How to extract RealityXP gauges to repaint...

[Guest abent]

I'd like to repaint these gauges to better fit this panel. I've seen panels where people have done this. I'd like to either repaint them, or put them in a different gauge surround.Thanks, Adamhttp://forums.avsim.net/user_files/52781.jpg

[Guest JeanLuc_]

Very easy!just use the following setting in the INI file:// NoFrame=ON | OFF Set to render a screen only gauge to ease panel bitmap integrationIt will only draw the screen, not the bezel!Just in case, here is the full list://////////////////// EADI Settings://///////////////////// BaroUnits=hpa | inhg Display Baro setting in mb// Meters=yes | no Display Altitude in Meters (in addition to feet)// VMO= Fixed Vmo limit in knots (indicated) - if set to 0, then Vmo is dynamic based on Flight Simulator information// RadAlt=-6.5 Radar Altimeter Calibration// V1= VR= V2= Displayed V1/VR/V2 values - used if no table is provided// VS0= Stalling Speed with landing gear and flaps extended at maximum weight - used if no table is provided// VS1= Stalling Speed with landing gear and flaps retracted at maximum weight - used if no table is provided// ZFW= Zero Fuel Weight. If ZFW is set to other than 0, An extended V speed table is expected and used to compute speeds// FDMode=VBAR | CROSS Flight Director Display mode: VBAR or CROSS// TrendVector=ON | OFF Display the Speed Trend Vector// TrendColor= R,G,B Speed Trend Vector Color// RunwayGuide=ON | OFF Display the Runway Guide on approach// AttCageAdj= Calibration of the Attitude Cage. Positive numbers lowers the artificial horizon.//// CDIColor= R,G,B Color of the CDI indication (25,125,210 = typical EADI blue)// (246,140,246 = typical Magenta)// (100,190,180 = typical Cyan)// (255,255,255 = typical White)// RMI1Color=R,G,B Color for the RMI1 needle// RMI2Color=R,G,B Color for the RMI2 needle// ScaleColor=R,G,B Color for the LOC/GS scale// NeedleColor=R,G,B Color for the LOC/GS needle// TextColor=R,G,B Color of text information (DH setting) and FMA bars// SkyColor=R,G,B Color of the Attitude Indicator Sky area// GroundColor=R,G,B Color of the Attitude Indicator Ground area// FMAColor=R,G,B Color of the displayed Active Modes in the FMA// VSPDColor=R,G,B Color of the displayed V Speeds on the speed tape//// NOEADI=yes | no Display the EADI// NOSPEED=yes | no Display the speed tape// NOALTI=yes | no Display the altitude tape// NOIVSI=yes | no Display the IVSI// NOEHSI=yes | no Display the EHSI// NOFMA=yes | no Display the FMA// EADIZoomFactor= Display Zoom Factor for the EADI screen/////////////////////// EICAS Settings://////////////////////// Engines= Number of Engines// EngineLeft= Engine Number (FS2002 model wise) assigned to Left// EngineCenter= Engine Number (FS2002 model wise) assigned to Center// EngineRight= Engine Number (FS2002 model wise) assigned to Right// N1Max= N1 Scale// N1Warn= N1 Warning (amber area) scale// ITTMax= ITT Scale// ITTWarn= ITT Warning (amber area) scale// N2Max= N2 Scale// FuelUnits=lbs | kgs Fuel Units, in pounds or kilograms// OILMax= OIL Pressure Maximum scale// OILWarn= OIL Pressure Warning (amber area) scale// OILMin= OIL Pressure Caution (red area) scale//// N1Scaler= scales the value range as read from FS to another scale range// N1Offset= offset the value range as read from FS to another base// used together, the JL4 displayed value is: N1displayed = N1 * N1Scaler - N1Offset// ITTScaler=// ITTOffset=// N2Scaler=// N2Offset=//// FlapsSrc= Used with FlapsAlt to translate the model flaps settings to another scale on the EICAS// FlapsAlt= FlapsSrcis a comma separated list of all the flaps settings as found in the aircraft.cfg file// FlapsAlt is a comma separated list of the displayed flaps angles in the EICAS.// If omitted, the EDU will display the real flaps angles as reported by the model// NB: both lists must have the same number of values with a minimum of 2 entries////////////////////// EFIS Settings://///////////////////// CDI=ON | OFF Display the CDI on the EFIS// APTFILT_Type=H|HS Airport Map Filter: runway types. H = HARD / HS = HARD + SOFT// APTFILT_Len= Airport Map Filter: minimum runway length in feet// APTColor=R,G,B Color of the Airport Map symbol (typical 80,153,218)// VORColor=R,G,B Color of the VOR Map symbol// WPTColor=R,G,B Color of the Intersection Map symbol// PlanColor=R,G,B Color for the flight plan route// LegColor=R,G,B Color for the active flight plan leg// TCASColor=R,G,B Color for the regular targets (usually white or blue)// TCASTAColor=R,G,B Color for the TA Targets (usually yellow)// TCASTARAColor=R,G,B Color for the TARA Targets (usually red)// EHSICDIInfo=ON|OFF Display the CDI Waypoint Information in the EHSI in addition to the PFD ///////////////////// RTU Settings:////////////////////// RTU1Pages=1,2 Pages available for RTU1 unit (1= RADIOS / 2= AUDIO PANEL / 3= EFIS/ 4= EFIS2)// RTU1Com=1 Default to COM1NAV1 or COM2NAV2 at startup// RTU2Pages=1,3 Pages available for RTU2 unit// RTU2Com=2 Default to COM1NAV1 or COM2NAV2 at startup// RTUMaster=ON|OFF if ON, the RTU audio panel has priority over FS2002 audio panel settings/////////////////////// Other Settings://////////////////////// GPWS=ON | OFF Activate the GPWS// GPWSLandingFlaps= Flaps angle considered the landing flaps configuration. Uses the translated flaps table to match the EICAS// EFISFans=ON | OFF Activate the background ambient EFIS fan sound// GEARWind=ON | OFF Activate the background wind noise when gear is down// SoundVolume= Overall Gauge Sound Volume (0 to 100 percent)// YokeAPDisco=ON | OFF Activate the Yoke Mounted (button 1) AP Disco command// NoFrame=ON | OFF Set to render a screen only gauge to ease panel bitmap integration//// EADIPopup= POPUP EADI Panel Window Ident number (used for both the included simicon and the screen clickspot)// EHSIPopup= POPUP EHSI Panel Window Ident number// EICASPopup= POPUP EICAS Panel Window Ident number// RTU1Popup= POPUP RTU1 Panel Window Ident number// RTU2Popup= POPUP RTU2 Panel Window Ident number//// EADIPopupAlt= Alternate Window Ident number to toggle when right clicking the EADI screen// EHSIPopupAlt= Alternate Window Ident number to toggle when right clicking the EHSI screen// EICASPopupAlt= Alternate Window Ident number to toggle when right clicking the EICAS screen//// PopupMaster=YES|NO When set to YES, the main panel EFIS displays are frozen when their popup windows are open// ClearMain=YES|NO (When PopupMaster is YES) set to YES also clears the frozen main EFIS when the popup windows are open.//// FDAVail=YES|NO When set to YES, the Flight Director is displayed when the FS F/D is armed.///////////////////////// Extended V Table:////////////////////////// [LEAR45.VSpeeds] Extended VSpeeds Tables//// Flaps.x= Flaps position in degrees for the set (configuration # x= 0,1,2...14)// Weight.x.y= Weight entry in the table (y = 0,1,2...49) for the corresponding flaps setting (x)// // Table speed entries values: (weight in fuel units,V1,VR,V2)// 5000,107,118,129////////////////////////// Extended VS Table://///////////////////////// [LEAR45.VStall] Extended Stall Speeds Tables - replace "LEAR45" in this example with "local" when the INI file// is in the local aircraft folder//// Flaps.x= Flaps position in degrees for the set (configuration # x= 0,1,2...14)// Weight.x.y= Weight entry in the table (y = 0,1,2...49) for the corresponding flaps setting (x)// // Table speed entries values: (weight in fuel units,VS0,VS1)// 5000,102,112////////////////////////////////// [Keyboard] Jet Line 4 Keyboard shortcuts//// Function_Name= set a keyboard shortcut to a function. NB: KNOBO_ = outer knob and KNOBI_ = inner knob,// followed with the direction (either L left or R right)//// each function supports a single or dual shortcut, in the form CTRL+SHIFT+key//// to configure a shortcut, write the key after the = sign:// example EADI_ATT_INC=A will increase the Attitude Indicator horizontal reference with CTRL+SHIFT+A//// when set as EADI_ATT_INC=G,A this is a dual shortcut, requiring to first press CTRL+SHIFT+G then CTRL+SHIFT+A// This is best seen as a primary shortcut to select a device, then a secondary shortcut to select a function.//// In order not to assign a shortcut, simply write nothing after the = sign.////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

[Guest abent]

Thankyou very much JeanLuc.I appreciate the help.Adam