Adam Quinn

PMDG 747-8I Pax Payload Page Not working

Recommended Posts

Hey,

In my PMDG 747-8i, it says the Max Pax for each section is 0 so I can't add any pax. I have gone into the .cfg to see if it was wrong and it was perfect, latest version through the operation manager, everything!

It isn't working, please help.

Regards,

Adam Quinn

Share this post


Link to post
Share on other sites
Help AVSIM continue to serve you!
Please donate today!

1 minute ago, Adam Quinn said:

In my PMDG 747-8i, it says the Max Pax for each section is 0 so I can't add any pax. I have gone into the .cfg to see if it was wrong and it was perfect, latest version through the operation manager, everything!

Using a custom / old panel state? If so, go to your root sim folder, look in the PMDG folder for the 747 panel states, and delete them. Then go into the sim and create new ones.

Share this post


Link to post
Share on other sites
1 minute ago, scandinavian13 said:

Using a custom / old panel state? If so, go to your root sim folder, look in the PMDG folder for the 747 panel states, and delete them. Then go into the sim and create new ones.

On my flight I did load the 747-4 panel state but even before I load a panel state, but they are all 747-4 ones

 

Share this post


Link to post
Share on other sites
1 minute ago, Adam Quinn said:

*UPDATE*

Just checked the 747-400, it ain't working now either

 

Confused by your earlier answer.

Are you, or are you not using panel states, and how are you determining this?

Share this post


Link to post
Share on other sites
Just now, scandinavian13 said:

Confused by your earlier answer.

Are you, or are you not using panel states, and how are you determining this?

Apologies about that, essentially, even before I load a panel state in the 744, or 748, the pax says max 0, and it isn't fixed by loading one.

Share this post


Link to post
Share on other sites

Are you sure these are the maximum limits, i.e. the values in parentheses? 

Can you post a screenshot?

These values are read directly from the aircraft.cfg and I can't think of any other reason to be shown as 0 except of a corrupted aircraft.cfg  file.

 

Share this post


Link to post
Share on other sites
Just now, mfrantz said:

Are you sure these are the maximum limits, i.e. the values in parentheses? 

Can you post a screenshot?

These values are read directly from the aircraft.cfg and I can't think of any other reason to be shown as 0 except of a corrupted aircraft.cfg  file.

 

This is copied from my .cfg

 

// Payload Stations: DO NOT CHANGE ORDER  
station_name.0 = "Upper Deck"
station_load.0 =   50,  55.82, 0.0, 12.5
station_name.1 = "Zone A"
station_load.1 =   18,  90.61, 0.0,  1.2
station_name.2 = "Zone B"
station_load.2 =   43,  57.70, 0.0,  1.2
station_name.3 = "Zone C"
station_load.3 =  100,  16.41, 0.0,  1.2
station_name.4 = "Zone D"
station_load.4 =  112, -22.10, 0.0,  1.2
station_name.5 = "Zone E"
station_load.5 =  144, -64.89, 0.0,  1.2
station_name.6 = "Fwd"
station_load.6 =  76960,  51.86, 0.0, -3.0
station_name.7 = "Aft"
station_load.7 =  57530, -39.39, 0.0, -3.0
station_name.8 = "Bulk"
station_load.8 =  14880, -67.77, 0.0, -3.0

Share this post


Link to post
Share on other sites
Just now, mfrantz said:

Can you post a screenshot of the EFB showing the zeroes?

Its not the EFB its the FMC but sure! Loading the sim now

Share this post


Link to post
Share on other sites

If it is the FMC can you check on the 747-8i if the EFB>OPT>WT & BAL page also shows zeroes?

Share this post


Link to post
Share on other sites
2 minutes ago, mfrantz said:

If it is the FMC can you check on the 747-8i if the EFB>OPT>WT & BAL page also shows zeroes?

Yup I'll check the EFB now, also how do I attach a screenshot to avsim, sorry, never done it before

 

Edited by Adam Quinn

Share this post


Link to post
Share on other sites
Just now, Adam Quinn said:

None if the liveries I have installed have an efb in them, how do I get one in?

Ah. Sounds like an install issue.

Please submit a ticket at support.precisionmanuals.com

Share this post


Link to post
Share on other sites
Just now, scandinavian13 said:

Ah. Sounds like an install issue.

Please submit a ticket at support.precisionmanuals.com

Would a reinstall help?

Share this post


Link to post
Share on other sites
Just now, Adam Quinn said:

Would a reinstall help?

Unlikely - if it were that simple, I would've suggested it instead of support. We'll need to look into this a bit more intensely to guide you through it.

Share this post


Link to post
Share on other sites
Just now, scandinavian13 said:

Unlikely - if it were that simple, I would've suggested it instead of support. We'll need to look into this a bit more intensely to guide you through it.

Ok, not sure I have time now for the whole process, thanks for your help guys, you can close this if you want!

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.