Adam Reed

I'm leaning towards putting the O/S on the 4.0 so it gives the whole system as much read/write speed as possible and MSFS on the 3.0....

1 minute ago, abrams_tank said:

While MSFS is not in these benchmarks, it probably performs similar to the other games.  Based on those benchmarks, I'm not sure if paying the extra money for a PCIE 4.0 SSD is worth it.

Thanks for the reply - I already have both SSD's - I got the 4.0 on offer on Prime Day, so I'm trying to decide which one to put O/S and which to put the sim on.

Hi all

I'm currently building a new system and I have two NVME SSD's. This system will primarily be used for flight simulation.

One is a M.2 1TB PCIE4.0 (Upto 6600MB/s) and the other is a M.2 1TB PCIE3.0 (Upto 3500MB/s).

This will be on an ASUS AMD ROG STRIX B550-E Gaming motherboard.

If this was your system, would you put the O/S on the PCIE4.0 or the PCIE3.0?

Thanks

Hi, I think I know the answer and it is an Xplane restriction, howvever is there anyway to extend the night lighting at high altitude so it doesnt look like big square patches are missing as per image below?

Thanks

2 minutes ago, mulgrave said:

There are GTX 1080Ti starting at around 500 pounds.

Hi, where is that? Also, I can get a 2070 for £459, and from what I read the 2070 offers a slight increase over 1080ti?

Evening,

I have just taken the plunge and purchased an oculus rift (on offer) to get into VR as I have been seeing a lot of positive comments around it recently. 

I only tend to fly X-Plane 11 - IFR and predominantly with the Zibo 737 / Flight Factor A320. I use vsync and set FPS to 30fps and have really smooth sim with no stutters, am certainly not a FPS chaser and more than happy with 30fps.

My system is;

i7-6700k OC 4.6GHz stable, Asus ROG Max VIII Ranger Z170 , 8GB RAM, Win10, GTX 980Ti, 32'' monitor 1080p - 1920-1080 at 60hz.

Following the move to VR, I understand my 980Ti may not be good enough, so I am looking to upgrade my GPU. The million-dollar question is, should I go for the RTX 2070 or RTX 2080. GTX 1080Ti is out of the question, because I can only find them for around £900 in the UK, and both the RTX's mentioned are cheaper than that plus have an element of futureproofing (for a while, anyway).

I really don’t mind paying the more for the 2080, but if the 2070 would be sufficient, then I am happy with that.

What are your thoughts?

Thanks

Adam

Thank you for the replies all. I have done some research and have decided to keep saving money and wait for the next gen cards to be released and get a whole new rig at the same time. 

Thanks 

Hello, 

I am considering taking the jump to a GTX 1080 Ti as they are currently on sale with around a £70 saving.

I currently use;

i7 6700k OC to 4.4 Ghz

6GB Asus strix 980Ti 

It will be running a 1080p 1920x1080 on Windows 10 and P3D V4.3, currently running set to 50hz and frame rate unlimited which locks at 50fps. 

I mainly fly in airliners with addon scenery, so some quite hard hitting fps consumers. 

My question is, on paper, will i see an improvement in performance with P3D? 

Many thanks

Adam 

Update - it doesn't have to be only 30hz monitor, a 60hz would be fine as long as it displays 30hz well.

Cheers

Hello, 

I am wondering if anyone can point me in the direction of a 30hz native monitor - anything between 27"-32", reason being, I used to have a monitor that ran native on 30hz and was perfect for P3D, unfortunately my son pulled it off my desk and smashed it so had to throw away. I cannot afford £400 for the same monitor now. 

Budget - £200 maximum if possible, have looked everywhere and cant find one that is native to 30hz. 1080p will do just fine.

Thanks in advance

Adam 

Hi

What i mean, is that ASN and EZDOK all share the same cores that P3D is running on, should this be the case for the best performance ?

Cheers

Hi all.

Just looking for any help out there. I am just wondering about the cores using P3D and ASN in my set up. I have attatched a couple of screnshots of my set up.

It is an i7-6700K upto 4.5GHz on Windows 10 with 8gb ram using P3D V3.2 also have a GTX 980Ti with driver 364.72





All i have in CFG is AM=85 , FFTF=0.1 and TexMaxLoad=2048

Any help greatly appreciated

Adam

Hi all

Hope your well

So, flying EGSS-GCLP today, 3 hours into the flight, no input from me what so ever and had a CTD.

Windows 10, on a pretty clean install (new pc)

-PMDG 737

-ASN

'

'''​

I love ORBX, I simply love it!

Global, Vector, and if your fly in Europe, the Europe LC is fantastic.

Totally changes the simulator in my oppinion.

P.s, its on sale at the moment also! :wink:

Me: It would be a really nice added bonus if 64bit did happen.

Reality: Just dont think it's gonna happen, realistically.

Evening all

Does anyone have EZDOK working on 3.1 yet, if so what version are you using?

Thanks

One thing I would say, as you said you needed to defrag says your on a HDD, one thing I would advise you do is get a good SSD and put p3d on that.

I have a 6700k at 4.6ghz and a gtx 980ti and couldn't be happier. If your budget will allow I would certainly go for a 6700k.

I have a i7 6700k with a GTX 980ti, haven't installed p3d yet but I hope it will give me good results.

Oh that sounds like a great monitor.

I went ahead and bought an LG 34UC97C-B last week and must say I love it and can't wait to get P3D running on it. I decided against 4K, and am more than happy with this...

I have Corsair H110i, cheers

Will I still be able to use my IFly 747/737 and my 3rd party scenery in the academic version?

Yes, you will.

Thanks all, Ill have a look when P3D is running.

I havent turned the thermal protection off, infact I only had the rig 2 days ago, how would I check that or would it naturally be on?

Thanks

Nice choice Egbert. How is it?

Thanks for your input everyone, I am going to hold fire I think until 3.1 and configure my new comp and get rid of everything I don't need first.. 

Thanks again