May 3, 20251 yr Hello, Its been a while that I have flown the B777 meaning the -300 in 2020. Now that I have got the -200 for 2024 yesturday, Im kind of re-learning how to. There are 2 things Im having little issues with One is how do I set the trim?? Im unable to set trim. It only move one spot and returns back. The other is that I can't get the Jetway (Jet Bridge) to Attach to Aircraft. I have click many time on the tablet but nothing and also on the FMC. Can someone help me on this. Any help is appreciated. Thanx you. Edited May 3, 20251 yr by Whisper202
May 3, 20251 yr 1 hour ago, Whisper202 said: Hello, Its been a while that I have flown the B777 meaning the -300 in 2020. Now that I have got the -200 for 2024 yesturday, Im kind of re-learning how to. There are 2 things Im having little issues with One is how do I set the trim?? I forgot if there is a button or scroll down with the mouse and Two I can't get the Jetway (Jet Bridge to Attach to Aircraft. I have click many time on the tablet but nothing and also on the FMC. Can someone help me on this. Any help is appreciated. Thanx you. Can’t help you with the jetway issue - perhaps this is something to do with GSX and where the aircraft door is? The trim on the 777 is set just prior to engine start and the trim setting is given on the page in the FMC on the opposite side to the V speeds. The before start flow is fuel pumps on, hydraulic pumps to auto (turning on the right side first) and then use the pitch trim switches on the yoke to set the desired trim, using the scale readout to the left of the thrust levers.
May 3, 20251 yr Author 15 hours ago, bennyboy75 said: Can’t help you with the jetway issue - perhaps this is something to do with GSX and where the aircraft door is? The trim on the 777 is set just prior to engine start and the trim setting is given on the page in the FMC on the opposite side to the V speeds. The before start flow is fuel pumps on, hydraulic pumps to auto (turning on the right side first) and then use the pitch trim switches on the yoke to set the desired trim, using the scale readout to the left of the thrust levers. Thanks for the help........Ok no worries then for the jetways/jet bridge. As for the trim I have have tried everything from using the Honeycomb yoke to asssign it to, the throttle quandrant and the joystick (Tiller), but no avail I dont know what Im I missing or doing wrong. Whichever I use it doesnt move and if it does its very little. but stays around 4. I do not have pedals. I been researching videos, msg, ect but havent found any that will tell me the exact cause. I also have install the 2024 driver from Honeycomb. Everything else is working fine. Thanks for the help very appreciative. Edited May 3, 20251 yr by Whisper202
May 3, 20251 yr 56 minutes ago, Whisper202 said: As for the trim I have have tried everything from using the Honeycomb yoke to asssign it to, the throttle quandrant and the joystick (Tiller), but no avail I dont know I use the trim buttons on the Yoke to set the trim. Well, the bindings I have to the yoke but you get the picture.
May 3, 20251 yr Author 19 hours ago, bennyboy75 said: Can’t help you with the jetway issue - perhaps this is something to do with GSX and where the aircraft door is? The trim on the 777 is set just prior to engine start and the trim setting is given on the page in the FMC on the opposite side to the V speeds. The before start flow is fuel pumps on, hydraulic pumps to auto (turning on the right side first) and then use the pitch trim switches on the yoke to set the desired trim, using the scale readout to the left of the thrust levers. 3 hours ago, BrammyH said: I use the trim buttons on the Yoke to set the trim. Well, the bindings I have to the yoke but you get the picture. Thanks for the Help.......I Very appreciated. I finally found the issue. I found that I had to disable the Assist Pilot trim in the Assistance Tab that kept me from setting the trim. Once again thanx for your Help.
Create an account or sign in to comment