AI Traffic not moving, aircraft just sits at the gate

[Guest Michael_CFII_SEL]

Hello,I setup the following American Airlines AI aircraft with AI's Realistic routes. I have no other AI aircraft installed. I'm starting from scratch.AC#1981,457,"PAI A300 AAL"AC#1982,430,"PAI B738 AAL"AC#1983,460,"PAI B752 AAL"AC#1984,461,"PAI B762 AAL"AC#1985,461,"PAI B763 AAL"AC#1986,490,"PAI B772 AAL"AC#1987,453,"PAI F100 AAL"AC#1988,440,"PAI MD80 AAL"I was using these in FS2002's default scenery and everything was working fine at KDFW. I then installed Simflyers KDFW addon scenery, I did not install the static aircraft. I then installed Richard Mohammed's AFCAD file (simflyers_kdfw.zip) that I got from AVSIM. I then started up FS2002, All my American Airlines aircraft are parked at the gates but they never depart or arrive at KDFW.My traffic BGL file is fine. I also de-compiled and then re-compiled just to make sure. There were no errors. I also used AFCAD to scan my BGL's, they are ok as well.I cannot figure out what happened.Any ideas, Have you seen this problem before?.Thank YouMichael

[Guest Captain Barfbag]

What are the flightplans.txt entries like?

[Guest Michael_CFII_SEL]

They look fine,Here is a small clip.AC#1982,N903AN,1%,WEEK,IFR,1/00:24:15,@1/02:51:55,300,F,0797,KMIA,1/10:29:39,@1/13:37:55,320,F,0327,KDFW,1/14:29:35,@1/17:13:15,330,F,1610,KDCA,1/17:58:46,@1/21:11:57,300,F,1057,KDFW,1/22:45:28,@2/02:07:16,300,F,1057,KRNO,2/14:05:52,@2/17:43:39,310,F,1986,KORD,2/18:37:48,@2/19:52:51,290,F,1986,KDTW,2/20:43:18,@2/21:55:54,300,F,1523,KORD,2/23:04:48,@3/01:46:00,350,F,1523,KMCO,3/11:18:10,@3/14:04:17,360,F,1487,KORD,3/14:58:25,@3/19:16:49,320,F,1487,KLAX,3/19:43:53,@4/00:21:58,330,F,0450,CYYZ,4/10:39:40,@4/13:45:28,360,F,0343,KMIA,4/14:49:27,@4/17:36:48,310,F,1879,TNCC,4/18:32:10,@4/21:44:07,340,F,1880,KMIA,4/23:13:57,@5/02:17:17,310,F,1880,KBDL,5/10:19:38,@5/13:16:49,360,F,2131,KMIA,5/14:49:06,@5/17:38:54,310,F,2131,MPTO,5/18:44:07,@5/21:45:00,300,F,2132,KMIA,5/23:04:59,@6/00:02:49,260,F,0926,KTPA,6/00:55:43,@6/01:48:38,270,F,2255,KMIA,6/03:09:51,@6/06:03:20,310,F,0993,MPTO,6/12:55:33,@6/15:47:49,340,F,0960,KMIA,6/17:13:57,@6/19:42:50,350,F,0328,KDCA,6/20:49:17,@6/23:18:10,360,F,0511,KMIA,6/23:34:10,@0/03:05:48,310,F,0470,CYUL,0/10:34:55,@0/14:02:52,360,F,0527,KMIA,0/14:49:38,@0/16:28:04,330,F,0673,MBPV,0/17:41:54,@0/19:27:43,340,F,0746,KMIA,0/21:00:00,@0/23:30:07,350,F,0746,KDCAI don't get it.ThanksMike

[Guest]

Hi Mike,A couple things to try using the sample flight plan you posted:1.Open AFCAD/Fault Finder and make sure there is no errors as far as Unconnected nodes at the gates.2.Go to DFW at:Monday 9:30 AM which would be GMT -5 for flight 1610Monday 5:45 PM for 1057You should see it leave the gate.Alot of AA aircraft sometimes layover in DFW for longer than usual,but if you try the 2 times above..acoording to the plan you posted, you should see some movement.Give it a try, and report backCJ PuttKTPA