Jump to content
Sign in to follow this  
helberger

Aerosim L1011 - Wing Views

Recommended Posts

Hello,A few days ago I bought the Aerosim Classic 2 package and I agree with everybody that the L1011 is a fine aircraft. However I can't seem to activate the Wing views after selecting one in the aircraft folder withwing views. I e-mailed Aerosim support, they said that I am not movingback far enough in the cabin. When I do that, then past the flight deckdoor I am outside the aircraft and see the wings detached way behind the flight deck. What am I doing wrong?? I have Active Camera installed.Any ideas??Helmut


My System: Intel 9700K 4.7Gz, ROG Strix Z390-E Gaming, 32 GB Corsair Vengeance 3200MHZ, Evga 3070TI  8GB, Noctua NH-D15S, Gigabyte 27" Monitor, Windows 10 64bit, 2xSamsung 500GB SSD, 1x Samsung 120GB, 1x Samsung 970, 1TB, 1TB H/D for Storage.

 

 

Helmut Berger

Share this post


Link to post
Share on other sites
Guest HeavyFan

hi there helmut! I have made my own wing views for the L-1011! But make sure you have the correct model MDL assigned in the planes CFG file. I found out that the way Aerosim had it, was the MDL's were named wrong. the NoVC was actually the Wing view model, and the Wingviw Model was actually the VC MDL. so just try and check which MDL you are using to get the Wingview Only Model! Ok here's my Settings for the Wing Views, just delete the old "Views" in the CFG file, and Replace with mines! these go into the Panel CFG file.![Views]view_forward_WINDOWS=MAIN_PANELVIEW_FORWARD_DIR=2.0, 0.0, 0.0VIEW_FORWARD_ZOOM=0.6VIEW_FORWARD_RIGHT_WINDOWS=30 ///////////////////VIEW OF RIGHT BACK WING!VIEW_FORWARD_RIGHT_ZOOM=0.8VIEW_FORWARD_RIGHT_EYE=0.0, -1.00, -38.00,VIEW_FORWARD_RIGHT_DIR=0.0, 0.0, 65.0VIEW_RIGHT_WINDOWS=31 //////////RIGHT MAIN WING VIEW!!!!VIEW_RIGHT_ZOOM=0.8VIEW_RIGHT_EYE=0.0, -.70, -28.00,VIEW_RIGHT_DIR=0.0, 0.0, 100.0VIEW_REAR_RIGHT_WINDOWS=32 //////////////RIGHT WING ENGINE VIEW!!!VIEW_REAR_RIGHT_ZOOM=0.9VIEW_REAR_RIGHT_EYE=0.0, -0.50, -11.00,VIEW_REAR_RIGHT_DIR=0.0, 0.0, 120.0VIEW_REAR_WINDOWS=33VIEW_REAR_ZOOM=0.8VIEW_REAR_LEFT_WINDOWS=34 ////////LEFT WING ENGINE VIEW!!!VIEW_REAR_LEFT_ZOOM=0.9VIEW_REAR_LEFT_EYE=0.0, -0.50, -11.00VIEW_REAR_LEFT_DIR=0.0, 0.0, 235.0VIEW_LEFT_WINDOWS=35 /////////////LEFT SIDE MAIN WING VIEW!!VIEW_LEFT_ZOOM=0.8VIEW_LEFT_EYE=0.0, -.70, -28.00VIEW_LEFT_DIR=0.0, 0.0, 260.0VIEW_FORWARD_LEFT_WINDOWS=36 ///////VIEW OF LEFT SIDE BACK WING!VIEW_FORWARD_LEFT_ZOOM=0.8VIEW_FORWARD_LEFT_EYE=0.0, -1.00, -38.00VIEW_FORWARD_LEFT_DIR=0.0, 0.0, 290.0VIEW_DOWN_WINDOWS=37VIEW_DOWN_DIR=15.0, 0.0, 0.0Enjoy MIKE:)

Share this post


Link to post
Share on other sites

Hi Mike,Thank you very much for sending me the wingviews for the L1011, I now have wing views. One question, I checked the panel.cfg for every versioninstalled and all I see is these few lines:[Views]View_Forward_dir=1.5, 0.0, 0.0View_Forward_Zoom=.80.View_Forward_Eye=0.0, 0.0, 0.0Day=255,255,255Night=30,35,35Luminous=250,210,180Is that what they shipped or did I miss anything??Helmut


My System: Intel 9700K 4.7Gz, ROG Strix Z390-E Gaming, 32 GB Corsair Vengeance 3200MHZ, Evga 3070TI  8GB, Noctua NH-D15S, Gigabyte 27" Monitor, Windows 10 64bit, 2xSamsung 500GB SSD, 1x Samsung 120GB, 1x Samsung 970, 1TB, 1TB H/D for Storage.

 

 

Helmut Berger

Share this post


Link to post
Share on other sites

Hello, The VC model is VC only, the Wingview model is VC and wingview, the NoVC model is Wingview only. :)If you have Active camera and are in either the Wing view model or NoVC model....simply move all the way back untill you are above the wing.Wing view does not mean Virtual Cabin ...you will only see the wings and engines.:)

regardsEd

http://forums.avsim.net/user_files/129637.jpgAMD Athlon 64 3500+, 1024Mb PC3200 DDR, 300Gb HD 128Mb DDR Nvidia 6600GT PCI Express, Audigy 2 ZSCH Products Yoke, Pedals and Throttle Quadrant

Share this post


Link to post
Share on other sites
Guest HeavyFan

Your Welcome! Yea that is the way it is from Aerosim, So Just remove the Orginal Views that you saw [Views]View_Forward_dir=1.5, 0.0, 0.0View_Forward_Zoom=.80.View_Forward_Eye=0.0, 0.0, 0.0and replaced them with mine. Also always make Backup copys of the orginal CFG file, Just In case! Ok Enjoy, MIKE:)

Share this post


Link to post
Share on other sites

Thanks for the help, I got my Wing views working fine now.Helmut


My System: Intel 9700K 4.7Gz, ROG Strix Z390-E Gaming, 32 GB Corsair Vengeance 3200MHZ, Evga 3070TI  8GB, Noctua NH-D15S, Gigabyte 27" Monitor, Windows 10 64bit, 2xSamsung 500GB SSD, 1x Samsung 120GB, 1x Samsung 970, 1TB, 1TB H/D for Storage.

 

 

Helmut Berger

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
×
×
  • Create New...