Search the Community

Hi everyone, I just received a response from Flight1 that UTlive will be updated for v4, but they don't know how long it will take at this stage. Just out of curiosity, are there any beta testers out there using UTLive in v4? John

(copied from my post in the UTLive support Forum, but hoping I'll get more suggestions and a fix from here) OK, so I've had a ton of issues with UTLive since I updated P3D to 4.4 (not blaming P3D or UTL, but something happened when I upgraded). Here's the short version of whats been going on, then I'll get to my findings as for where I am in testing right now and HOPEFULLY someone will know whats happening so I can get this issue resolved. Prior to updating P3D from 4.3 to 4.4, I had 0 issues with UTLive and all my assignments were showing up perfectly. Short version: Upgraded P3D from 4.3 to 4.4 and UTLive from 1.1 to 1.2. At that time I had a few issues which caused me to have to do a full uninstall and reinstall of P3D and ALL addons. After reinstalling UTLive, I changed the repaints.xml to the backup I made just before updating UTLive to 1.2 (I have over 1000 repaints assigned) but then hardly any traffic would appear (only a very small amount of the default Daedalus would show). Deleting my repaints.xml and allowing UTLive to make a new default one would show the airports full of traffic again. I thought the issue was my backup of the repaints so using the default, I spent hours reassigning over 500 aircraft and I went to do a flight and the airports were empty again. What I've found out: I thought maybe the issue was that there was a bad assignment like I had not made the % in the assignment equal to 100% in one of the aircraft so I checked them all and they were all correct. I then thought maybe it was an aircraft that was no longer compatible somehow that was causing the entire repaints.xml to become corrupt. So, I deleted the repaints.xml and yet again allowed UTL to make a new one. I started P3D and set my location to OMDB and the airport was full again and I made sure to check the Emirates A380 was showing and it was as the UTLive repaint and model. I closed P3D and opened UTLive program and this time, I selected Emirates Airlines, selected the A380, and reassigned ONLY that aircraft to my A380 (TFS model updated for P3D 4) and saved. I restarted P3D and set to start at OMDB and launched. To my surprise, the airport still looked pretty full, but then I noticed there was not 1 single Emirates A380. So it seems that every aircraft I assign a paint to does not show up in the simulator. This leads me to believe this may be a settings issue or a path issue, so if someone can point me in the right direction? Here are some screenshots of my current settings and paths: http://prntscr.com/mvf3l7 - UTL Dashboard http://prntscr.com/mvf3v5 - UTL Simulation tab settings http://prntscr.com/mvf41r - UTL Configuration/Aircraft http://prntscr.com/mvf483 - UTL Configuration/Flt Sim http://prntscr.com/mvf4fc - UTL Configuration/Traffic http://prntscr.com/mvf4l1 - UTL Configuration/Installs http://prntscr.com/mvfbqn - AI Aircraft Editor with Emirates A380 selected and showing at the bottom model is MDLX P3D SimObjects.CFG info - File location path: C:\ProgramData\Lockheed Martin\Prepar3D v4 Full SimObjects.CFG with my AI Aircraft folder highlighted at the bottom (folder where all AI aircraft I have except TrafficGlobal aircraft reside): [Entry.0] Title=Default Airplanes Path=SimObjects\Airplanes Required=True Active=True [Entry.1] Title=Default Avatars Path=SimObjects\Avatars Required=True Active=True [Entry.2] Title=Default Rotorcraft Path=SimObjects\Rotorcraft Required=True Active=True [Entry.3] Title=Default Ground Vehicles Path=SimObjects\GroundVehicles Required=True Active=True [Entry.4] Title=Default Boats Path=SimObjects\Boats Required=True Active=True [Entry.5] Title=Default Animals Path=SimObjects\Animals Required=True Active=True [Entry.6] Title=Default Misc Path=SimObjects\Misc Required=True Active=True [Entry.7] Title=Default Submersible Path=SimObjects\Submersible Required=True Active=True [Entry.8] Title=Default Weapons Path=SimObjects\Weapons Required=True Active=True [Entry.9] Title=Default Countermeasures Path=SimObjects\Countermeasures Required=True Active=True [Entry.10] Title=utLive Aircraft Path=C:\USERS\STEVEN\DESKTOP\P3D ALL\UT LIVE\utLive Aircraft Required=True Active=True [Entry.11]Title=AI Aircraft Path=C:\Users\Steven\Desktop\P3D All\Traffic Global\TrafficGlobal\TrafficGlobalFleet Required=True Active=True Title=TrafficGlobalFleet [Entry.12] Title=Addon AI Aircraft Path=SimObjects\AIAircraft Required=True Active=True Please let me know if there is any other setting or CFG that I should check. Thanks.

Hi Sirs, Just downloaded and installed UTlive into my P3Dv4.2 and i was wondering how do i update the liveries? I noticed also that i dont have 777-300ers and some airline liveries are out dated. Also how do i model match the liveries to vpilot? Thanks, Francis

Hi everyone, I read over in the UT forum that UTLive can be set up by modifying some lines in the xml. Anyone had any success with this yet? If so, can you share what you did? It would be great to have that up and running as we wait for Flight1 to come out with their patch. Thanks, John