Jump to content
Sign in to follow this  
jjjallen

Can Realair Legacy V2 for FSX work in P3D V3?

Recommended Posts

It's not in the sound cfg. There's an error in the aircraft.cfg, in the [contact points] section:

point.0 =1,  0.82,  0.00, -3.75,  4000,  0,  0.633,  35,  0.13,  1.80,  0.35,   3.1, 3.1, 0,  152, 180 //Tarmac, non-castoring
point.1 =1, -8.04, -5.40, -3.94,  6000,  1,  1.00,    0,   0.30,  2.50, 0.36,    3.1, 3,1, 2,  152, 200
point.2 =1, -8.04,  5.00, -3.94,  6000,  2,  1.00,    0,   0.30,  2.50, 0.36,    3.1, 3.1, 3,  152, 200


Note the "3,1" entry which I have underlined for emphasis.  It should be "3.1".

 

 

 


My system specs: Intel i9-10850@3.6 - 5.2 GHz, NVIDIA GeForce RTX 3080, 32GB  DDR4  RAMNoctua NH-D15 CPU Cooler,1TB Seagate SSD, 4TB Seagate HD, Windows 10, Asus 32 inch monitor, Saitek Yoke, Throttle Quadrant, Rudder Pedals and Trim Wheel     Sims: MSFS2020      Preferred Aircraft  Black Square Bonanza, and Baron, A2A Comanche, PMDG DC-6, Red Wing L1049 

Share this post


Link to post
1 hour ago, AviatorMan said:

It's not in the sound cfg. There's an error in the aircraft.cfg, in the [contact points] section:

point.0 =1,  0.82,  0.00, -3.75,  4000,  0,  0.633,  35,  0.13,  1.80,  0.35,   3.1, 3.1, 0,  152, 180 //Tarmac, non-castoring
point.1 =1, -8.04, -5.40, -3.94,  6000,  1,  1.00,    0,   0.30,  2.50, 0.36,    3.1, 3,1, 2,  152, 200
point.2 =1, -8.04,  5.00, -3.94,  6000,  2,  1.00,    0,   0.30,  2.50, 0.36,    3.1, 3.1, 3,  152, 200


Note the "3,1" entry which I have underlined for emphasis.  It should be "3.1".

 

 

 

Sorry, I quoted the wrong thing.  I found what the other guy above was talking about in the <sim>\SimObjects\Airplanes\RealAir Duke B60 V2\panel\Sound\RASDuke_Sound.ini file.  I haven't tried stripping the directories yet.  I'll give it a try later today.

 


Gregg Seipp

"A good landing is when you can walk away from the airplane.  A great landing is when you can reuse it."
i7-8700 32GB Ram, GTX-1070 8 Gig RAM

Share this post


Link to post
20 hours ago, Gregg_Seipp said:

I don't see any superfluous entries in sound.cfg for the Duke B60 V2 in mine.  Is that where you had them? 

RASDuke_sound.ini inside of Panel\Sound folder not sound.cfg

 

Sorry, my keyboard was working faster than my brain, I see you had figured out the right cfg file. Depending on how you organized your installation (by duplicating Real Air's handling of installing the Turbine) at least make sure the sound ini is showing right location of the actual panel\sound folder.

**edit again.
My install of the B60 v2 is not as you apparently, you stated that you had the install as this<sim>\SimObjects\Airplanes\RealAir Duke B60 V2 

My post dealing with stripping out (or correcting) the wrong sound folder locations will have nothing to do with your install location.

I installed mine outside of P3D folder (trying to keep installs as LM recommends) but I must confess I have the older Legacy v2 installed inside P3D and no problems.

Main reason for installing B60 same as the Turbine was to see if the B60's sound would work without lag and just to see if I could do it. It turned out that I no longer had lag in the sounds as compared with using the sound file replacement earlier.

 


Intel(R) Core(TM) i7-10700F CPU @ 2.90GHz (8 cores) Hyper on, Evga RTX 3060 12 Gig, 32 GB ram, Windows 11, P3D v6, and MSFS 2020 and a couple of SSD's

Share this post


Link to post

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  
  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
×
×
  • Create New...