[23 May 2021] V2.1 Released ! Change Log Here

[byork 2,259]

Are you sure you ran the P3D V5 version of the FS2Crew configurator?

Maybe you ran the P3D V4 version?

[elButz 1]

Hi Brian,

I'm not able to get my FS2Crew to run, the button I assigned to open the FS2Crew window doesn't work in the bus. With the 747 it works just fine.

I've uninstalled the v4 version, then installed the v5 version. After my encounter as above I installed both v5 and v4 versions again over top of the existing v5 install.

Any suggestions to get P3D to recognize the add-on?

[byork 2,259]

Hi Johannes,

It's the same assignment.  Autofeather arm off.  I recommend using the N key.

Take a look at your panel.cfg file for the FS Labs.  You can open it with notepad.

Do you see FS2Crew entries on it?

Also see this thread:

 

[elButz 1]

Thanks for your quick reply! A reinstall of the A320 solved it.

[alessandro.loguercio 1]

The new update is only for p3d v5?

Because for a performance reason I use an old version of fslabs Airbus and P3D (.266 / P3D 4.2) 😂

 

 

[Matty2123 0]

I can’t get hard mute to work I used c button as per manual you can’t click HM and if I press c it’s starts saying instructions Ie completed completed gearpins covers is it a bug? It’s not even going through the flows. 

Edited July 11, 2020 by Matty2123

[byork 2,259]

7 hours ago, alessandro.loguercio said:

The new update is only for p3d v5?

Because for a performance reason I use an old version of fslabs Airbus and P3D (.266 / P3D 4.2) 😂

 

 

It also updates the P3D V4 version.

[byork 2,259]

7 hours ago, Matty2123 said:

I can’t get hard mute to work I used c button as per manual you can’t click HM and if I press c it’s starts saying instructions Ie completed completed gearpins covers is it a bug? It’s not even going through the flows. 

I just tested it.

I press "HM" on the Main panel and mute started flashing on the main panel.

Other part I don't get.  Have you used FS2Crew FSLabs before?

[Matty2123 0]

Yeah I was using the v4 version all I did was press the HM button and nothing happens 

[Matty2123 0]

In the other part I sent the FO out to do his exterior inspection he came back in cockpit flow was flashing and nothing was happening tho ie setting nothing up  

[Matty2123 0]

11 hours ago, byork said:

I just tested it.

I press "HM" on the Main panel and mute started flashing on the main panel.

Other part I don't get.  Have you used FS2Crew FSLabs before?

https://vimeo.com/437594558 video of it 

[byork 2,259]

9 minutes ago, Matty2123 said:

https://vimeo.com/437594558 video of it 

The problem is you're in "Button Control" mode.

Hard Mute is for Voice Control mode only.

Cheers,

 

[Matty2123 0]

Doh gotta remember how to change it lol 

[Skald 1]

It seems that responses for “I have control/you have control” disappeared in this version. Also any hints what to say if speech recognition messes flaps two and flaps full?

[byork 2,259]

Nothing was changed in that area.

In that scenario, there's nothing you can say other than you can manually change the flap or recommand the flap.

Edited July 13, 2020 by byork