link to post

Are you guys running the 1.4 patch? 1.4 as in the interm engine fauiler 800-900 patch? I can enter /08 just fine but I do not have that patch installed.[h4]Best Wishes,Randy J. Smithhttp://www.precisionmanuals.com/images/forum/betaimg.jpgAMD 64 3200+ | ASUS KV8 DELUXE | GFORCE 5700 ULTRA @535/1000 | Maxtor 6Y080M0 SATA 80 GIG | 512 DDR 400 | Windows Xp Pro | Windows Xp Pro 64 |

Share this post


Link to post

Hi,In the SEL/OAT on N1 LIMIT page the lowest I can input is 16. I have not installed the patch.According to Mats: "The range has been narrowed to 16 to 70 degrees". Take a look at this post: http://forums.avsim.net/dcboard.php?az=sho...50434&mode=full. The manual still says "Valid entries are one or two digit entries from 0 to 99".So I think the lowest you can input is 16.

Share this post


Link to post
Guest Toni Rauch

Hi CaptainsI asked a very similar question on this forum about a week ago and was given the same solution - i.e. you can only input numbers from 16 upwards on the SEL field.What Randy is referring to is the default-set OAT (15), which can also be changed using the 'slash' key (e.g. /17 etc).The explanation I was given is that the '15' is the (assumed) temperature for the take-off runway which is normally the same as, or slightly more than the ambient outside temperature. Therefore, the value is rarely changed in the SEL field (as the OAT is 'sensed' by the plane's systems.)Because of this, PMDG restricted the inputs to values higher than the 'default' OAT of 15.A bit confusing I know - maybe PMDG will allow more (lower) input selections in an update.......?Hope this helps.Toni.

Share this post


Link to post

No this is way off here guys based on a missunderstanding.1] The OAT is changable, this is the RIGHT FIELD, not the LEFT FIELD. The left side is for tempt reduction and you always imput a GREATER value, not the actual value. Here on the right I selected 8 just like I stated you could....To further clarify, the SEL is to fool the FMS into thinking the tempt is greater so you use less thrust for TO. It is not meant to update the OAT and IS like the real FMC.http://forums.avsim.net/user_files/77593.jpg[h4]Best Wishes,Randy J. Smithhttp://www.precisionmanuals.com/images/forum/betaimg.jpgAMD 64 3200+ | ASUS KV8 DELUXE | GFORCE 5700 ULTRA @535/1000 | Maxtor 6Y080M0 SATA 80 GIG | 512 DDR 400 | Windows Xp Pro | Windows Xp Pro 64 |

Share this post


Link to post
Guest Cyber Air 062

Hi Randy, Thnaks for your help. I have managed it now. All you have to do is put a /8. I didnt realize that. Thanks for all your help.Best regardsDavid Bowen

Share this post


Link to post
Guest Toni Rauch

Thanks Randy...you learn something new every day.Makes a lot more sense now.Toni.

Share this post


Link to post

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  
  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
×
×
  • Create New...