Jump to content

Recommended Posts

Hi all,

I'm going to attempt building my own yoke. I'll be using various pieces of hardware and the enclosure will be made of wood. I know - it would probably be cheaper and certainly faster to buy a real yoke but it wouldn't be as fun would it? I have a love for tools and wood in general and I'm convinced (at least for now) I can build a very good yoke.

My inspiration for the yoke comes from the Yoko yoke/Yoko Plus yoke found here:
Yoko Yoke Plus: https://www.virtual-fly.com/en/shop/controls/flight-sim-yoke-yoko-the-yoke-plus
Yoko Plus internals: https://www.dropbox.com/s/ztmwtk5cui45e2q/Yoko plus internals.jpg?dl=0

I'll be using various tools and build the yoke in my workshop:
Drill press: https://www.dropbox.com/s/ci90l4yt2l7rnhk/0F90CE3F-7693-4F22-BA09-32E8EC110180_1_105_c.jpeg?dl=0
Mitre saw:https://www.dropbox.com/s/d14mw7ato4nvcyf/14A65869-5193-4346-AD7A-9A5471DFD054_1_105_c.jpeg?dl=0
CNC: https://www.dropbox.com/s/mwml5sa9orso9rk/181086FC-B938-4092-A69A-FA4B5CF4E08B_1_105_c.jpeg?dl=0

I used to have a small wooden cockpit I could bolt on top of my Saitek yoke 10 yeas ago so I've a pretty good amount of various switches, controllers and sensors:
https://www.dropbox.com/s/fk0ylxjofm44tal/61B6060F-323D-409E-9C29-2B61C3F3FDCD_1_105_c.jpeg?dl=0
https://www.dropbox.com/s/3mp49expht6vhof/5F12D1EC-3BD7-44D1-BA68-A5F7E9997934_1_105_c.jpeg?dl=0

I'm going with hall effect sensors for the pitch and roll axis. Board from Leobodnar will be used as controller. I've got a bunch of hardware coming in over the next few weeks so it should be an interesting build. I'll update the post as the project comes along.

Have a great day!

  • Like 1

Share this post


Link to post
Share on other sites

Nice one. Good luck. Post pics of it.


Alan Bradbury

Check out my youtube flight sim videos: Here

Share this post


Link to post
Share on other sites

The magnets where delivered today. I ordered a few different sizes (3, 4 and 5mm diameter) as I'm not entirely sure what size I should use. These are neodymium magnets so they are extremely strong. I've done a small test with an 8mm diameter magnet and the magnet has to be very close to the sensor in order to get a good calibration.

https://www.dropbox.com/s/sn2q57g5kixmgdq/Magneter.jpeg?dl=0

There's probably some mathematic formula that describes the magnetic field in relation to the hall effect sensor but I'm not an engineer so it's going to be trial and error. Also I've only tested with one magnet close to the sensor. It seems that this sensor has a maximum effective range of 180 degree which is perfect for the roll axis. For the pitch axis I'm definitely going to need some gears of some sort in order to stay within the 180 degree working radius.

Share this post


Link to post
Share on other sites

I would strongly recommend AS5600 magnetic sensors as opposed to a single Hall element. They are specifically designed to measure the angle of magnetic field rotation and are practically immune to any stray magnetic fields. The maximum rotation angle is 360 degrees, but can be easily calibrated to provide a full supply voltage swing for the angle range from 18 to 360 degrees. AS5600's are easily available from eBay or AliExpress.

Share this post


Link to post
Share on other sites
7 minutes ago, SergeyPe said:

I would strongly recommend AS5600 magnetic sensors as opposed to a single Hall element. They are specifically designed to measure the angle of magnetic field rotation and are practically immune to any stray magnetic fields. The maximum rotation angle is 360 degrees, but can be easily calibrated to provide a full supply voltage swing for the angle range from 18 to 360 degrees. AS5600's are easily available from eBay or AliExpress.

Thanks for the tip and explanation of this sensor 👍. I didn't know about this so I'll definitely be looking into this!

Share this post


Link to post
Share on other sites

You are welcome; good luck with your journey! BTW, the easy way to transform the pitch axis movement to magnet rotation is to use a belt/pulley system as shown in the picture of my yoke: https://yadi.sk/i/3eP0zV6UlWZhNw . Here the AS5600 360 degrees' angle is quite handy as you won't need an extra large pulley (in my case it's about 70 mm diameter for the pitch travel of 140 mm). 

Share this post


Link to post
Share on other sites
7 minutes ago, SergeyPe said:

You are welcome; good luck with your journey! BTW, the easy way to transform the pitch axis movement to magnet rotation is to use a belt/pulley system as shown in the picture of my yoke: https://yadi.sk/i/3eP0zV6UlWZhNw . Here the AS5600 360 degrees' angle is quite handy as you won't need an extra large pulley (in my case it's about 70 mm diameter for the pitch travel of 140 mm). 

Wow, thanks for sharing! If my yoke end up looking half as good as yours I'll be happy 😉. Your design looks a bit like what I have in mind with the dual rods (I ordered the rods yesterday - I swear).

Share this post


Link to post
Share on other sites

😀😀😀 If you need extra pictures- please inform; I was documenting the build/ modifcation process quite extensively. The absolute majority of the parts are the standard ones used mostly in 3D-printers. One more bit of advice- if you are planning to use the dual rods/ standard linear bearings try to make sure that the yoke shaft is in the same plane (height) as the rods; otherwise you'll most probably get the additional friction due to the bearings' skew. The rails used in Yoko are less prone to this problem; however the proper quality ones are way more expensive.

Share this post


Link to post
Share on other sites

Thanks for these tips - really appreciated 👍.. Regarding the additional pictures I'll let you know if I'm stuck 😉.

I've ordered a bunch of the AS5600 sensors but it will take a while before they get here. I'm probably going to experiment with the Hall sensors until then and do a swap later.

I believe the rail system used for the Yoko is this: https://www.boschrexroth.com/en/xc/products/product-groups/linear-motion-technology/linear-guides
These rails alone are around 160$.

Share this post


Link to post
Share on other sites
19 minutes ago, CarstenLP said:

Yes, that's right. There is also a huge number of Chinese clones of various quality- not sure if Virtual Fly are using the originals.

Here is another photo of Yoko Plus internals (found in the web): https://yadi.sk/i/48-IWkmQsgI-5Q

Share this post


Link to post
Share on other sites

Wow!  And I thought I was being clever putting rubber bands inside my Saitek Cessna yoke to improve its operation lol.

Great work guys 😀

Pete

 

 

  • Like 1

Share this post


Link to post
Share on other sites
6 minutes ago, SergeyPe said:

Yes, that's right. There is also a huge number of Chinese clones of various quality- not sure if Virtual Fly are using the originals.

Here is another photo of Yoko Plus internals (found in the web): https://yadi.sk/i/48-IWkmQsgI-5Q

Thanks for the link to this image. Haven't seen that.

Share this post


Link to post
Share on other sites

https://vrflightsim.wixsite.com/mysite

 

I have built it. Working very good.

 

Mark


 

Prepare3Dv5 / ASUS Prime Z390A / I9 9900K @ 4.8 GHz / GSkill 32 GB DDR4 3600 MHZ CL15 @ 3400 MHz / RTX4070TI / Windows 10 Home / Monitor Philips 436M6VBPAB / Force Feedback Yoke / Thrustmaster PTR rudder pedals

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
×
×
  • Create New...