GTX 1080 TI = Blurries

[iFlySimX 748]

40 minutes ago, Afterburner said:

Your settings and your system specs look good to me. Do you get blurries at that specific airport, or do you see the blurries everywhere else?  Can you test it outside that airport?

Everywhere :( 

 

20 minutes ago, Nyxx said:

Am not going to get into all the setting you should change but for a start turn off speed trees = Dynamic 3D auto gen veg. 

Your maxing out your core 0 that's bad. All down to unlimited FPS and them setting am afraid. You might like all them setting but sadly your PC does not.

Please tell me more :)

[fghdgdfdfgfgf 111]

1 hour ago, FunknNasty said:

ITo the topic: I just upgraded from a Haswell and would agree with others here that the processor is serviceable and can give satisfactory performance...

.....but! after upgrading my Haswell/1070 kit to the 8600k/1070 combo I was totally wow'd by the performance difference (same OS install and user settings -apples to apples comparison).

The Haswell does not serve the 1070 any justice...

 

[iFlySimX 748]

Even if I lock my frames to 20, I still get blurries. Could it have anything to do with Vectors or FTX Global? Would a fresh P3D V4 install make a difference? 

[zmak 331]

20 minutes ago, Le Français said:

Even if I lock my frames to 20, I still get blurries. Could it have anything to do with Vectors or FTX Global? Would a fresh P3D V4 install make a difference? 

yes its a known problem. Go to ORBX CENTRAL/settings/ forced migration and run it.. even if you have before wont hurt to do it again

[iFlySimX 748]

21 minutes ago, zmak said:

yes its a known problem. Go to ORBX CENTRAL/settings/ forced migration and run it.. even if you have before wont hurt to do it again

Thanks will try this after this flight!

What I also noticed as I am climbing out of KSFO is that the autogen buildings and ground textures are slow to load. 

[iFlySimX 748]

6 hours ago, zmak said:

yes its a known problem. Go to ORBX CENTRAL/settings/ forced migration and run it.. even if you have before wont hurt to do it again

That did not fix it ;(

[ryanbatc 12,775]

12 hours ago, Afterburner said:

Your settings and your system specs look good to me. Do you get blurries at that specific airport, or do you see the blurries everywhere else?  Can you test it outside that airport?

I agree!  I have a lowly 2500K with GTX 970 and I can get clear textures loaded.  Something else is wrong with him just sitting on that runway.

OP:  Try locking at 30 fps?

[Afterburner 374]

Le Francais, in your case, I think it is best to uninstall P3D completely and then reinstall it. Something must be wrong. After you uninstall it, don't forget to delete the application folders, such as shaders, cfg's, etc.

[zmak 331]

And create back ups at default and fully loaded. Its a hell of a lot easier time wise

[iFlySimX 748]

Thanks everyone! What stunks is that how do I know what add-ons can stay and which ones do I meed to uninstall? PMDG, FlyTampa, Aerosoft, GSX, ActiveSky.

[ryanbatc 12,775]

Before you do that

habe you tried just deleting your P3D cfg and having the sim make a new one?

[iFlySimX 748]

3 minutes ago, ryanbatcund said:

Before you do that

habe you tried just deleting your P3D cfg and having the sim make a new one?

Yes I have, many times. 

[ryanbatc 12,775]

In this picture are taking off or just landed?

[iFlySimX 748]

16 minutes ago, ryanbatcund said:

In this picture are taking off or just landed?

Taking off....Just started to reinstall. 

[Afterburner 374]

I recommend to uninstall all add-ons (I know it sucks, but at least you can rule out any interference by an add-on). After you have reinstalled P3D, check the quality in the default vanilla state. If it is good, you can go ahead with installing the add-ons. If not, there must be something other with the system.