Is there a way to not have the aircraft 'dead' during initializing?

[factory15 0]

Hi-i tried to search on this and had no luck.I've been trying to practice final approaches- hence i'm only around 2-3000 ft when i'm loading the save. And while the aircraft is initializing its basically a 135,000 lb lawn dart.I've notice on some save points that the aircraft seems to glide while loading...and most others (esp the ones i'm interested in) its dead and begins an immediate nose dive. I'm not sure what I did in saving one situation over the other.Is there a way around this?thankssteve deparis

[masneoquil 66]

what if you pause while loading?I'm sorry i never load any plane in the middle of the air.

[bakaman 28]

what if you pause while loading?I'm sorry i never load any plane in the middle of the air.

+1

[factory15 0]

Tried that. Unfortunately it pauses the initialization as well

[idoleo2001 3]

Press "Y" for active slew mode while is loading, after that press "Y" another tiem and ready!

[PIC007 82]

When you save the flight, check the box for the 'default' flight, then the next time you are in it should be the same as you left it.

[factory15 0]

the slew mode looked promising but for some reason after the initialization is complete, there are multiple alarms and a lot of the nav info is gone. I'm not sure how setting it to the default flight changes anything with regards to initialization.i'm surprised more people aren't running into this limitation if they want to practice an approach.

[willywonka 36]

the slew mode looked promising but for some reason after the initialization is complete, there are multiple alarms and a lot of the nav info is gone. I'm not sure how setting it to the default flight changes anything with regards to initialization.i'm surprised more people aren't running into this limitation if they want to practice an approach.

I have! Found it to be too much of a setup problem so I just program and save the flight as ready to take off. Then I just have to fly a pattern to practice landing.

[factory15 0]

I have! Found it to be too much of a setup problem so I just program and save the flight as ready to take off. Then I just have to fly a pattern to practice landing.

i guess i ultimately may do that..or load the save much higher up to give me space to recover....then maybe increase sim rate to get me on final. I just got the saitek yoke and rudder pedals (former joystick user with autorudder set) so right now landing is like a whole new ballgame for me. I just wanted to quickly be able to practice it over and over again.

[Jetman67 517]

yes i have the same issue just need to save a little higher for that few seconds while the Aircraft is initialising

[jordanal 70]

I have noticed this as well but I have been saving situations at cruise or just before ToD. One thing I have learned is that as soon as the initialization bar goes away, make sure your cycle the LNAV and VNAV buttons and it comes back to the path in a pretty short order. I've never tried saving a situation in the descent phase and could easily see how that would be problematic (i.e., heavy lawndart, LOL.. classic...) I too would like to save a IAF/FAF situation to practice the manual landings.Ryan,Is it possible the PMDG devs could look into a way to continue the initialization while the sim is paused? Maybe investigate as a possible item for SP2?

[DrumsArt 270]

I have noticed this as well but I have been saving situations at cruise or just before ToD. One thing I have learned is that as soon as the initialization bar goes away, make sure your cycle the LNAV and VNAV buttons and it comes back to the path in a pretty short order. I've never tried saving a situation in the descent phase and could easily see how that would be problematic (i.e., heavy lawndart, LOL.. classic...) I too would like to save a IAF/FAF situation to practice the manual landings.Ryan,Is it possible the PMDG devs could look into a way to continue the initialization while the sim is paused? Maybe investigate as a possible item for SP2?

+1Regards,Richard Portier

[Smasher77th 13]

+1Regards,Richard Portier

That is how it functioned in the 744/8i. I used to pause and wait until the initialization was complete, and then unpause, and everything was good. I wish they would bring back that feature.