Jump to content

Sign in to follow this  
LABOX

Cold and dark too cold. Stuck in PANC...

Recommended Posts

Hello everybody,

 

I got a problem I can´t solve. I´m sitting at the ramp in PANC, trying to start the engines. Panel state is cold and dark. The engine oil temperature is the same as the outside temperature (-9)

 

Naturally the engine won´t start. Is there someting I´m not seeing here? I would be grateful for any solution... 

 

Thanks in advance, Arne...

 

coldoil.jpg

 

 

 

 


LABOX4.jpg

Share this post


Link to post
Share on other sites

-9 aint too bad. a lot of planes can go to -40. I don't own the 747, or have any experience with it, but try turning on your hydraulics and let them warm up. Then try starting the engines. they HYD fluid may be too cold.


Andrew F.P.

 

"That's when I realized, I'm not real; God just imagined me." - Eyedea

Share this post


Link to post
Share on other sites

Hi,

 

I'm not a real 747 pilot nor a engineer but I cannot see anything in the FCOM stating that oil temp could prevent the engine start. In the cold weather procedures, it is said that the normal engine start procedure is to be used with a mention to the oil temp rising slower than usual and the oil pressure being a bit higher (SP 16.3).

Are you sure that the hydraulics are correctly set up (pumps 1-3 auto and 4 to aux), fuel pumps on and APU and engines bleeds ON?

 

Can you post a screenshot of your overhead?


Romain Roux

204800.pngACH1179.jpg

 

Avec l'avion, nous avons inventé la ligne droite.

St Exupéry, Terre des hommes.

Share this post


Link to post
Share on other sites

shure, thanks for the replies guys!

 

engine bleed, fuel pumps, packs  and hydraulics shoud be okay afaik...

 

2017-2-9_22-1-30-440.jpg


LABOX4.jpg

Share this post


Link to post
Share on other sites

Yes your overhead is correctly configured for an engine start.

 

What exactly happens when you pull an engine start switch then flip the corresponding fuel control switch? Do you see N2 rising?

 

Does the issue occur only with low oil temp or in any case?


Romain Roux

204800.pngACH1179.jpg

 

Avec l'avion, nous avons inventé la ligne droite.

St Exupéry, Terre des hommes.

Share this post


Link to post
Share on other sites

Just restarted the sim & computer, working now. Funny. Thanks again for the help!


LABOX4.jpg

Share this post


Link to post
Share on other sites

I believe that w/ autostart on you need to turn on the fuel switch for the engine you want to start or the start button on upper panel won't do anything.  Or else turn off Autostart and then do a manual start -- start button followed by fuel switch for the given engine.

 

Mike


 

                    bUmq4nJ.jpg?2

 

Share this post


Link to post
Share on other sites

PANC is a warm place compared to PAFA Fairbanks.  There is an annual military exercise (BRIMFROST) held about this time of year, and one year when I was expecting to be issued my bunny boots for the trip I learned it was cancelled because it was too cold for diesel.  Turns to jelly and our mobile generators wouldn't run.  Some outfits have gensets than run on JP-4/JET-A, which would work much better in that climate.


Dan Downs KCRP

Share this post


Link to post
Share on other sites

Arne, if you have hydraulic pumps #2 and #3 which are air-driven, it may be best to switch these off for engine start. They will be competing for APU bleed air... You need all the air you can get for starting the engines)

 

If the temperatures are really cold, it may be necessary to manually spin the engines for a certain time period to warm up the oil (before putting the fuel control levers to RUN). If the temperatures are super super cold, I believe engineering has to warm up the oil by other methods (I'm not sure how they do that.... Thankfully, I've never worked in such areas :Tounge:

 

Cheers

John H Watson 


John H Watson (retired 744/767 Avionics engineer)

Share this post


Link to post
Share on other sites

Definitely leave the #2 & #3 Demand pumps off for starting if they are air driven.

 

Depending on engine type and configuration, for cold weather starts we use ignition to both and allow 60sec for lightoff instead of the usual 30sec.

 

But, as others have mentioned, it sounds like you did not put the fuel control switch to run. On the -400s with autostart, you will not get spin up unless you place the fuel control switch to run after pulling the engine start switch. Interestingly, on the -8, the engine starts spinning right away when you pull the engine start switch. 


Mariano Bonaccorso
ROG Rampage V Edition 10, Intel Core i7-6850K 4.6GHz (OC & Watercooled), Corsair VLPX DDR4-3200 64GB , Samsung M2 960 PRO 2TB, SanDisk 1TBx2 (RAID 0)
EVGA GeForce GTX 1080 SC (2xSLI & Watercooled), Asus ROG PG348Q, TM HOTAS Warthog, Caselabs Merlin SM8, Corsair AX1500i, Win 10 Pro 64Bit, P3D Version 4

 

 

Share this post


Link to post
Share on other sites

Curious... As far as I recall, there is no procedure to turn 2/3 hydraulics off during the before start amplified procedure. The cold weather operations supplements don't tell you to turn these off, either.

 

I understand the premise of your instruction, but I think there is no need to switch 2/3 off before start. The apu should manage the pneumatic demand so long as you have remembered to turn the aircon off.

(Hands up... who has forgotten to do this? Me - *both hands up*)

 

Actions relating to start switching are dependent on if autostart is fitted and, if it is, whether it's switched on or not. Judging by your pic, you have it fitted and on; good. All things considered, you should've had spool-up and light-off.


Brian Nellis

Share this post


Link to post
Share on other sites

i do not know about that cold lol but ACA had some issues with their Embraer when it was -30c and below ...

 

for the diesel it will be below -45c where gas and diesel  truck and engine start to have some issues with ignition ...

 

up to -40c nothing special to do just to protect a little the batteries ...


i only found out (cold weather operation) that with GE engines with temp of -35c and below you need to let engines run 2 minutes before touching the thrust lever. the other info i found out for any kind of engines is that during cold weather engine start the oil presure rise may be higher than normal.

Share this post


Link to post
Share on other sites

I'm flying now from RKSI to VOMM with the -400F fitted with GE engines. The SAT at RKSI was -7°C when I started the engines (with the oil at that temperature) and didn't have any issue to start them.

Anyway, the OP said the problem is solved on his side, so I guess the case is closed now.


Romain Roux

204800.pngACH1179.jpg

 

Avec l'avion, nous avons inventé la ligne droite.

St Exupéry, Terre des hommes.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
  • Donation Goals

    AVSIM's 2020 Fundraising Goal

    Donate to our annual general fundraising goal. This donation keeps our doors open and providing you service 24 x 7 x 365. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. We reset this goal every new year for the following year's goal.


    43%
    $10,960.00 of $25,000.00 Donate Now
×
×
  • Create New...