guenseli

PMDG 747 QOTSII module version 1.5

Recommended Posts

Hello,

here is the LINDA module for the PMDG 747 QOTSII 

PMDG 747 QOTSII 1_5

simply unzip the content into your modules folder.

If you need a default configuration and in case you install this module the first time, please rename the files in the folder Modules\linda-cfg\aircrafts\PMDG 747 from *.default to *.lua

THIS VERSION NEEDS THE CURRENT FSUIPC VERSION 4.963 or higher

direct download link or   
link to "updated modules" section in the FSUIPC support forum

Have fun!

 

1.5
OH_ENGINE_2_START fixed
748 ND range rotary improved
748 TCAS rotary adjusted

 

1.4
fixes and changes for 747-8 release
Wipers added
748 specific Display Modes added (attention reassign: DSP_AIR has changed to DSP_AIR_ECS)
MCP_AP_All_SWITCH added
added window heat
fixed dome light
added CHKL/VS function (** read below)
added EFB

-----------------------------
**
How does the CHKL/VS function work?
There has to be a switch definded which toggles between CHKL and VS
(in my default assignment it is the CWSA button on the MCP Combo2)

Pressing this switch toggles then the mode between VS (vertical Speed) and CHKL (Checklist),
but only for the 748.

in VS Mode, dialing the VS knob changes the VS. Pressing is similar to MCP VS Switch press.
in CHKL Mode dialing the VS knob will move the CHKL Cursor, pressing will make a selection in the CHKL.

 

1.3
added GSX Library function

Important! Have a look here!!! Need to download the new GSX library

 

1.2
changed elev trim logic, thanks to Stefan
fixed CDU_R_NAVRAD(), thanks to Manfred

1.1
changed Disp logic
fixed MCP display lag

Edited by guenseli
V 1.5

Share this post


Link to post
Share on other sites
Help AVSIM continue to serve you!
Please donate today!

For previous PDMG 747 users, it is recommended that you check and rename any previous modules and configuration folders before installing this new PDMG 747 variant. This is required to ensure LINDA uses the correct setup.

Check folders /linda/aircrafts/ and /linda-cfg/aircrafts/ and remove or rename any folder with the name starting "PDMG 747". 

Share this post


Link to post
Share on other sites

Hello Guys,

I found a bug in the Module. When you want to use the "oh engine 2 start toggle" the switch goes only in position "on".

 

The bug is here:

function OH_ENGINE_2_START_toggle ()
    if _tl("switch_093_74X", 0) then
       OH_ENGINE_2_START_on ()
    else
       OH_ENGINE_2_START_off ()
    end
end
 

to fix this you must change the value "093" to "092" then the switch works fine.

 

Greetz

Charly

Share this post


Link to post
Share on other sites

1.4
fixes and changes for 747-8 release
Wipers added
748 specific Display Modes added (attention reassign: DSP_AIR has changed to DSP_AIR_ECS)
MCP_AP_All_SWITCH added
added window heat
fixed dome light
added CHKL/VS function (** read below)
added EFB

 

-----------------------------
**
How does the CHKL/VS function work?
There has to be a switch definded which toggles between CHKL and VS
(in my default assignment it is the CWSA button on the MCP Combo2)

Pressing this switch toggles then the mode between VS (vertical Speed) and CHKL (Checklist),
but only for the 748.

in VS Mode, dialing the VS knob changes the VS. Pressing is similar to MCP VS Switch press.
in CHKL Mode dialing the VS knob will move the CHKL Cursor, pressing will make a selection in the CHKL.

Share this post


Link to post
Share on other sites

1.5
OH_ENGINE_2_START fixed
748 ND range rotary improved
748 TCAS rotary adjusted

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.