Jump to content

Sign in to follow this  
tkellogg

Still Can't Calibrate My Controller in Version 3.1 of Prepar3d

Recommended Posts

Very frustrated here. Bought version 3.0 when it first came out but never flew it as I couldn't fly using my joystick. Elevator and ailerons were functioning but not my throttle or rudder control. Regrettfully I uninstalled version 3.0 and reinstalled version 2.5 along with all of my addons. I was excited to see this problem was to be addressed in version 3.1. So after downloading version 3.1 and doing a total reinstall of version 3.1 I still cannot calibrate my controller. There is a calibrate screen now but I am unable to assign my throttle or rudder axes. Is anyone else experiencing this problem. I have not seen anyone post about this issue on Avsim but have seen some people post on P3D forum about their controller problems. I have a Saitek Cyborg EVO Force which has worked flawlessly for years but not with Version 3.0 or 3.1 of Prepar3d. I have long been a supporter of Prepar3d and have had nothing but praise for the software. But lately I am becoming concerned about such a basic problem that exists in this developing software. If I need to purchase a new controller fine but it would be nice to know ahead of time if my controller is not compatible with the latest version of P3D. But apparently even people with newer controllers than mine are experiencing problems. I have downloaded the latest drivers from Saitek. I have windows 7 and a computer capable of running P3D and a lot of addons that runs with FPS in mid 30's. I would appreciate any help anyone can give to get me up and flying with version 3.1. Thanks.

Share this post


Link to post

Very frustrated here. Bought version 3.0 when it first came out but never flew it as I couldn't fly using my joystick. Elevator and ailerons were functioning but not my throttle or rudder control. Regrettfully I uninstalled version 3.0 and reinstalled version 2.5 along with all of my addons. I was excited to see this problem was to be addressed in version 3.1. So after downloading version 3.1 and doing a total reinstall of version 3.1 I still cannot calibrate my controller. There is a calibrate screen now but I am unable to assign my throttle or rudder axes. Is anyone else experiencing this problem. I have not seen anyone post about this issue on Avsim but have seen some people post on P3D forum about their controller problems. I have a Saitek Cyborg EVO Force which has worked flawlessly for years but not with Version 3.0 or 3.1 of Prepar3d. I have long been a supporter of Prepar3d and have had nothing but praise for the software. But lately I am becoming concerned about such a basic problem that exists in this developing software. If I need to purchase a new controller fine but it would be nice to know ahead of time if my controller is not compatible with the latest version of P3D. But apparently even people with newer controllers than mine are experiencing problems. I have downloaded the latest drivers from Saitek. I have windows 7 and a computer capable of running P3D and a lot of addons that runs with FPS in mid 30's. I would appreciate any help anyone can give to get me up and flying with version 3.1. Thanks.

 

The only way I could get my CH Pedals to work in P3D V3 was using paid version of FSUIPC. Haven't got 3.1.  


PF3 Beta Tester

Bob Cardone        P3D 3,4       FlyVirtual.net   Aivlasoft EFB2  /pf3-supporter.gif

 

 

 

Share this post


Link to post

Tell us about your purchase of FSUIPC, and your inability to calibrate your joystick/controls and perhaps I will commiserate with you.

 

Seasons greetings to all,

 

Chas


My first sim flight simulator pD25zEJ.jpg

 

Take a ride to Stinking Creek! http://youtu.be/YP3fxFqkBXg Win10 Pro, GeForce GTX 1080/i7-6700K CPU OCd,16 GB RAM,3x1920 x 1080, 60Hz , 27" Dell TouchScreen,TM HOTAS Warthog,TrackIR5,Saitek Combat Rudder Pedals.

Share this post


Link to post

I have the latest version of FSUIPC

Paid or free?


My first sim flight simulator pD25zEJ.jpg

 

Take a ride to Stinking Creek! http://youtu.be/YP3fxFqkBXg Win10 Pro, GeForce GTX 1080/i7-6700K CPU OCd,16 GB RAM,3x1920 x 1080, 60Hz , 27" Dell TouchScreen,TM HOTAS Warthog,TrackIR5,Saitek Combat Rudder Pedals.

Share this post


Link to post

I suffered from controller issues in P3D v3.0 with my CH Flightstick Pro joystick (it had a significant "left bias", although it was flyable). However, the new calibration routine in v3.1 has solved this issue. I seem to have equal control authority left and right, and the throttle works fine. I use AutoRudder (I don't have a rudder control on the joystick), so I can't help you with that one. It's strange that throttle and rudder are not auto detected for you by the new calibration routine....


Christopher Low

UK2000 Beta Tester

FSBetaTesters3.png

Share this post


Link to post

I finally have my throttle and rudder working. Apparently the version of FSUIPC I was downloading was the correct version however I could not access it as it said it wasn't registered. So I purchased a new license on Simmarket. When I downloaded the version off Simmarket I got the message a later version was already loaded on my computer. So I used the new registration key with the latest software version of FSUIPC that I located on Pete's website. I now have an operation version of FSUIPC. I was able to use FSUIPC to assign the throttle and rudder. Now I am finally flying. Yippee! I will now do all of my assignments of keys and axis as well as calibration through FSUIPC. It can appear very daunting at first but after a thorough reading of Pete's manual I can at least start assigning and flying.

 

Such a shame that it took all this to get flying when older versions of P3D were a cinch to calibrate flight controls and get flying. Best of luck to anyone else having this problem. But if you are having problems with flight controls, FSUIPC is the way to go to get you up and flying.

Share this post


Link to post

...

 

+1


My first sim flight simulator pD25zEJ.jpg

 

Take a ride to Stinking Creek! http://youtu.be/YP3fxFqkBXg Win10 Pro, GeForce GTX 1080/i7-6700K CPU OCd,16 GB RAM,3x1920 x 1080, 60Hz , 27" Dell TouchScreen,TM HOTAS Warthog,TrackIR5,Saitek Combat Rudder Pedals.

Share this post


Link to post

I finally have my throttle and rudder working. Apparently the version of FSUIPC I was downloading was the correct version however I could not access it as it said it wasn't registered. So I purchased a new license on Simmarket. When I downloaded the version off Simmarket I got the message a later version was already loaded on my computer. So I used the new registration key with the latest software version of FSUIPC that I located on Pete's website. I now have an operation version of FSUIPC. I was able to use FSUIPC to assign the throttle and rudder. Now I am finally flying. Yippee! I will now do all of my assignments of keys and axis as well as calibration through FSUIPC. It can appear very daunting at first but after a thorough reading of Pete's manual I can at least start assigning and flying.

 

Such a shame that it took all this to get flying when older versions of P3D were a cinch to calibrate flight controls and get flying. Best of luck to anyone else having this problem. But if you are having problems with flight controls, FSUIPC is the way to go to get you up and flying.

 

As I said previously, if it weren't for FSUIPC, I would have never been able to get my CH rudder pedals to work in V 3.0. I just installed V 3.1 about 20 minutes ago and they work there too, so I am just going to leave it the way it is. 


PF3 Beta Tester

Bob Cardone        P3D 3,4       FlyVirtual.net   Aivlasoft EFB2  /pf3-supporter.gif

 

 

 

Share this post


Link to post

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  
  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
  • Donation Goals

    AVSIM's 2020 Fundraising Goal

    Donate to our annual general fundraising goal. This donation keeps our doors open and providing you service 24 x 7 x 365. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. We reset this goal every new year for the following year's goal.


    21%
    $5,465.00 of $25,000.00 Donate Now
×
×
  • Create New...