HowardChristian

Revolution Sim TQ Stab Trim Needles Don't Move

Recommended Posts

The TRIM INDICATOR Needles don't move on my Motorised Revolution Sim TQ. 
They are stuck at 0 Nose Down position. 
The Rudder trim Wheels do operate ok. 

Does anyone have any ideas or even a Sioc Test script we could try? 

(I apologise if this is not the correct forum to post, if necessary could moderator please move)?
Copy of the SIOC Script & Sioc.ini below.

// ***************************************************************************** 
// * Config_SIOC ver 4.01 - By Manuel Velez - www.opencockpits.com 
// ***************************************************************************** 
// * FileName : throttleSIMAV_V17.txt 
// * Date : 9/04/2012 


Var 0166, name Reverser1, Link USB_ANALOGIC, Device 1, Input 4, PosL 5, PosC 125, PosR 255 
{ 
IF &acongnd = 1 
{ 
&Leverdiscon = 0 
&throttleman = &A1 / 0.0154 
IF &A1 = 0 
{ 
&throttleman = &Reverser1 * -16 
} 
} 
} 

Var 0167, name Reverser2, Link USB_ANALOGIC, Device 1, Input 5, PosL 5, PosC 125, PosR 255 
{ 
IF &acongnd = 1 
{ 
&Leverdiscon = 0 
&throttleman2 = &A2 / 0.0154 
IF &A2 = 0 
{ 
&throttleman2 = &Reverser2 * -16 
} 
} 
} 

Var 0200, name Thr1FwdSpd, Value 45 // THROTTLE 1 FWD VALUE 

Var 0201, name Thr1BckSpd, Value 175 // THROTTLE 1 BACK VALUE 

Var 0202, name Thr1RtrdSpd, Value 195 // THROTTLE 1 RETARD VALUE 

Var 0203, name Thr2FwdSpd, Value 45 // THROTTLE 2 FWD VALUE 

Var 0204, name Thr2BckSpd, Value 175 // THROTTLE 2 BACK VALUE 

Var 0205, name Thr2RtrdSpd, Value 195 // THROTTLE 2 RETARD VALUE 

Var 0206, name SpdBrkOpnSpd, Value 120 // SPEED BRAKE OPEN VALUE 

Var 0207, name SpdBrkClsSpd, Value 190 // SPEED BRAKE CLOSE VALUE 

Var 0208, name TrWhlNoseUpAP, Value 180 // TRIMWHEEL NOSE UP AutoPilot 

Var 0209, name TrWhlNoseDnAP, Value 70 // TRIMWHEEL NOSE DOWN Autopilot 

Var 0210, name TrWhlNoseUp, Value 220 // TRIMWHEEL NOSE UP 

Var 0211, name TrWhlNoseDn, Value 100 // TRIMWHEEL NOSE DOWN 

Var 0212, name Thr1TOGASpd, Value 100 // THROTTLE 1 TOGA VALUE 

Var 0213, name Thr2TOGASpd, Value 100 // THROTTLE 2 TOGA VALUE 

Var 1982, name throttleman, Link FSUIPC_INOUT, Offset $52FA, Length 2 

Var 1983, name throttleman2, Link FSUIPC_INOUT, Offset $52FC, Length 2 

Var 2000, name Motor_1, Link USB_DCMOTOR, Device 1, Output 1 

Var 2001, name A1, Link USB_ANALOGIC, Device 1, Input 1, PosL 10, PosC 122, PosR 255 
{ 
IF &ATengage <> 0 
{ 
IF &A1 < &potfark 
{ 
IF &toga = 1 
{ 
&Motor_1 = &Thr1TOGASpd 
} 
IF &toga <> 1 
{ 
&Motor_1 = &Thr1FwdSpd 
} 
} 
IF &A1 > &potfark 
{ 
IF &toga <> 0 
{ 
&Motor_1 = &Thr1BckSpd 
} 
} 
IF &A1 < &potplus 
{ 
IF &A1 > &potminus 
{ 
&Motor_1 = 0 
} 
} 
IF &toga = 0 
{ 
&Leverdiscon = 0 
&Motor_1 = 0 
&throttleman = &A1 / 0.016 
} 
IF &toga = 4 
{ 
IF &GALT < 80 
{ 
&Motor_1 = &Thr1RtrdSpd 
&Motor_1 = DELAY 0 ,800 
} 
} 
&A1eski = DELAY &A1 ,50 
&A1fark = &A1 - &A1eski 
&A1fark = ABS &A1fark 
} 
IF &ATengage = 0 
{ 
&throttleman = &A1 / 0.016 
&Motor_1 = 0 
&Leverdiscon = 0 
} 
&angle = &A1 - &A2 
&angle = ABS &angle 
} 

Var 2002, name potfark 
{ 
IF &ATengage <> 0 
{ 
IF &toga <> 1 
{ 
&potfark = &throttlemot * 0.016 
&A1plus = &A1 + 4 
&A1minus = &A1 - 4 
IF &potfark > &A1 
{ 
&Motor_1 = &Thr1FwdSpd 
} 
IF &potfark < &A1 
{ 
&Motor_1 = &Thr1BckSpd 
} 
IF &potfark < &A1plus 
{ 
IF &potfark > &A1minus 
{ 
&Motor_1 = 0 
&Motor_2 = 0 
} 
} 
} 
IF &toga = 4 
{ 
IF &GALT < 80 
{ 
&Motor_1 = &Thr1BckSpd 
&Leverdiscon = 0 
&Motor_1 = DELAY 0 ,800 
} 
} 
} 
IF &potplus > 255 
{ 
&Motor_1 = 0 
} 
} 

Var 2003, name throttlemot, Link FSUIPC_INOUT, Offset $53E0, Length 2 
{ 
IF &throttlemot > 60000 
{ 
IF &IAScalc >= 65 
{ 
IF &spoilerFS <= 4800 
{ 
IF &acongnd = 1 
{ 
&spdbrkMOTOR = DELAY &SpdBrkOpnSpd ,100 
&spdbrkMOTOR = DELAY 0 ,400 
} 
} 
} 
} 
IF &throttlemot < 59000 
{ 
IF &throttlemot > 500 
{ 
IF &spoilerFS > 13000 
{ 
IF &acongnd = 1 
{ 
&spdbrkMOTOR = DELAY &SpdBrkClsSpd ,100 
&spdbrkMOTOR = DELAY 0 ,400 
} 
} 
} 
} 
IF &throttlemot <> &threskideger 
{ 
&trfark = &throttlemot - &threskideger 
&threskideger = DELAY &throttlemot ,20 
&potfark = &throttlemot * 0.0154 
&potminus = &potfark - 8 
&potplus = &potfark + 8 
} 
} 

Var 2004, name threskideger, Value 0 

Var 2005, name potplus 

Var 2006, name trfark 

Var 2007, name potminus 

Var 2009, name ATengage, Link FSUIPC_INOUT, Offset $53E4, Length 1 

Var 2013, name Motor_2, Link USB_DCMOTOR, Device 1, Output 2 

Var 2014, name A2, Link USB_ANALOGIC, Device 1, Input 2, PosL 10, PosC 122, PosR 255 
{ 
IF &ATengage <> 0 
{ 
IF &A2 < &potfark2 
{ 
IF &toga = 1 
{ 
&Motor_2 = &Thr2TOGASpd 
} 
IF &toga <> 1 
{ 
&Motor_2 = &Thr2FwdSpd 
} 
} 
IF &A2 > &potfark2 
{ 
IF &toga <> 0 
{ 
&Motor_2 = &Thr2BckSpd 
} 
} 
IF &A2 < &potplus2 
{ 
IF &A2 > &potminus2 
{ 
&Motor_2 = 0 
} 
} 
IF &toga = 0 
{ 
&Leverdiscon = 0 
&Motor_2 = 0 
&throttleman2 = &A2 / 0.016 
} 
IF &toga = 4 
{ 
IF &GALT < 80 
{ 
&Leverdiscon = 0 
&Motor_2 = &Thr2RtrdSpd 
&Motor_2 = DELAY 0 ,800 
} 
} 
&A2eski = DELAY &A2 ,50 
&A2fark = &A2 - &A2eski 
&A2fark = ABS &A2fark 
} 
IF &ATengage = 0 
{ 
&throttleman2 = &A2 / 0.016 
&Motor_2 = 0 
&Leverdiscon = 0 
} 
&angle = &A1 - &A2 
&angle = ABS &angle 
} 

Var 2015, name potfark2 
{ 
IF &ATengage <> 0 
{ 
IF &toga <> 1 
{ 
&potfark2 = &throttlemot2 * 0.016 
&A2plus = &A2 + 4 
&A2minus = &A2 - 4 
IF &potfark2 > &A2 
{ 
&Motor_2 = &Thr2FwdSpd 
} 
IF &potfark2 < &A2 
{ 
&Motor_2 = &Thr2BckSpd 
} 
IF &potfark2 < &A2plus 
{ 
IF &potfark2 > &A2minus 
{ 
&Motor_1 = 0 
&Motor_2 = 0 
} 
} 
} 
IF &toga = 4 
{ 
IF &GALT < 80 
{ 
&Leverdiscon = 0 
&Motor_2 = &Thr2BckSpd 
&Motor_2 = DELAY 0 ,800 
} 
} 
} 
IF &potplus2 > 255 
{ 
&Motor_2 = 0 
} 
} 

Var 2016, name throttlemot2, Link FSUIPC_INOUT, Offset $53E2, Length 2 
{ 
IF &throttlemot2 > 60000 
{ 
IF &IAScalc >= 65 
{ 
IF &spoilerFS <= 4800 
{ 
IF &acongnd = 1 
{ 
&spdbrkMOTOR = DELAY &SpdBrkOpnSpd ,100 
&spdbrkMOTOR = DELAY 0 ,400 
} 
} 
} 
} 
IF &throttlemot2 < 59000 
{ 
IF &throttlemot2 > 500 
{ 
IF &spoilerFS > 13000 
{ 
IF &acongnd = 1 
{ 
&spdbrkMOTOR = DELAY &SpdBrkClsSpd ,100 
&spdbrkMOTOR = DELAY 0 ,400 
} 
} 
} 
} 
IF &throttlemot2 <> &threskideger2 
{ 
&trfark2 = &throttlemot2 - &threskideger2 
&threskideger2 = DELAY &throttlemot2 ,20 
&potfark2 = &throttlemot2 * 0.0154 
&potminus2 = &potfark2 - 8 
&potplus2 = &potfark2 + 8 
} 
} 

Var 2017, name threskideger2, Value 0 

Var 2018, name potplus2 

Var 2019, name trfark2 

Var 2020, name potminus2 

Var 2021, name Leverdiscon, Link FSUIPC_OUT, Offset $310A, Length 1 

Var 2026, name spdbrkMOTOR, Link USB_DCMOTOR, Device 1, Output 5 

Var 2027, name spoilerARM, Link FSUIPC_INOUT, Offset $0BCC, Length 4 

Var 2028, name spoiler, Link FSUIPC_INOUT, Offset $626F, Length 2 

Var 2030, name spoilerFS, Link FSUIPC_INOUT, Offset $0BD0, Length 4 

Var 2032, name flappos, Link FSUIPC_INOUT, Offset $0BDC, Length 4 

Var 2033, name trim, Link FSUIPC_INOUT, Offset $0BC0, Length 2 
{ 
&trimeski = DELAY &trim ,20 
&trimfark = &trim - &trimeski 
} 

Var 2034, name toga, Link FSUIPC_INOUT, Offset $53E4, Length 1 

Var 2036, name A1plus 

Var 2037, name A1minus 

Var 2038, name A2plus 

Var 2039, name A2minus 

Var 2040, name trimmotor, Link USB_DCMOTOR, Device 1, Output 3 

Var 2041, name trimeski 

Var 2042, name trimfark 
{ 
IF &trimfark > 30 
{ 
&trimmotor = &TrWhlNoseDn 
&trimmotor = DELAY 0 ,400 
} 
IF &trimfark < -30 
{ 
&trimmotor = &TrWhlNoseUp 
&trimmotor = DELAY 0 ,400 
} 
} 

Var 2043, name trimindmotor, Link USB_DCMOTOR, Device 1, Output 4 

Var 2044, name trimindpot, Link USB_ANALOGIC, Device 1, Input 3, PosL 10, PosC 123, PosR 255 
{ 
IF &trimindpot < &trimcalc 
{ 
&trimindmotor = 35 
} 
IF &trimindpot > &trimcalc 
{ 
&trimindmotor = 150 
} 
IF &trimindpot < &indpotplus 
{ 
IF &trimindpot > &indpotminus 
{ 
&trimindmotor = 0 
} 
} 
&indpotplus = &trimcalc + 3 
&indpotminus = &trimcalc - 3 
} 

Var 2045, name trimindtest, Link FSUIPC_IN, Offset $2EA0, Length 8, Numbers 3 
{ 
L0 = &trimindtest + 66 
L1 = L0 / 1.42 
&trimcalc = L1 
} 

Var 2046, name trimcalc 
{ 
IF &trimindpot < &trimcalc 
{ 
&trimindmotor = 35 
} 
IF &trimindpot > &trimcalc 
{ 
&trimindmotor = 150 
} 
IF &trimindpot < &indpotplus 
{ 
IF &trimindpot > &indpotminus 
{ 
&trimindmotor = 0 
} 
} 
&indpotplus = &trimcalc + 1 
&indpotminus = &trimcalc - 1 
} 

Var 2047, name indpotplus 

Var 2048, name indpotminus 

Var 2049, name acongnd, Link FSUIPC_INOUT, Offset $0366, Length 2 
{ 
IF &acongnd = 1 
{ 
IF &spoilerFS > 4800 
{ 
&spdbrkMOTOR = 120 
&spdbrkMOTOR = DELAY 0 ,100 
} 
} 
IF &acongnd = 1 
{ 
&splrcontMOTOR = 125 
&splrcontMOTOR = DELAY 0 ,300 
} 
} 

Var 2050, name FSIAS, Link FSUIPC_IN, Offset $02BC, Length 4 
{ 
&IAScalc = &FSIAS / 128 
} 

Var 2051, name IAScalc 

Var 2052, name splrcontMOTOR, Link USB_DCMOTOR, Device 1, Output 6 

Var 2053, name angle 

Var 0001, name keys, Link KEYS // variable transfert emulateur clavier ( S 

Var 0003, name IAS, Link FSUIPC_IN, Offset $02BC, Length 4 

Var 0051, name IASpmdg, Link FSUIPC_IN, Offset $6220, Length 2 

Var 1997, name GrdAlt, Link FSUIPC_INOUT, Offset $31E4, Length 4 
{ 
L0 = &GrdAlt / 65536 
&GALT = L0 / 0.305 
} 

Var 1996, name GALT 

Var 1995, name A1eski 

Var 1994, name A2eski 

Var 1993, name A1fark 
{ 
IF &A1fark > 50 
{ 
IF &ATengage <> 0 
{ 
&Leverdiscon = 0 
&throttlemot = &A1 / 0.016 
&Motor_1 = 0 
} 
} 
} 

Var 1992, name A2fark 
{ 
IF &A2fark > 50 
{ 
IF &ATengage <> 0 
{ 
&Leverdiscon = 0 
&throttlemot2 = &A2 / 0.016 
&Motor_2 = 0 
} 
} 
} 

Var 1991, name ParkBrkOfset, Link FSUIPC_INOUT, Offset $0BC8, Length 2 
{ 
IF &ParkBrkOfset = 0 
{ 
&splrcontMOTOR = 250 
&splrcontMOTOR = DELAY 0 ,100 
&splrcontMOTOR = DELAY 120 ,200 
&splrcontMOTOR = DELAY 0 ,300 
} 
} 

Var 1986, name gearcontrol, Link FSUIPC_INOUT, Offset $0BE8, Length 4 
{ 
IF &gearcontrol = 0 
{ 
&splrcontMOTOR = 250 
&splrcontMOTOR = DELAY 0 ,100 
} 
} 




_________________
Howard C. 
B737-800

Back to top
View user's profile Send private message  
 
 
spacer.gif
HowardChristian



Joined: 30 Sep 2016
Posts: 45
Location: Sydney
PostPosted: Fri Oct 26, 2018 11:11 pm    Post subject: REVOLUTION SIM TQ Stab Trim Needle Not Working Reply with quote Edit/Delete this post Delete this post


I forgot to include the Sioc.ini file, attached below. 

[ fichero de configuracion para el SIOC ver. 5.0 ] 
[ Configuration file for SIOC ] 


[************** SIOC ***************] 

[ Nombre asignado al SIOC ] 
[ SIOC name ] 
Name=MAIN_SIOC 

[ Puerto del servidor IOCP ] 
[ IOCP port ] 
IOCP_port=8092 

[ Tiempo de respuesta máximo de los paquetes IOCP ] 
[ IOCP Timeout ] 
IOCP_timeout=3500 

[ Arranque minimizado en la barra ] 
[ Start minimized in tray ] 
Minimized=No 

[ Retraso necesario para las variables toggles (Project Magenta)] 
[ Deley needed for var. toggles (Project Magenta) ] 
Toggle_delay=20 

[ Fichero de configuracion ] 
[ Configuration File ] 
[CONFIG_FILE=F:\Documents and Settings\manolo V\Escritorio\IOCARD DESARROLLO\sioc.lst] 
[Audio Panel pedestal FSX.ssi] 

[CONFIG_FILE=F:\Program Files (x86)\ACP_OCockpitOriginal Script.ssi] 

[CONFIG_FILE=F:\Program Files (x86)\SIOC\sioc.lst] 
[sioc.lst] 
[Config_File= throttleSIMAV_V17.ssi] 
[CONFIG_FILE= throttleSIMAV_V17_Audio panel FSX.ssi] 
[Config_File= throttleSIMAV_V17_Audio panel FSXPC2.ssi] 
[CONFIG_FILE=F:\Program Files (x86)\SIOC\throttleSIMAV_V17.txt Changed 24_02_17 cb.ssi] 
CONFIG_FILE=F:\Program Files (x86)\SIOC\sioc.lst 

[************** VIRTUAL DEVICES ***************] 

[ Habilita recepcion de Dis 
positivos Virtuales yes/no ] 
[ Enable Receive Virtual Devices yes/no ] 
Vdevices_enable=Yes 

[ Tiempo de espera para carga inicial de Dispositivos Virtuales (ms)] 
[ Wait time for load Virtual Devices (ms)] 
Vdevices_wait=2000 

[ Modo Esclavo para SIOC como servidor de dispositivos yes/no ] 
[ Slave mode for SIOC Virtual Devices Server yes/no ] 
Vdevices_slave=No 


[ Host y Puerto del SIOC donde reenviar los Dispositivos ] 
[ SIOC Host/Port to resent Devices ] 
Vdevices_host=192.168.1.5 
Vdevices_port=8092 


[************** MONITOR MODULE ***************] 

[ Desabilitar monitorizacion remota del SIOC ] 
[ Remote monitor disable mode yes/no ] 
Monitor_disable=No 

[ Refresco broadcast monitor (en segundos) ] 
[ Broadcast monitor time (seconds) ] 
Monitor_time=2 


[************** IOCARDS MODULE ***************] 

[ Desactivar el módulo de las IOCards ] 
[ Disable IOCards module ] 
IOCard_disable=No 

[ Divisor de frecuencia para los ejes analogicos (1-999). Retarda la entrega de valores. ] 
[ Frequency divisor for delay the analogic axes. (1-999)] 
Divisor_AD=10 

[------------- CARDS CONFIG -------------] 

[ IOCard Master ] 
[...............] 

[ Spanish : ] 

[ MASTER=(Indice device),(Tipo),(Número de tarjetas),(Número device) ] 

[ Indice Device: Índice usado en la variable SIOC como device, para indicar a que tarjeta se hace referencia ] 
[ Se usa 0 en el caso de que sólo haya una tarjeta y no se tenga en cuenta el número de device, por defecto un script en SIOC cuando no se pone parámetro DEVICE, se hace referencia al índice 0] 

[ tipo = 0 : Emulador de Master Card // OBSOLETO ] 
[ tipo = 1 : Tarjeta Master conectada al puerto paralelo directamente // OBSOLETO ] 
[ tipo = 2 : Tarjeta Master conectada al puerto paralelo mediante cable de compatibilidad // OBSOLETO ] 
[ tipo = 3 : Placa de expansión por puerto paralelo // OBSOLETO ] 
[ tipo = 4 : Tarjeta USBExpansion usada ] 
[ tipo = 5 : Modulo MCP de Opencockpits ] 
[ tipo = 6 : Tarjeta USBOutputs ] 
[ tipo = 7 : Modulo EFIS de Opencockpits ] 
[ tipo = 8 : Modulo Radio COM de Opencockpits ] 
[ tipo = 9 : Modulo Radio NAV de Opencockpits ] 
[ tipo = 10 : Modulo Radio ADF de Opencockpits ] 
[ tipo = 11 : Modulo Radio ATC de Opencockpits ] 
[ tipo = 12 : Modulo Radio Airbus RMP de Opencockpits ] 
[ tipo = 13 : Modulo FMC-737 de Opencockpits ] 
[ tipo = 14 : Tarjeta USBDcmotorPLUS ] 
[ tipo = 15 : Modulo MCP V3 de Opencockpits ] 
[ tipo = 16 : Modulo CRONOMETRO B737 ] 
[ tipo = 17 : Tarjeta USBDimcontrol ] 
[ tipo = 18 : Modulo Audio B737 ] 
[ tipo = 19 : Modulo FIRE ENGINES B737 ] 
[ tipo = 20 : Modulo PEDESTAL B737 ] 


[ Número de tarjetas = Número de placas Master usadas, 1 a 4 para uso de placas de expansión, 1 para conexión de placa Master directa o del Emulador ] 

[ Número de device = 0 en el caso del Emulador o primera tarjeta USB detectada, Dirección del puerto paralelo (por ejemplo $0378), o número de dispositivo USB ] 


[ Un ejemplo de 2 USBExpansion conectadas con 3 y 2 placas Master ] 
[ MASTER=0,4,3,22 ] 
[ MASTER=1,4,2,24 ] 

[ Un ejemplo de conexión a simulador ] 
[ MASTER=0,0,1,0 ] 


[ English : ] 

[ MASTER=(Device index),(Type),(Number of cards),(Device number) ] 

[ Device index : Index used in SIOC variable like device, this is the card used for SIOC sentence ] 
[ Use 0 for only one card, for this value you not need specify Device number. If you not use DEVICE parameter in a definition in SIOC script, the default index used is 0] 

[ type = 0 : Master Card Emulator // OBSOLETE ] 
[ type = 1 : Master Card connected directly to parallel port // OBSOLETE ] 
[ type = 2 : Master Card connected throught compatibility cable to parallel port //OBSOLETE] 
[ type = 3 : Expansion Card connected throught parallel port //OBSOLETE ] 
[ type = 4 : USBExpansion Card used ] 
[ type = 5 : Opencockpits MCP module ] 
[ type = 6 : USBOutputs Card used ] 
[ type = 7 : EFIS module ] 
[ type = 8 : Radio COM module ] 
[ type = 9 : Radio NAV module ] 
[ type = 10 : Radio ADF module ] 
[ type = 11 : Radio ATC module ] 
[ type = 12 : Radio RMP Airbus module ] 
[ type = 13 : FMC-737 module ] 
[ type = 14 : USBDCmotorPLUS Card used ] 
[ type = 15 : MCP V3 module ] 
[ type = 16 : CHRONO B737 module ] 
[ tipo = 17 : USBDimcontrol card used ] 
[ tipo = 18 : Audio B737 module ] 
[ tipo = 19 : FIRE ENGINES B737 module ] 
[ tipo = 20 : PEDESTAL B737 module ] 

[ Number of Cards = Master cards connecteds, 1 to 4 for expansion cards, 1 for a Master card directly connected or Emulator ] 

[ Number of device = 0 for Emulator or first USB card detected, parallel port address, device number for specifies USBexpansion card ] 

[ For example, two USBExpansion cards connected with 3 and 2 Master cards used ] 
[ MASTER=0,4,3,22 ] 

[MASTER=18,18,1,191 HC-This line was without brackets but I've added because lines Starting with MASTER should be deleted.] 

[ For example, use of Master card emulator ] 
[ MASTER=0,0,1,0 ] 

[ Use the first USBExpansion card connected with only one Master Card attached ] 
[ Esta definición es para usar la primera tarjeta USBExpansion que se encuentre instalada que además llevará conectada una placa Master ] 

[MASTER=3,6,1,252] 
[MASTER=0,4,1,0] 
[MASTER=1,18,1,40] 
[MASTER=20,20,2,1055] 
[MASTER=0,18,1,40] 


[ Others Cards / Otras tarjetas ] 
[...............................] 

[ Spanish : ] 

[ Nombre_de_tarjeta=(Indice device),(Número device) ] 

[ Indice Device: Índice usado en la variable SIOC como device, para indicar a que tarjeta se hace referencia ] 
[ Se usa 0 en el caso de que sólo haya una tarjeta y no se tenga en cuenta el número de device, por defecto un script en SIOC cuando no se pone parámetro DEVICE, se hace referencia al índice 0] 

[ Número de device = 0 para usar primera tarjeta USB de este tipo detectada ó número de dispositivo USB ] 


[ English : ] 

[ Name_of_card=(Device index),(Device number) ] 

[ Device index : Index used in SIOC variable like device, this is the card used for SIOC sentence ] 
[ Use 0 for only one card, for this value you not need specify Device number. If you not use DEVICE parameter in a definition in SIOC script, the default index used is 0] 

[ Number of device = 0 for first USB card of this type detected, or device number for a specifies device ] 

[ Ejemplo de dos USBServos en indices 0 y 1, y números de devices 17 y 23 ] 
[ Example of two USBServos for index 0 and 1, and device number 17 and 23 ] 

[ USBServos=0,17 ] 
[USBServos=1,13] 


[USBStepper=0,0] 
[USBKeys=0,0] 
[USBServos=0,0] 
[USBRelays=0,0] 
[USBDCmotor=1,19] 
[USBDCmotor=1,19] 



[ Para los ejes analógicos se usan los números de devices de las tarjetas donde están alojados ] 
[ For analogic axles, you use the device number of cards what allow the axles ] 

[USBAnalogic=1,19] 
[USBAnalogic=1,19] 

[************** FSUIPC MODULE ***************] 

[ Desabilitar lectura de las FSUIPC ] 
[ FSUIPC disable mode yes/no ] 
FSUipcdisable=No 

[ Refresco recepción FSUIPC ] 
[ FSUIPC refresh ] 
FSUipcRefresh=50 


[************** IOCP CLIENTS MODULES ***************] 

[ Retraso para inicializacion una vez conectado el cliente en milisegundos ] 
[ Delay for initialization when client has been connected in mseconds ] 
IOCPini_delay=0 

[************** IOCP CLIENT MODULE #0 ***************] 

[ Desactivar el módulo cliente IOCP ] 
[ Disable IOCP client module ] 
IOCPclient0_disable=No 

[ IP del servidor donde debe de conectar el cliente ] 
[ IOCP client host name ] 
IOCPclient0_host=LOCALHOST 

[ Puerto de envio del protocolo IOCP cliente ] 
[ IOCP client port ] 
IOCPclient0_port=8099 


[************** IOCP CLIENT MODULE #1 ***************] 

[ Desactivar el módulo cliente IOCP ] 
[ Disable IOCP client module ] 
IOCPclient1_disable=No 

[ IP del servidor donde debe de conectar el cliente ] 
[ IOCP client host name ] 
IOCPclient1_host=LOCALHOST 

[ Puerto de envio del protocolo IOCP cliente ] 
[ IOCP client port ] 
IOCPclient1_port=8099 


[************** SOUND MODULE ***************] 

[ Ficheros de sonido ] 
[ Sound Files ] 

[ Desactivar el módulo de sonido ] 
[ Disable Sound module ] 
Sound_disable=No 

[ Volumen general de los sonidos 0-100 ] 
[ Master Volume 0-100 ] 
Volume=100 


[ put '*' first filename for loop Sound ] 
[ anteponer '*' en el fichero para bucle continuo de sonido] 

[ Sound=wav_file,frequency,volume,pan ] 
[ frequency=100 to 100000 0=original -1=current ] 
[ volume=0 to 100, -1=current ] 
[ pan=-100 (left) to +100 (right) 0=center -1=current ] 

[ Sound=Fichero_wav,frecuencia,volumen,balance ] 
[ frecuencia=100 hasta 100000 0=original -1=Por defecto ] 
[ volumen=0 hasta 100 -1=Volumen por defecto ] 
[ balance=-100 (Izquierda) hasta +100 (Derecha) 0=centro -1=Por defecto ] 

[ #1 ] 
Sound=APDis.wav,-1,-1,-1 

[ #2 ] 
Sound=*outermk.wav,-1,-1,-1 

[ #3 ] 
Sound=*hello.wav 

[************** KEYBOARD EMULATOR MODULE ***************] 

[ Nombre exacto de la ventana donde se enviarán las teclas ] 
[ Name of window for key send ] 
[window = "Project Magenta Glass Cockpit - Build 396" ] 

window =a.txt - Bloc de notas 


[ Asignación de teclas ] 
[ assign youe keys ] 

#1=A 
#2=B 
#3=C 
#4=D 
#5=E 
#6=F 
#7=G 
#8=H 
#9=I 
#10=J 
#11=K 
#12=L 
#13=M 
#14=N 
#15=O 
#16=P 
#17=Q 
#18=R 
#19=S 
#20=T 
#21=U 
#22=V 
#23=W 
#24=X 
#25=Y 
#26=Z 
#27=1 
#28=2 
#29=3 
#30=4 
#31=5 
#32=6 
#33=7 
#34=8 
#35=9 
#36=0 
#37=< 
#38=, 
#39=. 
#40=- 
#41=* 
#42=+ 
#43=// 
#44=/0 
#45=/1 
#46=/A 
#47=<T 
#48= 
#49= 
#50= 
#51= 
#52= 
#53= 
#54= 
#55= 
#56= 
#57= 
#58= 
#59= 
#60= 
#61= 
#62= 
#63= 
#64= 
#65= 
#66= 
#67= 
#68= 
#69= 
#70= 
#71= 
#72= 
#73= 
#74= 
#75= 
#76= 
#77= 
#78= 
#79= 
#80= 
#81= 
#82= 
#83= 
#84= 
#85= 
#86= 
#87= 
#88=<a 
#200=B 

[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 10-Aug-16 8:51:52 PM <== ----] 
[USBDCmotor=1,11] 
[USBAnalogic=1,11] 
[MASTER=2,18,1,36] 

[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 15-Aug-16 8:31:40 PM <== ----] 
[USBDCmotor=1,11] 
[USBAnalogic=1,11] 
[MASTER=2,18,1,36] 

[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 15-Aug-16 8:38:15 PM <== ----] 
[USBDCmotor=1,11] 
[USBAnalogic=1,11] 
[MASTER=40,18,1,36] 

[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 15-Aug-16 8:49:46 PM <== ----] 
[USBDCmotor=1,11] 
[USBAnalogic=1,11] 
[MASTER=40,18,1,36] 

[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 24-Oct-16 8:35:33 PM <== ----] 

[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 26/06/2017 11:39:27 PM <== ----] 
[USBDCmotor=1,19] 
[USBAnalogic=1,19] 
[MASTER=21,18,1,21] 

[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 26/06/2017 11:52:10 PM <== ----] 



[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 3/07/2017 6:47:15 PM <== ----] 
[USBDCmotor=1,19] 
[USBAnalogic=1,19] 
[MASTER=40,18,1,21] 

[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 3/07/2017 6:48:36 PM <== ----] 
[USBDCmotor=1,19] 
[USBAnalogic=1,19] 
[MASTER=40,18,1,21] 

[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 3/07/2017 7:00:20 PM <== ----] 
[USBDCmotor=1,19] 
[USBAnalogic=1,19] 
[MASTER=21,18,1,21] 

[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 3/07/2017 7:06:15 PM <== ----] 
[USBDCmotor=1,19] 
[USBAnalogic=1,19] 
[MASTER=21,18,1,21] 

[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 3/07/2017 7:10:03 PM <== ----] 
[USBDCmotor=1,19] 
[USBAnalogic=1,19] 
[MASTER=40,18,1,21] 

[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 3/07/2017 7:17:20 PM <== ----] 
USBDCmotor=1,13 
USBAnalogic=1,13 
MASTER=40,18,1,21 



_________________
Howard C. 

Share this post


Link to post
Share on other sites
Help AVSIM continue to serve you!
Please donate today!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now