Jump to content

Sign in to follow this  
motoadve

How to make the Saitek Cessna trim wheel work with Prepar 3D v3?

Recommended Posts

I disconnected it.

It will crash Prepar 3D, and freeze the PC.

Even if unselected from the sim controls and using FSUIPC or viceversa.

 

Windows 7

 

Any ideas?

 

Share this post


Link to post

Plug it in after you have started the Sim, if it's plugged in when you boot the computer it will either crash the sim or not work.

I plugged mine into the Yoke and so far so good but lots of people are having the same problem as you are, I did.


Marty Baclawski

Share this post


Link to post

Same problem here.  If I unplug it or reboot with it plugged in, it freezes the system independent of P3D.  Works fine if it is plugged in after the system has been rebooted.

Share this post


Link to post

On the other side of the coin I have never, at least to my memory, had it directly freeze or crash my system.  I have had it not correctly been recognized whereby I go into FSUIPC and give the wheel a few spins until FSUIPC catches then... then no issue.   But as of late with P3Dv3 I have not even had to do that.

 

Just pointing out the above issues do not affect everyone.  Good luck on solving your issues.

 

Clutch


simwestFOTOREAL series
Photoreal scenery you'll want to fly thru, not over

 

Share this post


Link to post

Yes same here it crashes and a system freeze occurs, I just make sure the Saitek trim wheel control panell is open and spin until it becomes active then start p3d, all ok until I do a system test art.

 

Bob

Share this post


Link to post

Are you running Saitek drivers? If the system freezes it could well be that those are the culprit. I don't install drivers (they don't add anything for me that I'm interested in) for my controls and never had any freezes or problems with either Windows 7 or Windows 8.1. 

 

(I do have the trim wheel)

Share this post


Link to post

+1 for Harry's comment. I didn't install driver. No freeze with trim wheel.


Regards,

Graham Derreck

CYMM

Share this post


Link to post

No drivers here....but the freezes do happen.  Its not a huge deal as I usually don't have to restart very often nor unplug it.  One headache I have seen in the past with it is if the controls are being programmed outside of P3D in something like an A2A control configure program (which recognizes the controllers by their number and not their name) then when you plug it back in after a restart, windows may assign it a new number and mess up all of your assignments in the control configure program

Share this post


Link to post

All I need to do is to spin the wheel once before I start P3D, listen for the Windows sound effect that tells me it has been recognised and then start the sim. It is fine then.

 

However, if I don't spin it first so that it is recognised, then use it after I start the sim, It will freeze and the only way out is to restart my computer!


Stuart Furley

Share this post


Link to post

All I need to do is to spin the wheel once before I start P3D, listen for the Windows sound effect that tells me it has been recognised and then start the sim. It is fine then.

 

However, if I don't spin it first so that it is recognised, then use it after I start the sim, It will freeze and the only way out is to restart my computer!

Yep, still have to do that. did remove the drivers but still the same.

 

bob

Share this post


Link to post

I never had a problem with Windows 7.

 

With Windows 10, the only way to prevent the freezes is to connect the wheel after booting up, and not disconnecting it before shutting down.  I use a USB hub with power switches so I do not have to physically unplug the wheel repeatedly.

 

Saitek has been ridiculously slow with developing Windows 10 drivers, but the Windows 7 drivers were always fine so I am surprised you are having problems.


- Kevin

Prepar3D v4.5 /  X-Plane 11.20 / Aerofly FS2 / Windows 10 / i7-8700k 5.0ghz (de-lidded) / Nvidia Titan Xp 12GB / Dell Alienware AW3418DW WQHD 3440x1440 GSync / Gigabyte Z370 Aorus Gaming 7 mobo / Corsair H100i v2 liquid cooler / 32GB Corsair Vengeance LPX 3000MHz C15 DDR4 RAM / Samsung 860 EVO 2TB (OS) & Crucial MX300 1TB (P3D) SSDs / WD Caviar Black 1TB & 4TB HDDs / LG BD/DVD+-RW optical drive  / Corsair RM750x PSU / Cooler Master Storm Stryker case / CH Products Yoke and Pro Pedals / ThrustMaster Warthog HOTAS stick & throttle / C-Tek CT-203 collective / two Saitek PZ45 Throttle Quadrants (multi-engine) / Saitek Trim Wheel / Saitek Radio and Switch Panels / TrackIR 5

Share this post


Link to post

Barely worked in fsx on windows 7 - hardware short coming - gave mine away had enough of that nonsense 


Rich Sennett

               

Share this post


Link to post

Trim wheel: no drivers installed. Have to remember to spin wheel a few times to dis/reconnect after starting windows and before starting P3D. Same experience as Stuart. Throttle quadrants and rudder will not work without drivers installed.

 

Does anyone know whether or not Saitek is going to update drivers for their pro flight and cessna gear. Last I looked, it appears they've only done their high end stuff.


Regards,

Graham Derreck

CYMM

Share this post


Link to post

Hello !

It seems that the last winsows 10 's update (1511)  had corrected this bug. It's ok for me =)


 

i9 9900 K 5.2 Ghz HT off 32 Gb DDR4 @ 4 Ghz CL17-19-19-44 Team Group Xtrem Asus Maximus Formula XI W10 64 bits pro sur Samsung 960 EVO M2, 2 ème Samsung 960 EVO M2 , RTX 2080 Ti Palit Power supply Corsair 1500 W Gold Screen ACER 28 inches 4K G-SYNC 
Gigabyte 3d mars WC THERMALTAKE WATER 3.0 RIING RGB 360

Share this post


Link to post

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  
×
×
  • Create New...