Jump to content
Sign in to follow this  
taguilo

Fuel Flow problems

Recommended Posts

I'm trying to get the fuel flow in the baron 58 to match what is used in the tank, but I have found that it's not evn close. I put 4 Liters in each of the tanks for a total of 8 liters, then I run the engines at 4 liters per hour each ( I make digital gauges to watch all this) I can see they both run at 4 L/hour and I see the fuel in the tank going down. The problem is that it should take 1 hour to empty the tanks yet it only takes 12 minutes??? Here is my code if any one could help this is baffling me. Thanks, Cal Jordan(A:RECIP ENG1 FUEL FLOW, liters per hour) (A:RECIP ENG2 FUEL FLOW, liters per hour) + (>L:TOTAL_FUEL_FLOW, liters per hour)(A:FUEL TOTAL QUANTITY, liters) (L:TOTAL_FUEL_FLOW, liters per hour) / (>L:TIME, hour)%((L:TIME, hour))%!3.2f!

Share this post


Link to post
Share on other sites

Hi,Did you actually do the flight and run out of fuel after 12 min, or that is the value you measured in (L:TIME,hour) ?Tom

Share this post


Link to post
Share on other sites

I did sit and run the engines using a stop watch to time it. They sputtered and quit at 12 minutes 4 times I did that. Same results each time. No unusable fuel either. LOL

Share this post


Link to post
Share on other sites

The baron 58 fuel pph gauge is expresed in gallons/hour. (its tooltip info being wrongly indicated as liter/hour). If you remained sit on the tarmac with the engines running at a fuel flow mark of "4", you were actually consuming a total of near 32 liters/hour. If 8 liters were first loaded, I think that gives you a rough approach to your out of fuel value.Tom

Share this post


Link to post
Share on other sites

I have made my own gauges to monitor the fuel and tried in Gallons/hour, Liters/hour and lbs/hour and converting to Gallons and the results are the same. as you can see above I'm not using a tooltip. I guess I would have to figure out if I burn 8 Liters in 12 minutes, how many liters would I burn in 60 minutes and then configure(Trick) my gauge to read what it should be. Or maybe the fuel_flow_scalar= 0.9 should be adjusted to reflect a more accurate readings. the default installtion = fuel_flow_scalar= 0.9

Share this post


Link to post
Share on other sites

Ok then it seems to be a bug in FS's direct conversion from gallons to liters. The simplest way would be to do the conversion by yoursef:(A:ENG1 FUEL FLOW GPH, gallons per hour) (A:ENG2 FUEL FLOW GPH, gallons per hour) + 3.7854 * (>L:TOTAL_FUEL_FLOW, liters per hour)Tom

Share this post


Link to post
Share on other sites
Guest bookmark

Old topic, old news perhaps. But anyway:I recently discovered that "liters per hour" actually displays liters per second. Strange. /Tom

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
  • Donation Goals

    AVSIM's 2020 Fundraising Goal

    Donate to our annual general fundraising goal. This donation keeps our doors open and providing you service 24 x 7 x 365. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. We reset this goal every new year for the following year's goal.


    53%
    $13,405.00 of $25,000.00 Donate Now
×
×
  • Create New...