AAL1005

Greetings all, When it comes to programming, I'm probably the worst (aside from my 10 month old baby). I have a few Korry switches from Opencockpits, and am trying to get them to hook up with FSX. I can wire the switch parts just fine to my Leo Bodnar card, but not the LED parts. I also have a Pokeys56U that supports outputs just fine, but again with the programming. I'm at a loss. I need at least another 45 Korry switches for my cockpit, but if I can't get them to light up as in the real aircraft, it doesn't make sense. I'm building the Q400 cockpit after the Majestic Simulations Q400. As an example of a switch, there are 2 Intake Door Korry switches. When the battery is on and either GPU is connected or APU is on, the switches (off) will illuminate the lower LED showing "CLOSED". When pressed (on), the CLOSED light goes out. Roughly 10 seconds later, the top LED will turn on showing "OPN" (the amount of time it takes to open and close the little door on the engine). Can anyone help me figure this out? As another hardware question, my Pokeys56U software shows when the Korry is on or off, but the joystick settings in windows doesn't show the button being pressed. Any ideas? Thanks in advance for any help! Jack

Can someone take a look at this error report from LINDA? I had installed both files as required in my modules folder. I was able to program the switches I wanted on my Thrustmaster Warthog as I did for my NGX. There's an error in there about a folder not found, but I checked and the file/folder is where it should be.The problem is that no switches move in my Dash, and when I restart Linda, it comes up with this window: HID Device changed me = 12:33:52 (17:33Z) Starting everything now ... LUA.0: beginning "E:\FSX\Modules\ipcReady.lua" LUA.0: ended "E:\FSX\Modules\ipcReady.lua" LUA.1: LUA.1: [INIT] Loading... LUA.1: Aircraft: MJC8Q400_EGF LUA.1: Aircraft module detected: Majestic Dash8 LUA.0: AivlaSoft library loaded... LUA.0: FSX standard library loaded... LUA.0: IAO library loaded... LUA.0: RealityXP library loaded... LUA.0: A2A MAP library loaded... LUA.0: Loading Majestic Dash8 joysticks config... LUA.0: Module: Majestic Dash8 Started... LUA.0: Ready to go, Captain! LUA.0: LUA.0: [S] Offsets watching list cleared! Advanced Weather Interface Enabled Sim stopped: average frame rate for last 26 secs = 42.4 fps Sim stopped: average frame rate for last 51 secs = 37.5 fps [E] *** LUA Error: cannot open linda-cfg/aircrafts/Majestic Dash8/config-mcp.lua: No such file or directory LUA.0: [S] LVars watching list cleared... LUA.0: [S] FSUIPC logging bit cleared: 2 LUA.0: [S] FSUIPC logging bit cleared: 10 LUA.0: [S] LVars watching list cleared... LUA.0: [S] FSUIPC logging bit cleared: 2 LUA.0: [S] FSUIPC logging bit cleared: 10 LUA.0: [S] FSUIPC logging bit cleared: 6 LUA.0: [S] LVars watching list cleared... LUA.0: [S] FSUIPC logging bit cleared: 2 LUA.0: [S] FSUIPC logging bit cleared: 10 LUA.0: [S] FSUIPC logging bit cleared: 6 Sim stopped: average frame rate for last 2429 secs = 30.5 fps LUA.0: [S] LVars watching list cleared... LUA.0: [S] FSUIPC logging bit cleared: 2 LUA.0: [S] FSUIPC logging bit cleared: 10