Pronto

Hello and thank´s for reading!does the pmdg 737 ngx simulation show smoke around the tires at each touch down??? Or does it depend of the touchdown speed / vertical speed in the moment of touching the runway???RegardsNorbertps.: excuse my bad english please

Hi Leffe,I have started up to read the tutorial and to fly this aircraft much more realistic... but: until today everything works fine, especially when I fly without the joystick-controller, only with the keyboard; in this mode the airborn occurs exactly at VR (app. 146 kts.)?!?!?!?N.

Hi Leffe,yes... for to be honestly I never press TOGA (I´m still a beginner)... I start with F4 on the keyboard or with the powerbotton at the joystick-controller... at once the engine-power increase to app. 100 %, the aircraft runs normaly and the airborne is around 180 kts.!?!?!?RegardsNorbert

Hello all!After using a joystick (wingman by logitech) I have the problem, that the aircraft does the airborn only with more than 180 kts. V1 is 146 kts, flaps 5, trimed!Settings in the joystick-menu for the rudders: full sensitivity, minimum dead / neutral zone.What can I do???RegardsNorbert

Hello,I have set the sensitivity of all rudders max high and the dead/neutral zone min small. Only the dead/neutral zone of the siderudder I have set a little bit more, button to the right.RegardsNorbert

Hi guys,thanks again for your appreciated help!!! Finally - after gambling with the joystick-settings - I can keep the aircraft much easier on the centerline. This is a very very good forum here, all the times I´ve got best help within short time! Much better than the german forums!RegardsNorbert

Hi gentlemen, thanks for help! I have changed the settings and keeping the exact altitude and heading is much easier now. But... I have still problems during the start up! Aircraft is centered on the runway, I don´t touch the joystick... the aircraft start to roll and at once it goes to the right... I touch the joystick and give rudder and now - until the airborn - the aircraft runs left, right, left and so on... zickzacking...What can I do? Changes in the siderudder-settings doesn´t help... no sidewind!RegardsNorbert (excuse my bad english please)

Hello all, when I fly the PMDG 737-800 NGX by hand - using the joystick wingman force 3d - it´s difficult to keep an altitude... very often the needle runs up and down... I have set the sensitivity very low and the "neutral-area" very large (button to the right)... I have to correct the altitude all the times... how can I work more excactly and relaxed with the joystick flying by hand????RegardsNorbert

Hello all!What is the best zoomfactor in the 2D-Cockpit? With factor 1.00 I see at the final approach / touchdown only the ground / rundway, on the other hand I have at the take off sequenze with 1.00 a normal / realistic view? How can I store the 2D-Cockpitvie (ex. 0.40) for the standard-flight?GreetingsNorbert

Hi,I had the same problem and I have fixed it with changes in the fsx.cfgset wideviewaspect from "false" to "true"RegardsNorbert

Hi all,zoom is at 1.00 and it looks realistic... in the fsx.cfg the "wideviewaspect" is set to "true"; before it was on "false"! With false I saw with zoom 1.00 only the surface of the runway an I´ve got a "normal" perspective with zoom 0.30! But also with this configuration the aircraft run to fast for take off... it looked very unrealistic!Excuse my bad english please!Norbert

Hi all,I´m using the ngx 737-800, max wight!

Hi all,after SP1 my Startup-Rolling - until airborne - looks very fast, to fast! I give full power (F4) at once and 2 or 3 sec. later the aircraft is rolling already very very fast... (only in 2d-panel)... on the other hand the speedstrip shows normal increasing speed! What can I do?GreetingsNorbert

Hi,after installing the SP1 I have a new view by the 2d-panel... with zoomfactor 1.00 I can see only the surface of the runway... after turning to zoomfactor 0.30 I get the "normal" usefull view... but: it seems to be, that everything runs much faster...maybe timefactor 4 or more!?!?!RegardsNorbert

Thank´s Jason, I´m going to try that! Greetings Norbert

I "fly" the PMDG 737-800 NGX only with the cursor and AP, no joystick, no mouse. During the flight, after disconnecting the AP, it´s not possible to activate AP again! I know, that I have to set the altitude-ruder to neutral, but I don´t find the position... "5" to make all ruders neutral does not work! What can I do??? Greetings Norbert

Exactly! It sounds a little bit like touching tires...

Hi guys, I´m not kidding... ;-) I had asked JasonG for the soundfile, concerning his post # 13... Thank´s all for help! Greetings Norbert

Ok guys... I believe now, that this sound of the tires is not simulated, because it would not be possible to hear it, inside or outside...for JasonG: tell me what do you hear, what soundfile is it???? ;-) Greetings Norbert

Hmmmm... again... what´s the name of the soundfile???

Ok Gentlemen, thank´s for the help, it´s really the spoiler-sound... so I see, that the squeal of the tires is not simulated!?!?!? Greetings Norbert

Hmmmm... can´t believe, sorry.... :-)How can I arm the spoiler... I´m using only the speedbrake, often already during the finaldescent... N.

Why not??? Check / look for this youtube-video! PMDG 737 NGX Landing Madeira FSX + Trackir 5 (HQ)

Hi Patrick,thank´s for your answer... but it´s not the sound of the spoiler... I´m missing the sound of the touching tires... on many youtube ngx-landing-videos you can hear the squeal of the tires! Greetings Norbert

Hello, now I "fly" the PMDG 737 - 800 NGX since 3 weeks... I enyoy the aircraft but I miss the "Tires squeal" at touch down... on my first flight - without using the fmc - I have heard it, but now - with using the fmc, but flying without the ap after passing the decison hight - I don´t hear the "Tires squeal"; do I land to smooth??? :-)I have tried a few different vs-rates / touchdown speed / wight and so on, but I didn´t hear the "Tires squeal" again! What do I have to do? Greetings Norbert ps.: please excuse my bad school-english, thank´s