Jump to content

Sign in to follow this  
Guest

Throttles and pots

Recommended Posts

Guest

I've seen some great posting recently on throttles and how to create resistance. I'm in the design phase of my throttles and I'm wondering if there are any good articles out there that deal with pot range of movement and alignment with throttle travel.In otherwords, when my throttles are pulled back to idle, I want my pots to be aligned at approx zero, and when throttles are full, likewise pots are maxed. Seems to me it's going to be tricky to figure out the exact range of motion and gearing to get them to work.Any of you folks that are already beyond this, if you'd be kind enough to share some wisdom it would be much appreciated.thx.Kevin

Share this post


Link to post
Share on other sites
Guest

I am not sure why you would want to do this since any space left over will be compensated for in the calibration. the best thing to do is to build the yoke, and find out the angle it travels. then get a potmeter that gets closest to that angle.

Share this post


Link to post
Share on other sites

Hi Kevin,It's really not that difficult to calculate the gears.It's not really relevant that you use the full 270 degrees rotation of a normal potmeter. The related resistance swing however, can be important especially when you connect the pots through a USB convertor (since these uses A/D conversion). Try to get a resistance swing of appr. 0 - 100 Kohm, either by using the full rotation of a 100 Kohm pot, or (if you don't use the whole 270 degrees rotation) a higher pot value.About the transmission:Don't use the whole 270 degrees rotation range of a potmeter, but limit it to max. 240 degrees (since the beginning and end of a potmeter resistance taper usually have a small dead zone, or are not lineair there).Now, as suggested above, make you throttle construction first and than calculated the gears you need. Suppose the rotation of the throttle levers is 60 degrees, this means that you should use gears: 240/60 = 4:1 ratio.Cheers, Rob

Share this post


Link to post
Share on other sites

KevinYes they are right, in fact it doesn't matter. But for precision it is the best to use as much of the potrange as possible.I used linear sliding potmeters. I connected them to the levers (spoilers, trust, flaps and trim) via a iron rod. By adjusting the hight were the rod was fixed to the lever (distance from the axis on which the lever turns) I could influence the travel of the pot and use as much as possible.I hope you understand whate I mean.You can see pictures with details on my sitehttp://home.wanadoo.nl/norbert.bosch

Share this post


Link to post
Share on other sites
Guest

Kevin,If you use Epic, it doesnt matter. Epic will read what throws you have available it will then assign a min and max based on what you have available.Mike

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
  • Donation Goals

    AVSIM's 2020 Fundraising Goal

    Donate to our annual general fundraising goal. This donation keeps our doors open and providing you service 24 x 7 x 365. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. We reset this goal every new year for the following year's goal.


    2%
    $540.00 of $25,000.00 Donate Now
×
×
  • Create New...