Jump to content
Sign in to follow this  
Boeing or not going

set speed changing after going into level change

Recommended Posts

If this is the logic of the 747 that is fine. I change the speed manually as the airplane is in a mode like vnav/lnav. I dial the speed to a lower number than I am currently flying, and then press level change. Level change resets my speed from the last number I just set, to the current speed of the aircraft. is that by design? Thanks - David Lee

Share this post


Link to post
Share on other sites

If you're in VNAV, how are you even setting the speed since the speed window is blank when VNAV is engaged. As far as I'm aware, you hit FLCH, the present speed shows up in the window, and you dial it down to whatever speed you want.


Captain Kevin

nGsKmfi.jpg

Air Kevin 124 heavy, wind calm, runway 4 left, cleared for take-off.

Live streams of my flights here.

Share this post


Link to post
Share on other sites

My books say...

If VNAV was engaged before the FLCH button was pushed (MCP window closed), the
MCP speed display shows the present FMC target speed. If VNAV
was not engaged, the display shows the higher of present airspeed or
present MCP speed. Selection of a different speed is possible after
FLCH engages.

It's not clear what happens if FLCH is selected when the A/P is in VNAV with speed intervene.


John H Watson (retired 744/767 Avionics engineer)

Share this post


Link to post
Share on other sites
2 hours ago, Qavion2 said:

My books say...

If VNAV was engaged before the FLCH button was pushed (MCP window closed), the
MCP speed display shows the present FMC target speed. If VNAV
was not engaged, the display shows the higher of present airspeed or
present MCP speed. Selection of a different speed is possible after
FLCH engages.

It's not clear what happens if FLCH is selected when the A/P is in VNAV with speed intervene.

In the last PMDG 747 version, and every other Boeing PMDG models, if I manually have a speed set in the window then go to level change, it keeps the number in the window not reset it to the current speed - David Lee

Share this post


Link to post
Share on other sites

Sorry, David, I can't test this at the moment.

I did find more information on it, however.

 

FLCH push....

1) when IAS/MACH window blank, IAS/MACH window opens to FMC
target speed, if valid. If not valid, IAS/MACH window opens to current
speed
2)when IAS/MACH window open, displays command speed

3) when changing from TO/GA to FLCH, IAS/MACH window displays
highest value of current airspeed or selected speed

 

I wish these manuals were written so "normal" people can understand them

:blink:

 


John H Watson (retired 744/767 Avionics engineer)

Share this post


Link to post
Share on other sites
13 hours ago, 777200lrf said:

If this is the logic of the 747 that is fine. I change the speed manually as the airplane is in a mode like vnav/lnav. I dial the speed to a lower number than I am currently flying, and then press level change. Level change resets my speed from the last number I just set, to the current speed of the aircraft. is that by design? Thanks - David Lee

I believe that FLCH is primarily a level-changing command, as the acronym implies. When you press it, you are telling the aircraft "I want to descend (or climb) NOW". It gives priority to the level change. If you open the speed window, and dial in a lower speed, and immediately press FLCH, you are asking it to do mutually contradictory things. It's the old problem of "you can't go down and slow down" (at the same time).

I think that the proper technique would be to activate speed intervention by opening the MCP speed window, dial in your desired lower speed and WAIT. Thrust will reduce and the aircraft's speed will roll back. Once you reach the desired (lower) speed, THEN press FLCH, and your descent will immediately commence, with FLCH using primarily pitch, (and secondarily thrust), to hold your desired speed in the descent.

This is exactly what VNAV does when your flightplan calls for a lower speed in descent than your programmed cruise speed. In this case, you will see a decel point appear on your ND several miles before your TOD, (or before a waypoint that has a speed restriction).

FLCH is more useful in a climb, than in a descent. It is primarily a pitch mode, in which the aircraft will pitch to maintain the current IAS or Mach, with power being added as necessary (up to the current calculated limit) to keep the climb going. If you dial in a higher speed in the climb, pitch will reduce while the speed builds up, (and rate of climb reduces), once the speed is achieved, pitch will again be held  constant, while power is used to keep the climb going. It is easy for pitch to directly control airspeed in a climb, because the aircraft is working against the force of gravity, which acts as a brake of sorts.

In a descent, the opposite situation holds true. The force of gravity is working WITH the aircraft, tending to cause it to accelerate.


Jim Barrett

Licensed Airframe & Powerplant Mechanic, Avionics, Electrical & Air Data Systems Specialist. Qualified on: Falcon 900, CRJ-200, Dornier 328-100, Hawker 850XP and 1000, Lear 35, 45, 55 and 60, Gulfstream IV and 550, Embraer 135, Beech Premiere and 400A, MD-80.

Share this post


Link to post
Share on other sites
Quote

The behavior of the aircraft is correct. Please consult the FCOMs.

Actually, I was :laugh: I didn't fully understand them.

 

In my other favourite sim, during VNAV speed intervention followed by FLCH, the aircraft will speed up/slow down to achieve the speed set in the window (if the speed was different from the MCP window speed). It will not sync with the current speed (unless that is already the target speed). I don't know what David is seeing in v3

 


John H Watson (retired 744/767 Avionics engineer)

Share this post


Link to post
Share on other sites
On 2/26/2017 at 11:14 PM, Qavion2 said:

My books say...

If VNAV was engaged before the FLCH button was pushed (MCP window closed), the
MCP speed display shows the present FMC target speed. If VNAV
was not engaged, the display shows the higher of present airspeed or
present MCP speed. Selection of a different speed is possible after
FLCH engages.

It's not clear what happens if FLCH is selected when the A/P is in VNAV with speed intervene.

When you go from VNAV to FLCH, the target speed that the FMC in VNAV was commanding is displayed in the IAS/Mach window when selecting FLCH, whether the window was closed (FMC controlling speed) or open during speed intervention. During speed intervention, the target speed is controlled directly by the pilot instead of the FMC, so the speed would not change if you were to select FLCH from VNAV with speed intervention.

Also, FLCH is used more, and therefore more useful, during descent,rather than climb. Most operators stay in VNAV during takeoff, climb, cruise, and most of the descent until ATC starts yanking our chain in the terminal area, and then the economy of VNAV is countered by turn left, turn right, slow down, and speed up by ATC, in which case at some point we transition to FLCH (usually below 10,000), when the economy aspects are overshadowed by ATC requirements to fit into the flow of traffic.

There is a ratio of about 60/40 when you are trying to slow down and go down at the same time. FLCH will go more for speed first (60%) then it will for descent (40%) and then once on speed continue the descent at the new speed and the descent rate will then increase.

Share this post


Link to post
Share on other sites

Thanks, Alexander.

David, could you clarify your issue?

Thanks,

Cheers

 


John H Watson (retired 744/767 Avionics engineer)

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
×
×
  • Create New...