The TRIM INDICATOR Needles don't move on my Motorised Revolution Sim TQ. They are stuck at 0 Nose Down position.
The Rudder trim Wheels do operate ok.
Does anyone have any ideas or even a Sioc Test script we could try? (I apologise if this is not the correct forum to post, if necessary could moderator please move)? Copy of the SIOC Script & Sioc.ini below.
// *****************************************************************************
// * Config_SIOC ver 4.01 - By Manuel Velez - www.opencockpits.com
// *****************************************************************************
// * FileName : throttleSIMAV_V17.txt
// * Date : 9/04/2012
Var 0166, name Reverser1, Link USB_ANALOGIC, Device 1, Input 4, PosL 5, PosC 125, PosR 255
{
IF &acongnd = 1
{
&Leverdiscon = 0
&throttleman = &A1 / 0.0154
IF &A1 = 0
{
&throttleman = &Reverser1 * -16
}
}
}
Var 0167, name Reverser2, Link USB_ANALOGIC, Device 1, Input 5, PosL 5, PosC 125, PosR 255
{
IF &acongnd = 1
{
&Leverdiscon = 0
&throttleman2 = &A2 / 0.0154
IF &A2 = 0
{
&throttleman2 = &Reverser2 * -16
}
}
}
Var 0200, name Thr1FwdSpd, Value 45 // THROTTLE 1 FWD VALUE
Var 0201, name Thr1BckSpd, Value 175 // THROTTLE 1 BACK VALUE
Var 0202, name Thr1RtrdSpd, Value 195 // THROTTLE 1 RETARD VALUE
Var 0203, name Thr2FwdSpd, Value 45 // THROTTLE 2 FWD VALUE
Var 0204, name Thr2BckSpd, Value 175 // THROTTLE 2 BACK VALUE
Var 0205, name Thr2RtrdSpd, Value 195 // THROTTLE 2 RETARD VALUE
Var 0206, name SpdBrkOpnSpd, Value 120 // SPEED BRAKE OPEN VALUE
Var 0207, name SpdBrkClsSpd, Value 190 // SPEED BRAKE CLOSE VALUE
Var 0208, name TrWhlNoseUpAP, Value 180 // TRIMWHEEL NOSE UP AutoPilot
Var 0209, name TrWhlNoseDnAP, Value 70 // TRIMWHEEL NOSE DOWN Autopilot
Var 0210, name TrWhlNoseUp, Value 220 // TRIMWHEEL NOSE UP
Var 0211, name TrWhlNoseDn, Value 100 // TRIMWHEEL NOSE DOWN
Var 0212, name Thr1TOGASpd, Value 100 // THROTTLE 1 TOGA VALUE
Var 0213, name Thr2TOGASpd, Value 100 // THROTTLE 2 TOGA VALUE
Var 1982, name throttleman, Link FSUIPC_INOUT, Offset $52FA, Length 2
Var 1983, name throttleman2, Link FSUIPC_INOUT, Offset $52FC, Length 2
Var 2000, name Motor_1, Link USB_DCMOTOR, Device 1, Output 1
Var 2001, name A1, Link USB_ANALOGIC, Device 1, Input 1, PosL 10, PosC 122, PosR 255
{
IF &ATengage <> 0
{
IF &A1 < &potfark
{
IF &toga = 1
{
&Motor_1 = &Thr1TOGASpd
}
IF &toga <> 1
{
&Motor_1 = &Thr1FwdSpd
}
}
IF &A1 > &potfark
{
IF &toga <> 0
{
&Motor_1 = &Thr1BckSpd
}
}
IF &A1 < &potplus
{
IF &A1 > &potminus
{
&Motor_1 = 0
}
}
IF &toga = 0
{
&Leverdiscon = 0
&Motor_1 = 0
&throttleman = &A1 / 0.016
}
IF &toga = 4
{
IF &GALT < 80
{
&Motor_1 = &Thr1RtrdSpd
&Motor_1 = DELAY 0 ,800
}
}
&A1eski = DELAY &A1 ,50
&A1fark = &A1 - &A1eski
&A1fark = ABS &A1fark
}
IF &ATengage = 0
{
&throttleman = &A1 / 0.016
&Motor_1 = 0
&Leverdiscon = 0
}
&angle = &A1 - &A2
&angle = ABS &angle
}
Var 2002, name potfark
{
IF &ATengage <> 0
{
IF &toga <> 1
{
&potfark = &throttlemot * 0.016
&A1plus = &A1 + 4
&A1minus = &A1 - 4
IF &potfark > &A1
{
&Motor_1 = &Thr1FwdSpd
}
IF &potfark < &A1
{
&Motor_1 = &Thr1BckSpd
}
IF &potfark < &A1plus
{
IF &potfark > &A1minus
{
&Motor_1 = 0
&Motor_2 = 0
}
}
}
IF &toga = 4
{
IF &GALT < 80
{
&Motor_1 = &Thr1BckSpd
&Leverdiscon = 0
&Motor_1 = DELAY 0 ,800
}
}
}
IF &potplus > 255
{
&Motor_1 = 0
}
}
Var 2003, name throttlemot, Link FSUIPC_INOUT, Offset $53E0, Length 2
{
IF &throttlemot > 60000
{
IF &IAScalc >= 65
{
IF &spoilerFS <= 4800
{
IF &acongnd = 1
{
&spdbrkMOTOR = DELAY &SpdBrkOpnSpd ,100
&spdbrkMOTOR = DELAY 0 ,400
}
}
}
}
IF &throttlemot < 59000
{
IF &throttlemot > 500
{
IF &spoilerFS > 13000
{
IF &acongnd = 1
{
&spdbrkMOTOR = DELAY &SpdBrkClsSpd ,100
&spdbrkMOTOR = DELAY 0 ,400
}
}
}
}
IF &throttlemot <> &threskideger
{
&trfark = &throttlemot - &threskideger
&threskideger = DELAY &throttlemot ,20
&potfark = &throttlemot * 0.0154
&potminus = &potfark - 8
&potplus = &potfark + 8
}
}
Var 2004, name threskideger, Value 0
Var 2005, name potplus
Var 2006, name trfark
Var 2007, name potminus
Var 2009, name ATengage, Link FSUIPC_INOUT, Offset $53E4, Length 1
Var 2013, name Motor_2, Link USB_DCMOTOR, Device 1, Output 2
Var 2014, name A2, Link USB_ANALOGIC, Device 1, Input 2, PosL 10, PosC 122, PosR 255
{
IF &ATengage <> 0
{
IF &A2 < &potfark2
{
IF &toga = 1
{
&Motor_2 = &Thr2TOGASpd
}
IF &toga <> 1
{
&Motor_2 = &Thr2FwdSpd
}
}
IF &A2 > &potfark2
{
IF &toga <> 0
{
&Motor_2 = &Thr2BckSpd
}
}
IF &A2 < &potplus2
{
IF &A2 > &potminus2
{
&Motor_2 = 0
}
}
IF &toga = 0
{
&Leverdiscon = 0
&Motor_2 = 0
&throttleman2 = &A2 / 0.016
}
IF &toga = 4
{
IF &GALT < 80
{
&Leverdiscon = 0
&Motor_2 = &Thr2RtrdSpd
&Motor_2 = DELAY 0 ,800
}
}
&A2eski = DELAY &A2 ,50
&A2fark = &A2 - &A2eski
&A2fark = ABS &A2fark
}
IF &ATengage = 0
{
&throttleman2 = &A2 / 0.016
&Motor_2 = 0
&Leverdiscon = 0
}
&angle = &A1 - &A2
&angle = ABS &angle
}
Var 2015, name potfark2
{
IF &ATengage <> 0
{
IF &toga <> 1
{
&potfark2 = &throttlemot2 * 0.016
&A2plus = &A2 + 4
&A2minus = &A2 - 4
IF &potfark2 > &A2
{
&Motor_2 = &Thr2FwdSpd
}
IF &potfark2 < &A2
{
&Motor_2 = &Thr2BckSpd
}
IF &potfark2 < &A2plus
{
IF &potfark2 > &A2minus
{
&Motor_1 = 0
&Motor_2 = 0
}
}
}
IF &toga = 4
{
IF &GALT < 80
{
&Leverdiscon = 0
&Motor_2 = &Thr2BckSpd
&Motor_2 = DELAY 0 ,800
}
}
}
IF &potplus2 > 255
{
&Motor_2 = 0
}
}
Var 2016, name throttlemot2, Link FSUIPC_INOUT, Offset $53E2, Length 2
{
IF &throttlemot2 > 60000
{
IF &IAScalc >= 65
{
IF &spoilerFS <= 4800
{
IF &acongnd = 1
{
&spdbrkMOTOR = DELAY &SpdBrkOpnSpd ,100
&spdbrkMOTOR = DELAY 0 ,400
}
}
}
}
IF &throttlemot2 < 59000
{
IF &throttlemot2 > 500
{
IF &spoilerFS > 13000
{
IF &acongnd = 1
{
&spdbrkMOTOR = DELAY &SpdBrkClsSpd ,100
&spdbrkMOTOR = DELAY 0 ,400
}
}
}
}
IF &throttlemot2 <> &threskideger2
{
&trfark2 = &throttlemot2 - &threskideger2
&threskideger2 = DELAY &throttlemot2 ,20
&potfark2 = &throttlemot2 * 0.0154
&potminus2 = &potfark2 - 8
&potplus2 = &potfark2 + 8
}
}
Var 2017, name threskideger2, Value 0
Var 2018, name potplus2
Var 2019, name trfark2
Var 2020, name potminus2
Var 2021, name Leverdiscon, Link FSUIPC_OUT, Offset $310A, Length 1
Var 2026, name spdbrkMOTOR, Link USB_DCMOTOR, Device 1, Output 5
Var 2027, name spoilerARM, Link FSUIPC_INOUT, Offset $0BCC, Length 4
Var 2028, name spoiler, Link FSUIPC_INOUT, Offset $626F, Length 2
Var 2030, name spoilerFS, Link FSUIPC_INOUT, Offset $0BD0, Length 4
Var 2032, name flappos, Link FSUIPC_INOUT, Offset $0BDC, Length 4
Var 2033, name trim, Link FSUIPC_INOUT, Offset $0BC0, Length 2
{
&trimeski = DELAY &trim ,20
&trimfark = &trim - &trimeski
}
Var 2034, name toga, Link FSUIPC_INOUT, Offset $53E4, Length 1
Var 2036, name A1plus
Var 2037, name A1minus
Var 2038, name A2plus
Var 2039, name A2minus
Var 2040, name trimmotor, Link USB_DCMOTOR, Device 1, Output 3
Var 2041, name trimeski
Var 2042, name trimfark
{
IF &trimfark > 30
{
&trimmotor = &TrWhlNoseDn
&trimmotor = DELAY 0 ,400
}
IF &trimfark < -30
{
&trimmotor = &TrWhlNoseUp
&trimmotor = DELAY 0 ,400
}
}
Var 2043, name trimindmotor, Link USB_DCMOTOR, Device 1, Output 4
Var 2044, name trimindpot, Link USB_ANALOGIC, Device 1, Input 3, PosL 10, PosC 123, PosR 255
{
IF &trimindpot < &trimcalc
{
&trimindmotor = 35
}
IF &trimindpot > &trimcalc
{
&trimindmotor = 150
}
IF &trimindpot < &indpotplus
{
IF &trimindpot > &indpotminus
{
&trimindmotor = 0
}
}
&indpotplus = &trimcalc + 3
&indpotminus = &trimcalc - 3
}
Var 2045, name trimindtest, Link FSUIPC_IN, Offset $2EA0, Length 8, Numbers 3
{
L0 = &trimindtest + 66
L1 = L0 / 1.42
&trimcalc = L1
}
Var 2046, name trimcalc
{
IF &trimindpot < &trimcalc
{
&trimindmotor = 35
}
IF &trimindpot > &trimcalc
{
&trimindmotor = 150
}
IF &trimindpot < &indpotplus
{
IF &trimindpot > &indpotminus
{
&trimindmotor = 0
}
}
&indpotplus = &trimcalc + 1
&indpotminus = &trimcalc - 1
}
Var 2047, name indpotplus
Var 2048, name indpotminus
Var 2049, name acongnd, Link FSUIPC_INOUT, Offset $0366, Length 2
{
IF &acongnd = 1
{
IF &spoilerFS > 4800
{
&spdbrkMOTOR = 120
&spdbrkMOTOR = DELAY 0 ,100
}
}
IF &acongnd = 1
{
&splrcontMOTOR = 125
&splrcontMOTOR = DELAY 0 ,300
}
}
Var 2050, name FSIAS, Link FSUIPC_IN, Offset $02BC, Length 4
{
&IAScalc = &FSIAS / 128
}
Var 2051, name IAScalc
Var 2052, name splrcontMOTOR, Link USB_DCMOTOR, Device 1, Output 6
Var 2053, name angle
Var 0001, name keys, Link KEYS // variable transfert emulateur clavier ( S
Var 0003, name IAS, Link FSUIPC_IN, Offset $02BC, Length 4
Var 0051, name IASpmdg, Link FSUIPC_IN, Offset $6220, Length 2
Var 1997, name GrdAlt, Link FSUIPC_INOUT, Offset $31E4, Length 4
{
L0 = &GrdAlt / 65536
&GALT = L0 / 0.305
}
Var 1996, name GALT
Var 1995, name A1eski
Var 1994, name A2eski
Var 1993, name A1fark
{
IF &A1fark > 50
{
IF &ATengage <> 0
{
&Leverdiscon = 0
&throttlemot = &A1 / 0.016
&Motor_1 = 0
}
}
}
Var 1992, name A2fark
{
IF &A2fark > 50
{
IF &ATengage <> 0
{
&Leverdiscon = 0
&throttlemot2 = &A2 / 0.016
&Motor_2 = 0
}
}
}
Var 1991, name ParkBrkOfset, Link FSUIPC_INOUT, Offset $0BC8, Length 2
{
IF &ParkBrkOfset = 0
{
&splrcontMOTOR = 250
&splrcontMOTOR = DELAY 0 ,100
&splrcontMOTOR = DELAY 120 ,200
&splrcontMOTOR = DELAY 0 ,300
}
}
Var 1986, name gearcontrol, Link FSUIPC_INOUT, Offset $0BE8, Length 4
{
IF &gearcontrol = 0
{
&splrcontMOTOR = 250
&splrcontMOTOR = DELAY 0 ,100
}
}
_________________
Howard C.
B737-800
Back to top
HowardChristian Joined: 30 Sep 2016
Posts: 45
Location: Sydney
Posted: Fri Oct 26, 2018 11:11 pm Post subject: REVOLUTION SIM TQ Stab Trim Needle Not Working
I forgot to include the Sioc.ini file, attached below.
[ fichero de configuracion para el SIOC ver. 5.0 ]
[ Configuration file for SIOC ]
[************** SIOC ***************]
[ Nombre asignado al SIOC ]
[ SIOC name ]
Name=MAIN_SIOC
[ Puerto del servidor IOCP ]
[ IOCP port ]
IOCP_port=8092
[ Tiempo de respuesta máximo de los paquetes IOCP ]
[ IOCP Timeout ]
IOCP_timeout=3500
[ Arranque minimizado en la barra ]
[ Start minimized in tray ]
Minimized=No
[ Retraso necesario para las variables toggles (Project Magenta)]
[ Deley needed for var. toggles (Project Magenta) ]
Toggle_delay=20
[ Fichero de configuracion ]
[ Configuration File ]
[CONFIG_FILE=F:\Documents and Settings\manolo V\Escritorio\IOCARD DESARROLLO\sioc.lst]
[Audio Panel pedestal FSX.ssi]
[CONFIG_FILE=F:\Program Files (x86)\ACP_OCockpitOriginal Script.ssi]
[CONFIG_FILE=F:\Program Files (x86)\SIOC\sioc.lst]
[sioc.lst]
[Config_File= throttleSIMAV_V17.ssi]
[CONFIG_FILE= throttleSIMAV_V17_Audio panel FSX.ssi]
[Config_File= throttleSIMAV_V17_Audio panel FSXPC2.ssi]
[CONFIG_FILE=F:\Program Files (x86)\SIOC\throttleSIMAV_V17.txt Changed 24_02_17 cb.ssi]
CONFIG_FILE=F:\Program Files (x86)\SIOC\sioc.lst
[************** VIRTUAL DEVICES ***************]
[ Habilita recepcion de Dis
positivos Virtuales yes/no ]
[ Enable Receive Virtual Devices yes/no ]
Vdevices_enable=Yes
[ Tiempo de espera para carga inicial de Dispositivos Virtuales (ms)]
[ Wait time for load Virtual Devices (ms)]
Vdevices_wait=2000
[ Modo Esclavo para SIOC como servidor de dispositivos yes/no ]
[ Slave mode for SIOC Virtual Devices Server yes/no ]
Vdevices_slave=No
[ Host y Puerto del SIOC donde reenviar los Dispositivos ]
[ SIOC Host/Port to resent Devices ]
Vdevices_host=192.168.1.5
Vdevices_port=8092
[************** MONITOR MODULE ***************]
[ Desabilitar monitorizacion remota del SIOC ]
[ Remote monitor disable mode yes/no ]
Monitor_disable=No
[ Refresco broadcast monitor (en segundos) ]
[ Broadcast monitor time (seconds) ]
Monitor_time=2
[************** IOCARDS MODULE ***************]
[ Desactivar el módulo de las IOCards ]
[ Disable IOCards module ]
IOCard_disable=No
[ Divisor de frecuencia para los ejes analogicos (1-999). Retarda la entrega de valores. ]
[ Frequency divisor for delay the analogic axes. (1-999)]
Divisor_AD=10
[------------- CARDS CONFIG -------------]
[ IOCard Master ]
[...............]
[ Spanish : ]
[ MASTER=(Indice device),(Tipo),(Número de tarjetas),(Número device) ]
[ Indice Device: Índice usado en la variable SIOC como device, para indicar a que tarjeta se hace referencia ]
[ Se usa 0 en el caso de que sólo haya una tarjeta y no se tenga en cuenta el número de device, por defecto un script en SIOC cuando no se pone parámetro DEVICE, se hace referencia al índice 0]
[ tipo = 0 : Emulador de Master Card // OBSOLETO ]
[ tipo = 1 : Tarjeta Master conectada al puerto paralelo directamente // OBSOLETO ]
[ tipo = 2 : Tarjeta Master conectada al puerto paralelo mediante cable de compatibilidad // OBSOLETO ]
[ tipo = 3 : Placa de expansión por puerto paralelo // OBSOLETO ]
[ tipo = 4 : Tarjeta USBExpansion usada ]
[ tipo = 5 : Modulo MCP de Opencockpits ]
[ tipo = 6 : Tarjeta USBOutputs ]
[ tipo = 7 : Modulo EFIS de Opencockpits ]
[ tipo = 8 : Modulo Radio COM de Opencockpits ]
[ tipo = 9 : Modulo Radio NAV de Opencockpits ]
[ tipo = 10 : Modulo Radio ADF de Opencockpits ]
[ tipo = 11 : Modulo Radio ATC de Opencockpits ]
[ tipo = 12 : Modulo Radio Airbus RMP de Opencockpits ]
[ tipo = 13 : Modulo FMC-737 de Opencockpits ]
[ tipo = 14 : Tarjeta USBDcmotorPLUS ]
[ tipo = 15 : Modulo MCP V3 de Opencockpits ]
[ tipo = 16 : Modulo CRONOMETRO B737 ]
[ tipo = 17 : Tarjeta USBDimcontrol ]
[ tipo = 18 : Modulo Audio B737 ]
[ tipo = 19 : Modulo FIRE ENGINES B737 ]
[ tipo = 20 : Modulo PEDESTAL B737 ]
[ Número de tarjetas = Número de placas Master usadas, 1 a 4 para uso de placas de expansión, 1 para conexión de placa Master directa o del Emulador ]
[ Número de device = 0 en el caso del Emulador o primera tarjeta USB detectada, Dirección del puerto paralelo (por ejemplo $0378), o número de dispositivo USB ]
[ Un ejemplo de 2 USBExpansion conectadas con 3 y 2 placas Master ]
[ MASTER=0,4,3,22 ]
[ MASTER=1,4,2,24 ]
[ Un ejemplo de conexión a simulador ]
[ MASTER=0,0,1,0 ]
[ English : ]
[ MASTER=(Device index),(Type),(Number of cards),(Device number) ]
[ Device index : Index used in SIOC variable like device, this is the card used for SIOC sentence ]
[ Use 0 for only one card, for this value you not need specify Device number. If you not use DEVICE parameter in a definition in SIOC script, the default index used is 0]
[ type = 0 : Master Card Emulator // OBSOLETE ]
[ type = 1 : Master Card connected directly to parallel port // OBSOLETE ]
[ type = 2 : Master Card connected throught compatibility cable to parallel port //OBSOLETE]
[ type = 3 : Expansion Card connected throught parallel port //OBSOLETE ]
[ type = 4 : USBExpansion Card used ]
[ type = 5 : Opencockpits MCP module ]
[ type = 6 : USBOutputs Card used ]
[ type = 7 : EFIS module ]
[ type = 8 : Radio COM module ]
[ type = 9 : Radio NAV module ]
[ type = 10 : Radio ADF module ]
[ type = 11 : Radio ATC module ]
[ type = 12 : Radio RMP Airbus module ]
[ type = 13 : FMC-737 module ]
[ type = 14 : USBDCmotorPLUS Card used ]
[ type = 15 : MCP V3 module ]
[ type = 16 : CHRONO B737 module ]
[ tipo = 17 : USBDimcontrol card used ]
[ tipo = 18 : Audio B737 module ]
[ tipo = 19 : FIRE ENGINES B737 module ]
[ tipo = 20 : PEDESTAL B737 module ]
[ Number of Cards = Master cards connecteds, 1 to 4 for expansion cards, 1 for a Master card directly connected or Emulator ]
[ Number of device = 0 for Emulator or first USB card detected, parallel port address, device number for specifies USBexpansion card ]
[ For example, two USBExpansion cards connected with 3 and 2 Master cards used ]
[ MASTER=0,4,3,22 ]
[MASTER=18,18,1,191 HC-This line was without brackets but I've added because lines Starting with MASTER should be deleted.]
[ For example, use of Master card emulator ]
[ MASTER=0,0,1,0 ]
[ Use the first USBExpansion card connected with only one Master Card attached ]
[ Esta definición es para usar la primera tarjeta USBExpansion que se encuentre instalada que además llevará conectada una placa Master ]
[MASTER=3,6,1,252]
[MASTER=0,4,1,0]
[MASTER=1,18,1,40]
[MASTER=20,20,2,1055]
[MASTER=0,18,1,40]
[ Others Cards / Otras tarjetas ]
[...............................]
[ Spanish : ]
[ Nombre_de_tarjeta=(Indice device),(Número device) ]
[ Indice Device: Índice usado en la variable SIOC como device, para indicar a que tarjeta se hace referencia ]
[ Se usa 0 en el caso de que sólo haya una tarjeta y no se tenga en cuenta el número de device, por defecto un script en SIOC cuando no se pone parámetro DEVICE, se hace referencia al índice 0]
[ Número de device = 0 para usar primera tarjeta USB de este tipo detectada ó número de dispositivo USB ]
[ English : ]
[ Name_of_card=(Device index),(Device number) ]
[ Device index : Index used in SIOC variable like device, this is the card used for SIOC sentence ]
[ Use 0 for only one card, for this value you not need specify Device number. If you not use DEVICE parameter in a definition in SIOC script, the default index used is 0]
[ Number of device = 0 for first USB card of this type detected, or device number for a specifies device ]
[ Ejemplo de dos USBServos en indices 0 y 1, y números de devices 17 y 23 ]
[ Example of two USBServos for index 0 and 1, and device number 17 and 23 ]
[ USBServos=0,17 ]
[USBServos=1,13]
[USBStepper=0,0]
[USBKeys=0,0]
[USBServos=0,0]
[USBRelays=0,0]
[USBDCmotor=1,19]
[USBDCmotor=1,19]
[ Para los ejes analógicos se usan los números de devices de las tarjetas donde están alojados ]
[ For analogic axles, you use the device number of cards what allow the axles ]
[USBAnalogic=1,19]
[USBAnalogic=1,19]
[************** FSUIPC MODULE ***************]
[ Desabilitar lectura de las FSUIPC ]
[ FSUIPC disable mode yes/no ]
FSUipcdisable=No
[ Refresco recepción FSUIPC ]
[ FSUIPC refresh ]
FSUipcRefresh=50
[************** IOCP CLIENTS MODULES ***************]
[ Retraso para inicializacion una vez conectado el cliente en milisegundos ]
[ Delay for initialization when client has been connected in mseconds ]
IOCPini_delay=0
[************** IOCP CLIENT MODULE #0 ***************]
[ Desactivar el módulo cliente IOCP ]
[ Disable IOCP client module ]
IOCPclient0_disable=No
[ IP del servidor donde debe de conectar el cliente ]
[ IOCP client host name ]
IOCPclient0_host=LOCALHOST
[ Puerto de envio del protocolo IOCP cliente ]
[ IOCP client port ]
IOCPclient0_port=8099
[************** IOCP CLIENT MODULE #1 ***************]
[ Desactivar el módulo cliente IOCP ]
[ Disable IOCP client module ]
IOCPclient1_disable=No
[ IP del servidor donde debe de conectar el cliente ]
[ IOCP client host name ]
IOCPclient1_host=LOCALHOST
[ Puerto de envio del protocolo IOCP cliente ]
[ IOCP client port ]
IOCPclient1_port=8099
[************** SOUND MODULE ***************]
[ Ficheros de sonido ]
[ Sound Files ]
[ Desactivar el módulo de sonido ]
[ Disable Sound module ]
Sound_disable=No
[ Volumen general de los sonidos 0-100 ]
[ Master Volume 0-100 ]
Volume=100
[ put '*' first filename for loop Sound ]
[ anteponer '*' en el fichero para bucle continuo de sonido]
[ Sound=wav_file,frequency,volume,pan ]
[ frequency=100 to 100000 0=original -1=current ]
[ volume=0 to 100, -1=current ]
[ pan=-100 (left) to +100 (right) 0=center -1=current ]
[ Sound=Fichero_wav,frecuencia,volumen,balance ]
[ frecuencia=100 hasta 100000 0=original -1=Por defecto ]
[ volumen=0 hasta 100 -1=Volumen por defecto ]
[ balance=-100 (Izquierda) hasta +100 (Derecha) 0=centro -1=Por defecto ]
[ #1 ]
Sound=APDis.wav,-1,-1,-1
[ #2 ]
Sound=*outermk.wav,-1,-1,-1
[ #3 ]
Sound=*hello.wav
[************** KEYBOARD EMULATOR MODULE ***************]
[ Nombre exacto de la ventana donde se enviarán las teclas ]
[ Name of window for key send ]
[window = "Project Magenta Glass Cockpit - Build 396" ]
window =a.txt - Bloc de notas
[ Asignación de teclas ]
[ assign youe keys ]
#1=A
#2=B
#3=C
#4=D
#5=E
#6=F
#7=G
#8=H
#9=I
#10=J
#11=K
#12=L
#13=M
#14=N
#15=O
#16=P
#17=Q
#18=R
#19=S
#20=T
#21=U
#22=V
#23=W
#24=X
#25=Y
#26=Z
#27=1
#28=2
#29=3
#30=4
#31=5
#32=6
#33=7
#34=8
#35=9
#36=0
#37=<
#38=,
#39=.
#40=-
#41=*
#42=+
#43=//
#44=/0
#45=/1
#46=/A
#47=<T
#48=
#49=
#50=
#51=
#52=
#53=
#54=
#55=
#56=
#57=
#58=
#59=
#60=
#61=
#62=
#63=
#64=
#65=
#66=
#67=
#68=
#69=
#70=
#71=
#72=
#73=
#74=
#75=
#76=
#77=
#78=
#79=
#80=
#81=
#82=
#83=
#84=
#85=
#86=
#87=
#88=<a
#200=B
[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 10-Aug-16 8:51:52 PM <== ----]
[USBDCmotor=1,11]
[USBAnalogic=1,11]
[MASTER=2,18,1,36]
[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 15-Aug-16 8:31:40 PM <== ----]
[USBDCmotor=1,11]
[USBAnalogic=1,11]
[MASTER=2,18,1,36]
[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 15-Aug-16 8:38:15 PM <== ----]
[USBDCmotor=1,11]
[USBAnalogic=1,11]
[MASTER=40,18,1,36]
[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 15-Aug-16 8:49:46 PM <== ----]
[USBDCmotor=1,11]
[USBAnalogic=1,11]
[MASTER=40,18,1,36]
[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 24-Oct-16 8:35:33 PM <== ----]
[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 26/06/2017 11:39:27 PM <== ----]
[USBDCmotor=1,19]
[USBAnalogic=1,19]
[MASTER=21,18,1,21]
[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 26/06/2017 11:52:10 PM <== ----]
[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 3/07/2017 6:47:15 PM <== ----]
[USBDCmotor=1,19]
[USBAnalogic=1,19]
[MASTER=40,18,1,21]
[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 3/07/2017 6:48:36 PM <== ----]
[USBDCmotor=1,19]
[USBAnalogic=1,19]
[MASTER=40,18,1,21]
[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 3/07/2017 7:00:20 PM <== ----]
[USBDCmotor=1,19]
[USBAnalogic=1,19]
[MASTER=21,18,1,21]
[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 3/07/2017 7:06:15 PM <== ----]
[USBDCmotor=1,19]
[USBAnalogic=1,19]
[MASTER=21,18,1,21]
[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 3/07/2017 7:10:03 PM <== ----]
[USBDCmotor=1,19]
[USBAnalogic=1,19]
[MASTER=40,18,1,21]
[ --- SIOC Autoconfig Devices Ver 5.0 B5 ==> 3/07/2017 7:17:20 PM <== ----]
USBDCmotor=1,13
USBAnalogic=1,13
MASTER=40,18,1,21
_________________
Howard C.