Search the Community
Showing results for tags 'brakes'.
Found 16 results
-
Hi, so I’ve had msfs2020 for a while and so far it was very good👍🏼. While landing tho, I noticed that even if the reverse thrust is at maximum power, it doesn’t slow the aircraft too much. I mean if I activate the spoilers and the reverse thrust at maximum and don’t use the normal brakes, the plane goes off the runway, which I know it’s not realistic at all. The only way for me to prevent that is by using the regular brakes with reverse and spoilers. Do you know if it is a glitch, or can I fix this somehow?
-
This is an odd one. Have been trying to solve this for about 3 hours. No matter which B747 variant I attempt to load, when I disconnect all ground services/vehicles and set the wheel chocks to "REMOVED", a "CHCKS INHBT message appears under all the service vehicle lines in the CDU. I read Kyle's response to another user that mentioned if you load P3D with a PMDG 747 as default or switch between variants in a session, this can happen... but that isn't the case here. Here's the scenario: 1. Load P3D with default F-22 2. Load any B747 at any airport with the "747 Short" panel state 3. Verify there are no ground services or vehicles connected. 4. Verify visually that the chocks are set in-place on the landing gear. 5. Select "Wheel Chocks" to "REMOVED" on the CDU 6. CHCKS INHBT message appears in CDU under all service vehicles. What I've done: 1. Searched all the provided PMDG 747 PDFs - found nothing on this issue 2. Searched the internet for comments on "CHCKS INHBT" - nothing found 3. Removed the modified Prepar3D.cfg and allowed P3D to recreate - problem persists 4. Loaded a B747F model - same issue occurrs 5. Disabled ChasePlane (problem stared after I loaded it) - problem persists Any ideas? What file is used by all QOTS B747 variants that could be causing this? Thanks in advance for your help or suggested troubleshooting steps!
-
Hi, I know this is an old topic and I've searched everywhere for a solution but haven't found one yet so I thought I'd ask anyway in the hope that someone out there that reads this has worked one out. The auto brakes on my Aerosoft Airbus X A320 and A321 disconnect every time I land. I've tried low and medium and tried bringing the throttles to idle at a variety of hieghts i.e. 20', 30'. 40' and 50' just before landing but the deacceleration green light pops on for a second then both lights go out and I have to brake manually. I've also tried using reverse thrust and not using reverse thrust. I can't believe there isn't a solution to this very insignificant but annoying little problem. Any help from anybody would be sincerely appreciated. Regards Steve
-
Hello! (im from belgieum so my inglish is not super) First of all im Mert and i bought a pmdg aircraft. But my parking brakes are not working after i start to taxi The little red light is on but 'the parking brake is set' text is not on. My wheel chocks set is not working too after i start to taxi. Do you guys know how i can fix this? Mert Tekelioglu
-
I have some problems wih the prakes. When I load up the 737 the brake temperature at about 7. to 10. without doing anything. So, with this temperature the brakes doesn't works. Any ideas? Thanks for help.
-
Been fooling around with this beauty for a bit... but I seem to be having an issue with the auto brake usage.. it works fine on a rejected takeoff..(disengages the way it should) but on landing it refuses to disengage.. (yes I have moved the switch to off) it only disengages if I snap on the parking brake ( Ctrl .) and off again to disengage the auto brake...after which I lose full use of the manual braking... its just non-response even on the keyboard. I am using a Saitek X45 set and I can find no documentation in the Manual about troubleshooting brakes. Any suggestions? Ruining my life..kinda
-
Hello, I have brakes, both left and right set to joystick trigger button (Logitech X-52 Professional) and it works, but there is about a second worth of delay before brakes take effect and braking action starts. This also happens visually. When I press the brakes, the pedals in VC twitch a bit and then gradually go down. This makes speed control rather difficult and unpredictable. Is anyone else experiencing this or know of a solution?
-
Hello! (im from belgieum so my inglish is not super) First of all im Mert and i bought a pmdg aircraft. But my parking brakes are not working after i start to taxi The little red light is on but 'the parking brake is set' text is not on. My wheel chocks set is not working too after i start to taxi. Do you guys know how i can fix this? Mert Tekelioglu
-
Hello! (im from belgieum so my inglish is not super) First of all im Mert and i bought a pmdg aircraft. But my parking brakes are not working after i start to taxi The little red light is on but 'the parking brake is set' text is not on. My wheel chocks set is not working too after i start to taxi. Do you guys know how i can fix this? Mert Tekelioglu
-
Hello, When I Land in the PMDG 737NGX I activate the reversers (which take ages to come out) and then at 70 kts i turn off the reversers and use the toe brakes but they dont work and i over run the runway! Can Anyone Please Help Me? Kind Regards David
-
Hi, I use PMDG 737-800 NGX and have recently run into a problem that occurs on all my flights. I use the autoland system, no problem, flare arms without rollout then i disengage autopilot, touch down, use reversers to 60kts, then apply manual braking. As far as I know, I haven't done anything wrong. Then, as I come to about 30kts, the brakes stop working altogether including my parking brake; I just keep rolling. The only way I have been able to stop from this point onwards is to use my reversers again. I've looked online and found no solution to this, please help! Thanks in advance.
-
Hi to all, I'd like to assign steering tiller to my Logitech G13 minijoystick. The problem is that this minijoy is not so precise like a normal joystick and I'm trying to fine tuming it via FSUIPC, but I'm not quite expert. I want to assign X axis to steering tiller and Y axis to brakes (L and R) on my G13. The problem is that this minijoystick tends to override my FLY5 axes, so I have to correct with my rudder (when I release tiller with G13), and if I brakes with G13 (Y axis) it works fine, smooth brakes, but then brakes are always applied, even i increase throttle. Does anyone have some tips on how to fine tuning with FSUIPC to solve this issue or any suggestion to manage tiller and brakes? I also own another old joystick, a MS sidewinder 2, maybe could help? Thanks to all in advace -
I got a BIG problem in FsX, always when I stop by using brakes or engage the park brakes the park brakes won't disengage :nea: . This started some time ago, I've seen this both on default and addon aircraft (PMDG NGX mostly). I uninstalled FSUIPC and no change.
-
Hello, I have this situation and it just happens this week,as I can recall. It only occurs with the PMDG B737 series. I have tried all the other a.c. from PMDG and the a.c. from FSX but it is only B737. When I load the aircraft it loads with the parking brakes set. Pressing the dot (.) does actually releases the parking brakes, but the text remain there. Applying ctrl+. does engages the parking brakes, so it functions. How can I make the text disappear when the parking brakes are released?? It is just annoying for I have to check whether the are released or not. Carlos
-
I am on the ground ready to taxi and the parking brakes will not release?
-
Hello! (im from belgieum so my inglish is not super) First of all im Mert and i bought a pmdg aircraft. But my parking brakes are not working after i start to taxi The little red light is on but 'the parking brake is set' text is not on. My wheel chocks set is not working too after i start to taxi. Do you guys know how i can fix this? Mert Tekelioglu
