It's not in the sound cfg. There's an error in the aircraft.cfg, in the [contact points] section:

point.0 =1,  0.82,  0.00, -3.75,  4000,  0,  0.633,  35,  0.13,  1.80,  0.35,   3.1, 3.1, 0,  152, 180 //Tarmac, non-castoring
point.1 =1, -8.04, -5.40, -3.94,  6000,  1,  1.00,    0,   0.30,  2.50, 0.36,    3.1, 3,1, 2,  152, 200
point.2 =1, -8.04,  5.00, -3.94,  6000,  2,  1.00,    0,   0.30,  2.50, 0.36,    3.1, 3.1, 3,  152, 200

Note the "3,1" entry which I have underlined for emphasis.  It should be "3.1".

 

 

 

1 hour ago, AviatorMan said:

It's not in the sound cfg. There's an error in the aircraft.cfg, in the [contact points] section:

point.0 =1,  0.82,  0.00, -3.75,  4000,  0,  0.633,  35,  0.13,  1.80,  0.35,   3.1, 3.1, 0,  152, 180 //Tarmac, non-castoring
point.1 =1, -8.04, -5.40, -3.94,  6000,  1,  1.00,    0,   0.30,  2.50, 0.36,    3.1, 3,1, 2,  152, 200
point.2 =1, -8.04,  5.00, -3.94,  6000,  2,  1.00,    0,   0.30,  2.50, 0.36,    3.1, 3.1, 3,  152, 200

Note the "3,1" entry which I have underlined for emphasis.  It should be "3.1".

 

 

 

Sorry, I quoted the wrong thing.  I found what the other guy above was talking about in the <sim>\SimObjects\Airplanes\RealAir Duke B60 V2\panel\Sound\RASDuke_Sound.ini file.  I haven't tried stripping the directories yet.  I'll give it a try later today.

 

How about getting the F1 GTN750 working?  I have both the FSX and P3D V3 versions.

 

Thanks

jja

20 hours ago, Gregg_Seipp said:

I don't see any superfluous entries in sound.cfg for the Duke B60 V2 in mine.  Is that where you had them? 

RASDuke_sound.ini inside of Panel\Sound folder not sound.cfg

 

Sorry, my keyboard was working faster than my brain, I see you had figured out the right cfg file. Depending on how you organized your installation (by duplicating Real Air's handling of installing the Turbine) at least make sure the sound ini is showing right location of the actual panel\sound folder.

**edit again.
My install of the B60 v2 is not as you apparently, you stated that you had the install as this<sim>\SimObjects\Airplanes\RealAir Duke B60 V2 

My post dealing with stripping out (or correcting) the wrong sound folder locations will have nothing to do with your install location.

I installed mine outside of P3D folder (trying to keep installs as LM recommends) but I must confess I have the older Legacy v2 installed inside P3D and no problems.

Main reason for installing B60 same as the Turbine was to see if the B60's sound would work without lag and just to see if I could do it. It turned out that I no longer had lag in the sounds as compared with using the sound file replacement earlier.