Jump to content

Archived

This topic is now archived and is closed to further replies.

YpeReitsma

no rudder/nose wheel steering on take-off

Recommended Posts

No CTD's so far, guess I'm lucky. Every now and then the system freezes/hangs though, but recovers after a few seconds. Installed the latest hotfix. Problem on take-off: can't keep the aircraft on the centerline, it won't react on my rudder pedals at all! I checked with the "system screen" on the lower CDU and they were/are working all right. Anybody? I use FSUIPC but without the calibration. For everything else: I'm still smiling flying this one (and looking around in the cockpit), great! Greetings, Ype Reitsma

Share this post


Link to post
Share on other sites

Have you checked the assignments are correct and there are no conflicting assignments? Have you checked all hydraulics are on, and yaw damper is on?


Di Agron

 

Dell XPS 15 L502X | Intel i5-2540m @ 2.60GHz | 4GB DDR3 1333MHz (2x2GB) | nVidia GT525M | Seagate 500GB 7200RPM | 15" 1366x768 | 23" LG 1360x768 |

 

Got a hardware question? Ask:

 

HERE (Mobo's, Ram, CPU's, custom builds, general hardware etc)

HERE (Graphics cards, monitors, drivers etc)

HERE (Peripherals/Hardware and related drivers)

HERE (Internet/Networking)

 

PMDG FMC NavData out of date message fix HERE

Share this post


Link to post
Share on other sites
No CTD's so far, guess I'm lucky. Every now and then the system freezes/hangs though, but recovers after a few seconds. Installed the latest hotfix. Problem on take-off: can't keep the aircraft on the centerline, it won't react on my rudder pedals at all! I checked with the "system screen" on the lower CDU and they were/are working all right. Anybody? I use FSUIPC but without the calibration. For everything else: I'm still smiling flying this one (and looking around in the cockpit), great! Greetings, Ype Reitsma
Use FCUIPC for calibration and axis assignations. It's far better than FS. Make sure that you delete all assignations in the FS control setup.

Omar Josef
737/757/767

Share this post


Link to post
Share on other sites

Thanks for the responses! I dived in FSUIPC for another time and yes, I had overlooked something: there was a conflict with the rudder assignment! Works perfect now. I used to calibrate through FSUIPC but PMDG advised in the intro-document for the NGX to calibrate with the configprogs of the hardware and use the "send to FS" assignment in FSUIPC.So no calibration of the flying controls in FSUIPC no more. Still quite responsive. Only axes I calibrate in FSUIPC are the gear lever and the reverser (prop and mixture levers) of my yoke. Ype Reitsma

Share this post


Link to post
Share on other sites

  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
  • Donation Goals

    AVSIM's 2020 Fundraising Goal

    Donate to our annual general fundraising goal. This donation keeps our doors open and providing you service 24 x 7 x 365. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. We reset this goal every new year for the following year's goal.


    43%
    $10,945.00 of $25,000.00 Donate Now
×
×
  • Create New...