Jump to content

Sign in to follow this  
Petraeus

Maddog 2018

Recommended Posts

I found out, that the set speed is stored in "CM1_ASI_needle3", but I had no success with the other.

Christian

Share this post


Link to post
Share on other sites
On 2.3.2018 at 4:35 PM, guenseli said:

I'd like to quote myself from the download thread and the readme:

"Note:

MCP Combo users: If you use rotaries, dials etc. in the VC, the displays are not synced any more!
Or in other words: the sync is just one-directional, NOT two-directional (only MCP to VC, not back)!

(sorry, thats for technical reasons)"

 

Ok, got it. I was thinking it's for MCP Combo I only, as i am using Combo II.

Thanks for your reply!

Oliver

Share this post


Link to post
Share on other sites
On 4.3.2018 at 12:01 AM, crisu19 said:

Many thanks for the great new Module. It works really fine.

Is there a way to control the following switches, buttons and selectors:

  • ENG Gen 1 & Gen 2
  • CG Dialer / TO Flaps Dialer on pedestal
  • TARA switch abv/norm/below
  • Clock/Timer (RUN/HLD/RST)
  • TERR Button on F/O main panel
  • AC Volt / Frequ/DC Volt Bus Selector to control volt/amp meter on the Elec overhead panel

Did I understood you right, that there are no LVars, Offsets or other variable where I can read current set SPD, HDG, ALT and VS?

Thanks and best regards,
Christian

 

 

Christian, I wasn't able to fullfill all of your wishes, but most

 

1.0 > 1.1
one side sync with timer fixed
SPD two way sync enabled
TRPtxt bug fixed
Generator switches added
TARA switch abv/norm/below
Clock CHR button and Run/hld/rst
Voltmeter selector

 

new module 1.1 uploaded


Guenter Steiner
--------------------------------------------------------------------------------------

Betatester for: A2A, Hifi, Simstarter, AivlaSoft, LORBY 
--------------------------------------------------------------------------------------

Share this post


Link to post
Share on other sites
On 26.3.2018 at 7:26 PM, guenseli said:

Christian, I wasn't able to fullfill all of your wishes, but most

That's really great and highly appreciated, thanks a lot and happy easter,
Christian

Share this post


Link to post
Share on other sites

Hi, i tried your module with my mcp combo but i have a lot of problems. 

All buttons and switch dont work, only the SPD , CRS and hdg and alt when in flight are sync to the new maddog.

The profile is read very well and all setting in linda are ok.

 

i dont know why cannot use the complete functions.

 

many thanks,

Simone

 

 

Share this post


Link to post
Share on other sites

Hi Simone

please post your problem in a new thread under LINDA Support. We will try to help you there. 


Andrew Gransden

Scotland, UK

LINDA Support/Developer - VATSIM and BAVirtual - Airbus Flyer

i7 1TB SSD GTX980 - FSX/P3D - Aerosoft Airbus A318/A319/A320/A321 - FS2Crew

Share this post


Link to post
Share on other sites

Hello everyone, been having so much fun with LINDA that I wish I had more time and neurons left to learn all about LUA but it can get complicated.

One quickie, can the LANDING GEAR alarm be implemented to be added to a button? It is a pain every time you  go below the warning parameter to go and look down the throttle quadrant to stop the warning. Thanks. :)

Jay


Jay Marin

Share this post


Link to post
Share on other sites

First of all I would like to thank you for all the efforts about LINDA and it's modules. Never fly without it.

My question now is : As Leonardo with SP1 has changed the functionality of their NAV and COM radios I would like to ask if it is possible to get this changed functions also for the Maddog X module.?

Cheers,
Michael


Regards,
Michael

Aorus Master z390 / i9 9900KS / GTX 1070@2.1 / 32 GB Ram / all watercooled

Share this post


Link to post
Share on other sites

We are aware that there is a change to the Maddog X radio. What we don’t know is why. If it is to implement the new international 8.33kHz channel spacing then there is a problem. FSUIPC and LINDA can only handle frequencies to 2 decimal places. I don’t own the Maddog X so I am unable to investigate further. 


Andrew Gransden

Scotland, UK

LINDA Support/Developer - VATSIM and BAVirtual - Airbus Flyer

i7 1TB SSD GTX980 - FSX/P3D - Aerosoft Airbus A318/A319/A320/A321 - FS2Crew

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
  • Donation Goals

    AVSIM's 2020 Fundraising Goal

    Donate to our annual general fundraising goal. This donation keeps our doors open and providing you service 24 x 7 x 365. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. We reset this goal every new year for the following year's goal.


    50%
    $12,670.00 of $25,000.00 Donate Now
×
×
  • Create New...