Jump to content

Comms Issue - Changing


cchiozza

Recommended Posts

Hi, there is an option in msfs which assist you to if you are using the build in ATC. You have to disable if you are using p2a otherwise msfs will switch back again and again. 

If I'm right you can find it here:

Options/assistance options/piloting/ai radio communication (ATC) 

Check if this option is turned to OFF

Best regards 

Peter 

  • Like 2

Windows: Microsoft Windows (R) 10 Pro, Hardware:  Intel i9-10900K,  32GB DDR4 Ram,  GTX 1080,  SSD M2 512GB (System),  SSD M2 1TB (Data), 
Software:  X-Plane 11.51, Pilot2ATC v2.6.2.3_r2, MSFS2020 

Link to comment
Share on other sites

1 hour ago, Dornus said:

Hi, there is an option in msfs which assist you to if you are using the build in ATC. You have to disable if you are using p2a otherwise msfs will switch back again and again

well   done  forgot  all about  this  option i always  had it  turned  off,  think  you had  solved  the  mystery   🙂

Edited by pete_auau

I7-800k,Corsair h1101 cooler ,Asus Strix Gaming Intel Z370 S11 motherboard, Corsair 32gb ramDD4,    2  ssd 500gb 970 drive, gtx 1080ti Card,  RM850 power supply

 

Peter kelberg

Link to comment
Share on other sites

12 hours ago, Dornus said:

Hi, there is an option in msfs which assist you to if you are using the build in ATC. You have to disable if you are using p2a otherwise msfs will switch back again and again. 

If I'm right you can find it here:

Options/assistance options/piloting/ai radio communication (ATC) 

Check if this option is turned to OFF

Best regards 

Peter 

Thank you I hope it works, I was about to give up....

Chris Chiozza

Link to comment
Share on other sites

  • Commercial Member

Here's a list of options you may want to turn off in MSFS:

Options -> Assistance->Piloting->AI Radio Communications (ATC) - OFF
Options -> Assistance->Navigation Aids->Route & Waypoints - OFF
Options -> Assistance->Navigation Aids->Taxi Ribbon = OFF
Options -> Assistance->Navigation Aids->Landing Path - OFF
Options -> Assistance->User Experience->ATC UI Panel Open at Start - OFF
Options -> Assistance->User Experience->Show Message Log in ATC Menu- OFF
Options -> Assistance->User Experience->ATC Voices - OFF
 

Dave

Link to comment
Share on other sites

2 hours ago, Dave-Pilot2ATC said:

Here's a list of options you may want to turn off in MSFS:

Options -> Assistance->Piloting->AI Radio Communications (ATC) - OFF
Options -> Assistance->Navigation Aids->Route & Waypoints - OFF
Options -> Assistance->Navigation Aids->Taxi Ribbon = OFF
Options -> Assistance->Navigation Aids->Landing Path - OFF
Options -> Assistance->User Experience->ATC UI Panel Open at Start - OFF
Options -> Assistance->User Experience->Show Message Log in ATC Menu- OFF
Options -> Assistance->User Experience->ATC Voices - OFF
 

Dave

Dave, that was it!! Works great now. Thanks, If I missed that in documentation, my fault

Chris Chiozza

Link to comment
Share on other sites

  • 5 months later...

I am using XPlane 12 and encountered this problem  (with ToLiss A346) -- couldn't tune radio, either manually or under P2ATC control, or switch between active and standby.

  I finally discovered that the setting "auto-tune recommended frequencies" was checked in XPlane 's native ATC menu (the page that displays nearby controllers and ATIS) , and seemed to be overriding the P2ATC and manual commands.  Unchecking this option seems to have corrected the problem.

Link to comment
Share on other sites

On 11/17/2022 at 4:21 PM, ASB0101 said:

I am using XPlane 12 and encountered this problem  (with ToLiss A346) -- couldn't tune radio, either manually or under P2ATC control, or switch between active and standby.

  I finally discovered that the setting "auto-tune recommended frequencies" was checked in XPlane 's native ATC menu (the page that displays nearby controllers and ATIS) , and seemed to be overriding the P2ATC and manual commands.  Unchecking this option seems to have corrected the problem.

Well well!  Thank you, this solved my radio freq. problem - would never of thought to look there for a solution. Cheers.

Win11,X-Plane12 b13

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
×
×
  • Create New...