Jump to content

Sign in to follow this  
Rene_Feijen

GTN750 how to plan approach procedures?

Recommended Posts

I am a bit confused how to input a flightplan including the approach.

Say I want to go from KSEA to KMWH. When I put in GTN750 as flightplan lets say KSEA TAGOR EAT, when I want to load an approach I select KMWH, and then select an approach. But that leaves the airport KMWH also in the plan. Should I then simply delete KMWH from the flightplan?


René Feijen

Prepar3DV4 | I5-9600K | 16 GB DDR4 3000 mhz |  MSI RTX 2070 Armor 8GB  | 3 monitor setup for touchscreen RXP GTN 650 and 750 - VC - map display TIR5

IVAO member 471465

ASP3DV4 REX SF3D A2A C178 Bonanza ORBX many! EZCA V3 Simstarter NG

Share this post


Link to post
Share on other sites

Hi,

You might want to start reading the Garmin Pilot's Guide which gets installed alongside the trainer on your hard drive.

Default location is: "C:\ProgramData\Garmin\Trainers\Launcher\Manuals"

Otherwise start the Garmin Trainer launcher and see the manuals there.

It is all explained in detailed in the Garmin manuals (obviously) and AFAIK there was a change regarding the airport staying/removed in the flight plan before/after their 6.50 software release.


Jean-Luc | reality-xp.com
This message from Reality XP is protected by a disclaimer: reality-xp.com/aboutrealityxp/email.html

Share this post


Link to post
Share on other sites
11 hours ago, Rene_Feijen said:

Should I then simply delete KMWH from the flightplan?

Yes, if you are not flying a pattern to overfly the airport, which is usually then a VFR approach with VFR conditions  after cancelling IFR.

  • Like 1

Frank Patton

Gigabyte GA-Z97X-Gaming 7 MOB; i7 4790 4.4Ghz; 16gb DDR3 2300; MSI GTX970 4gb Gaming 100ME, Coolermaster Pro 5 case, Corsair H100i

Former USAF meteorologist and ground weather school instructor; AOPA Member #07379126

There is no limit to what a man can do or where he can go if he doesn’t mind who gets the credit! - Benjamin Jowett

 

Share this post


Link to post
Share on other sites
14 hours ago, Rene_Feijen said:

I am a bit confused how to input a flightplan including the approach.

Say I want to go from KSEA to KMWH. When I put in GTN750 as flightplan lets say KSEA TAGOR EAT, when I want to load an approach I select KMWH, and then select an approach. But that leaves the airport KMWH also in the plan. Should I then simply delete KMWH from the flightplan?

Since you want to land at KMWH.. you just leave it in the flightplan... that is what I do.

1. Enter flightplan:  KSEA TAGOR EAT KMWH

2. Select approach and at some point, activate the approach.

3. that is it..

  • Like 1

Bert

Share this post


Link to post
Share on other sites

Thanks for the tips, I will try them out!


René Feijen

Prepar3DV4 | I5-9600K | 16 GB DDR4 3000 mhz |  MSI RTX 2070 Armor 8GB  | 3 monitor setup for touchscreen RXP GTN 650 and 750 - VC - map display TIR5

IVAO member 471465

ASP3DV4 REX SF3D A2A C178 Bonanza ORBX many! EZCA V3 Simstarter NG

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

×
×
  • Create New...