Jump to content

jim05

Members
 View Profile  See their activity

  • Content Count

    8

  • Donations

    $0.00 

  • Joined

  • Last visited

Posts posted by jim05

  3. Posted · Edited by jim05

    Hi there…

    till today, I run the following system with MSFS 2020:

    Prozessor (CPU): i9 9900 KS; 5,00 Ghz (edited)
    Arbeitsspeicher (RAM): 32 GB DDR4 3600 MHZ CL16
    Mainboard: Z390 Aorus Xtreme
    Netzteil: BeQuiet Dark Power 1200W
    Gehäuse: Thormax
    Grafikkarte: RTX 4090
    HDD / SSD: 1x 500 GB M.2 SSD; 1x 1 TB M.2 SSD
    3 Beamer Optoma HD29HST
    Windows 10

     

    Since last week, I run MSFS with my homecockpit over a 180 degree curved screen with Immersive Display. My FPS dropped to 15 FPS …
    So I plan to sell my system and go for an Intel i9 13900K, 32 GB DDR5 7200 MHZ, Z790 Mainboard.

    I know, that this question is nonsense, but do you think I can get satisfying FPS with this updated system compared to my actual system?

    And another question…. if I go for a 13900K, which mainboard can you recommend? I think about Gigabyte Z790 Aorus Master or ASUS Z790 Hero Maximus. The aorus master is quite cheaper than the Hero Maxiumus. Or is there a thing I have to observe?

     

     

     

    Thank you really a lot for your help!

    Christian

     

     

     



     

     

  4. Posted

    Thanks BerndB,

    hmm... I also think, that you can‘t reach a great sharpness with full hd projectors.

    But I would like to read runway signs clearly, also if they are „far“ away.

    If I switch to 4 monitors, I plan to put them in that way, that the frames are behind the wooden slats of the windows of my shell. For the 4 monitor setup I think, that Fly Elise Immersive LCD pro should be useful.

     

    best regards,

    christian

  6. Posted

    Hi,

    after hours and hours workflow(Full 737 cockpit with shell, Prosim737), I‘m sad about my result and I don‘t know how to fix it.

     

    I built a 200-degree curved screen (I think accurate :-)) and use 3 3LCD - Projectors (2800 lumens, 10.000:1 contrast, real 1080p) with immersive display. 
    The screen has a length about 6,60m x 1,60m, and the projectors have about 1,65 m distance to the screen. 
    In the projector-settings, I use standard-values. 

    Results:

    - The basic colors of the 3 projectors are different. Of course, I can adjust a little bit by immersive calibration, but you can clearly see crossings between the projectors.

    - The picture itself around the screen is very pixelized and not sharp at all.

     

    So I think very hard about a way to get better and satisfying results. Can you give me some advices?

    - I think about putting 3 new lamps in my projectors. Perhaps I have same basic-colors...?!?

    - Or should I sell my old prohectors and get better ones (I think about the Optoma HD29HST with 4000 lumens and 50.000:1 contrast)

    - Or can you advice me to switch to 55-60‘‘ TVs. I think about put 4 TVs around my cockpit-shell. I think, that the picture should be quite sharp, of course, there are the frames of the tvs...). And A resolution of 4k should be possible.

     
    what should I do now? Which way is the best?

     

    I use 2 1080 TI GPUs with 11GB and an i9 

     

    Thanks a lot!

     

    Regards

    Christian

     

  7. Posted

    Hi Jerome,

    I did so. But I wasn‘t sure if it is good, that the default sceneries are placed ABOVE the FS Global entries. I was afraid, that then the default ones have priority and „overlay“ the FS Global Meshes.

     

  8. Posted · Edited by jim05

    Hi...

    I‘ve purchased FS Global ultimate for p3d v5.

    As you can see:

    insjxzv6.jpg

    ... there are 2 Sceneries for Africa, Europe, South America... ONE from FS Global Ultimate (34-41) and ONE „default“-scenery (24-33). Is it recommended to „disable“ the default scenerys (24-33) or is it ok, if this mentioned sceneries are enabled?

     

    best regards,

    Christian

     

×
×
  • Create New...