Pushback tool issue

[cchiozza]

The pushback tool from flighsim.io works fine until the pushback?🙃What is the deal se below.  Is it pmdg?

 

https://share.icloud.com/photos/064S8xAVP5RCY28FdOtDBejWg

 

[Bobsk8]

If you are talking about the toolbar pushback, that is all I use both on the PMDG 737-777 and Fenix A 320. Works perfectly every time. 

[cchiozza]

42 minutes ago, Bobsk8 said:

If you are talking about the toolbar pushback, that is all I use both on the PMDG 737-777 and Fenix A 320. Works perfectly every time. 

Were you able to see the video? Is starts swinging the plane around.

Edited January 10 by cchiozza

[hvw]

1 hour ago, Bobsk8 said:

If you are talking about the toolbar pushback, that is all I use both on the PMDG 737-777 and Fenix A 320. Works perfectly every time. 

Also with Fenix in FS2024?

[cchiozza]

1 hour ago, hvw said:

Also with Fenix in FS2024?

I will try it...THx

[cchiozza]

2 hours ago, hvw said:

Also with Fenix in FS2024?

Are you saying it is only compatible on 2024? Is there a 2020 and 2024

Edited January 10 by cchiozza

[hvw]

44 minutes ago, cchiozza said:

Are you saying it is only compatible on 2024? Is there a 2020 and 2024

No, I'm not saying that. In FS2020 Fenix stated that Toolbar Pushback shouldn't be used as problems might occur. However, that was a few years ago. Lately a new version of Toolbar Pushback was released that is compatible with FS2024. However, it so far is not known if this new version can be used with Fenix Airbuses' in FS2024. As these aircraft are in an experimental stage and Fenix don't support these aircraft, yet, they will not confirm if Toolbar Pushback now indeed can be used in FS2024 Fenix Airbus or not. 

 

This is Fenix statement on this matter from a few years ago, but still valid:

 

Toolbar Pushback incompatibility with FenixSim Aircraft

We don't endorse the use of Toolbar Pushback as this plugin can cause severe performance degradation and also issues with the autopilot causing an uncontrollable climb or descent. We have a built-in pushback feature in the EFB's Ground Services page.

Edited January 10 by hvw
Added information

[mwe_EDVK]

4 hours ago, cchiozza said:

Is starts swinging the plane around

You have to reduce the tug speed to two or three kts, its an old problem. After that it should work with fenix too.

[cchiozza]

17 minutes ago, mwe_EDVK said:

You have to reduce the tug speed to two or three kts, its an old problem. After that it should work with fenix too.

Ok thanks, I thought I had the slider down but will check that.

[Bobsk8]

I have been using the pushback with the Fenix for a couple of years, and not had any problems with it. 

[cchiozza]

1 hour ago, mwe_EDVK said:

You have to reduce the tug speed to two or three kts, its an old problem. After that it should work with fenix too.

I am using the P777 but the tug speed and tug direction are grayed out using Planned Pushback.

Edited January 10 by cchiozza

[cchiozza]

1 hour ago, Bobsk8 said:

I have been using the pushback with the Fenix for a couple of years, and not had any problems with it. 

I must be holding my mouth correct....It could be my MSFS2020 install. No way it can be this difficult.

[Andrew2448]

This is a known issue that many people face and the developer has not-quite-but-pretty-much admitted that they have no idea how to fix it. Last communication was on July 18th.

This is from the paid version but it's the same dev behind the scenes and the pushback part of it is almost certainly using the same code. At this point I expect it's never really going to get fixed.

https://forum.aerosoft.com/index.php?/topic/177844-toolbar-pushback-su15-issues/page/5/#comment-1119763

Edited January 11 by Andrew2448

[Bobsk8]

3 hours ago, cchiozza said:

I must be holding my mouth correct....It could be my MSFS2020 install. No way it can be this difficult.

FYI, I have never used a programmed push back. I just start the pushback, and steer with the rudder pedals, to where I want to be.