Jump to content

Archived

This topic is now archived and is closed to further replies.

byork

[18 Oct 2019] NGX Reboot 3.4 FOR P3D V4 Released -UGCX Support!

Recommended Posts

Hi Bryan,

 

It appears that the texts of the FSX events we are talking about can be found in the file: FSX/Language.dll.

To find them however you have to insert a hex. '00' value between each ASCII character. E.g. to search for NUMPAD (in hex: '4E 55 4D 50 41 44') you have to search for '4E 00 55 00 4D 00 50 00 41 00 44'.

In this way I found the text of the events I mentioned in my previous reply but the word NITROUS is NOT present in this file.

 

Jaap

Share this post


Link to post
Share on other sites

Hi,

what is with my emergency pack for B737 NGX with all the FO voices? Why must it be installed to use the new update 3.1  737 NGX ? It costs me a lot of Money and now i have to throw it away? Please help me. My English is very bad as you can see. It is only School english and more than 60 years old.

Regards

Peter Timm

Share this post


Link to post
Share on other sites

After the last update my FO (using the Scandinavian soundset) asks to release the crew crew at 10 000ft instead of the passengers.

Share this post


Link to post
Share on other sites

 

 


After the last update my FO (using the Scandinavian soundset) asks to release the crew crew at 10 000ft instead of the passengers.

 

Nothing was changed in that area.  Make sure you're following the manual to the letter.

 

And ensure your units of measurement for altitude in FS are set to "feet", not meters.

 

Cheers,

Share this post


Link to post
Share on other sites
Hello,
 
I have a problem with V 3.1. The installation went well, the recording too. On the other hand, when I run reboot 737 NGX with the 25 minutes. The 25-minute timer counts down to 0 minutes after several hours !!!!! And the procedures during these very very long minutes do not normally bind. Thanks in advance to help me and I do not want to uninstall or install the PMDG 737 NGX while it works without problems and my machine settings are made.
 
cordially
 
 
Eric

To follow up on my previous message, I own p3d V3.4.18.19475
 
Thank you in advance for your help

Share this post


Link to post
Share on other sites

 

Hello,
 
I have a problem with V 3.1. The installation went well, the recording too. On the other hand, when I run reboot 737 NGX with the 25 minutes. The 25-minute timer counts down to 0 minutes after several hours !!!!! And the procedures during these very very long minutes do not normally bind. Thanks in advance to help me and I do not want to uninstall or install the PMDG 737 NGX while it works without problems and my machine settings are made.
 
cordially
 
 
Eric

To follow up on my previous message, I own p3d V3.4.18.19475
 
Thank you in advance for your help

 

 

 

Are you getting the SDK warning?

 

Send me a Ticket at: www.fs2crew.com

 

Thanks,

Share this post


Link to post
Share on other sites
4 hours ago, byork said:

Bump!  V3.2 has been released for P3D v4 owners!

Downloaded and installed for 64bit (first without uninstall, than with pre uninstall, without Antivirus, as Admin) but the configurator still says 3.1


Klaus Schmitzer

i7-14700KF 5.6GHz Water Cooled /// ZOTAC RTX 4070 TI Super 16GB /// 32GB RAM DDR5 /// Win11 /// SSDs only

DCS - XP12 - MSFS2020

Share this post


Link to post
Share on other sites

  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
×
×
  • Create New...