Rod

I am reading that the max speed on the PA46-500TP Meridian is 260 KIAS. But the documentation from Carenado says 188 KIAS. That is slower than the Mirage 350, which does not make sense. When I try to go over 188 KIAS, I get the engine overspeed warning. What am I doing Wrong? Rod

I am trying to program the Bravo throttle using the standard P3d settings, so far not doing too bad. it would be a lot easier if I could find a simple picture of the throttle with the buttons numbered. The buttons are a bit of a challenge since P3d uses a single key press for two different functions, like CTRL + . to set and release parking brake and it will not let me program switch 32 and 34 for the same function. Rod

I found a uninstall SVS exe file hidden in P3d. V4, Ran it, problem solved. SVS does not load. Thanks all for the suggestions Rod

I have the 172 taken care of, it had a exe file to remove it. But when I load the C182 or any of the other G1000 planes, SVS loads but will not work, I don't actually get SVS on the PDF, and of course the ter err. I want to eliminate SVS, but cant find a removal file. Rod

Please bear with me. I have been away for a time due to medical reasons and I am taking care of a sick wife. I have little time to fly. I have searched for ways to get Carenado SVS to work and came up with over a hundred answers, non of which worked. I have P3d v4. I solved the 172 problem by uninstalling it's SVS. I would like to uninstall SVS and use the G1000 with out but I can't find out how. I would like to use the little time I have flying, not messing. Thank you for your indulgence. Rod

Thanks for the information. I have never used FSUIPC and I don't think I am ready for any new complicated software. I hope the Honeycomb software will help program the lights on the Alpha also. Rod

New bravo on it's way. Will I need any add on software for it to work with P3d v4? I only fly GA aircraft, right now single engine, going to try twin. I'm old and slow. Rod

I purchased the Alpha yoke from my pilot store after waiting almost two years of it's coming next month. Now the only way I can find the bravo throttle is in a set with the yoke, what a rip off. Honeycomb did make a good product, but I have never seen so much hype, promises and excuses from a company. I am 80 years old!!! I don't have that much more time to wait. Rod

I have P3dV4 and Honeycomb yoke. The rudder trim on my Alabeo M20r Ovation is not working. I use the mouse to activate the trim switch and nothing happens. I set up a trim switch on my Honeycomb and nothing happens, the indicator does not change. I can manage a take off most of the time but it is really squirrely. I usually go down the runway in a S pattern. Rod

Does P3d v4.5 log into the internet automaticly? My internet provider has instigated a data limit, so I have to watch my usage.

Eduard, Sorry, I can't help with the Phenom 100. I'm still learning how to fly single engine prop planes. Maybe some day, I will try twins or jets. Good luck, I hope you get it straightened out. Rod

I finally got my SVS working but the mountains in the PDF seem a lot further away than they actually are. I haven't tried night flying through the mountains yet, but I think it would lead to disaster real quick.

Eduard, If you are talking about the SVS on the C172SP, go to sim objects/ airplanes, scroll down to the C172SP g1000, click on that and you should see SVS application and uninstall SVS. When you click on them it looks like they are doing the same thing but the uninstall actually works.

Scimitir, I was having the same problem, I had four planes working great on the SVS system. When I installed the C172sp a no lic message on those four planes and SVS would not work. I tried your suggestion and they all now work. Only one problem, I don't have SVS on my C172SP now. Carenado just can't seem to get it right. Rod

johncott, I was just flying around Las Cruces NM. sightseeing and decided to go to Deming. I got the altitude I wanted pointed the aircraft west, pressed the altitude hold, the heading hold and the autopilot. I thought it would be simple. there are few directions available. Thanks for your reply, looks like I will have to do more studying. Rod

I have the Alabeo M20 Ovation for P3d V4 and can't get the autopilot to work. I get to the altitude and the heading that I want then press the altitude hold button, the Heading hold button then the AP button. The airplane then goes into a right hand bank instead of staying on heading. I do not know what I am doing wrong. Rod

Does anyone know the footprint dimensions of the honeycomb throttle? Also, how it will mount?

Try the My Pilot store. They are in Scottsdale, AZ. I just purchased my Honeycomb Alpha for $249.00. I haven't used it long enough to give a review, but it is a lot smoother than my CH. I fly mostly single Eng. GA. When the Bravo throttle comes out I will probably try twin Eng.

Thanks to everyone for your suggestions. I will probably check out Little Nav Map and Navigraph. I kinda like the price on LNM. Rod

I am looking for a flight planner map and an in flight map to replace the very small map on P3d v4.4. Hopefully not to complicated, I'm very new at this. It is very time consuming clicking the edge of the map over and over to get where your going.

I am using P3d V4.4 and I have my megascenery files at the top of my scenery list and it seems to work great. Also, since megascenery files take a lot of space, I purchased a USB 3.1 Sandisk external SSD just for megascenery files and it is working great and leaves a lot of room on my C drive. I installed direct, so no information on DVD.

I don't have any answers, But I do have another question. I wear glasses with progressive lenses and when you get very far off center they get blurry. Does anyone have experience with this?

Hi all, I'm getting started again after a long absence. I am a pilot wanabe but at 78 years old it's not likely. So I will take the next best thing. I fly G.A aircraft out of mostly small to medium airports. Right now my favorite plane is the Alabeo M20R ovation. I am using MegasceneryEarth, and have New Mexico, Ariz. and north and south Calif.. My home base is Las cruces NM and I have flown over parts of NM in small planes, as a passenger. I also used to live in Yuma, Ariz. and flew out of there, going to Phoenix and San Diego. I am impressed at how realistic the scenery is. Now all I have to do is learn to fly, use the radio and use the GNS 530. I have a long way to go. Unfortunately I don't have the time to fly as often as I would like.

Has anyone actually got their hands on a working model of the Honeycomb Yoke or Throttle? It looks like it would be a great Yoke and I am sure there are a lot of people waiting for it. But it is starting to look like just air ware.

abarter, Thanks for the reply. I really like MSE but it sure takes a lot of room. So far I have New Mexico, Arizona and California. I am new at this and fly GA aircraft mostly from small airports. Rod