Thrunkx

TBM 900 with full clickable GTN 750 + Original Engine Avionics TBM 900 with DUAL full clickable GTN 750 + Original Engine Avionics Hi again, this time I made the calculation for my TBM 900, I made a few flights and all was working fine! Use The xplane11 key command "Autopilot VOR/LOC Arm" to activate the Autopilot NAV mode, the standart command from X-aviation is not working by me. Full clickable GTN 750, right click to trigger the GTN popup Engine Avionics at the left, left click to trigger the G1000 popup Use the button number 12 in the bottom right to start the Engine avionics on the MFD after a few seconds when all Avionics are powered up ______________________________________________________________________________________________________________________ 1. Start in The Xplane11/Aircraft folder, make a copy from your TBM900 folder, rename it "TBM-900_GTN". 2. Start Xplane11, load your new made TBM900 and when loaded, start GTN750-1 just to create the RealityXP.GTN.ini, exit Xplane11 3. Go to the new created TBM900_GTN folder, edit the TBM900_cockpit.obj, start a search for "Popup" and delete this 2 lines: ATTR_manip_command button tbm900/popups/mfd_keypad Show/Hide MFD keypad popout window ATTR_manip_command button tbm900/popups/mfd Show/Hide MFD popout window Dont forget to save:-) 4. Edit the RealityXP.GTN.ini and Copy/Paste my calculation code down here: ______________________________________________________________________________________________________________________ TBM 900 with DUAL full clickable GTN 750 + Original Engine Avionics <<< Im flying with this setup Two full clickable GTN 750, right click on GTN1 to popup the GTN1 window and right click on GTN2 to popup the GTN2 window Engine Avionics at the left, left click to trigger the G1000 popup Use the button number 12 in the bottom right to start the Engine avionics on the MFD after a few seconds when all Avionics are powered up _______________________________________________________________________________________________________________________ The installation is the same as above with one difference: 2. Start Xplane11, load your new made TBM900 and when loaded, start GTN750-1 and GTN750-2 just to create the RealityXP.GTN.ini, exit Xplane11 Here my calculation Code for the DUAL GTN 750: ________________________________________________________________________________________ This one was a hard piece of work:-) I hope it works for you all to. Have fun!

Hi there, go here: Best regards

Carenado C90 with GTN750 -- GTN 1 + GTN 2 full clickable Hi There, I m doing some calculations to my Fleet to Adapt GTN 750 , gonna post from time to time some results here, hope it helps. GTN1 Frame rect =540,1872,550,394 GTN2 Frame rect =657,1014,432,240 Here my RealityXP.GTN code for the Carenado C-90:

S-92 Sikorsky wiith full clickable GTN1 GTN2 My How To calculate Frame rect, I hope it helps. Display position and dimension (left,top,width,height) _____________________________________________________________ 1. Use X plane 11 key command "make a panel screenshot" and shoot a screenshot from your Aircraft. 2. Go to your Xplane11/aircraft Folder. 3. Select the Aircraft folder you want to calculate with that made screenshot 4. In your selected Aircraft folder goto Subfolder Cockpit_3d/-Panels- 5. Open the Panel_Preview.png with the Windows Paint program. 6. In the Bottom left from Paint you can see the coordinates from your mouse pointer. 7. Take the coordinates from Top Left and Bottom Right where you want to put the GTN's 8. In Paint you can see the resolution in the bottom midle from the Panel_Preview.png screenshot to calculate the "Top" Value. 9. Use the values that you Take from Paint to calculate the Frame rect. 10. Edit your Frame rect calculation in your Aircraft Main folder in the RealityXP.GTN.ini (by [GTN_750_1.PANELS] for GTN1) and ([GTN_750_2.PANELS] for GTN2) How To calculate Frame rect: _____________________________________________________________ Left = Top left Value from X Top = Screenshot Resolution from Paint -MINUS- Y from Top left Width = X from Bottom Right -MINUS- X from Top Left Height = Y from Bottom Right -MINUS- Y from Top Left Frame rect = Left,Top,Width,Height _____________________________________________________________ Example how i calculate for my S-92 Sikorsky: (my Panel_Preview.png resolution was 1024) GTN1 Calc Top Left: X= 115 Y= 50 Bottom Right: X= 337 Y= 320 Frame rect =115,974,222,270 (left,top,width,height) ----------------------- GTN2 Calc Top Left: X= 9 Y= 499 Bottom Right: X= 336 Y= 813 Frame rect = 9,525,327,314 (left,top,width,height) ______________________________________________________________ Delete the Panel_Preview.png bevor you make a new screenshot for a new calculation. Here my Code from the RealityXP.GTN.ini for the S-92 Sikorsky:

GTN750 for X-Rotors AW139 V4 (alternate) Hi there Again:-) Here the code for the same of my last post but with GTN1 at the left panel and GTN2 at the right Fms. My RealityXP.GTN.ini code:

GTN750 for X-Rotors AW139 V4 Hi there, I Calculate this: GTN1 at the front right panel, not clickable because the original panel stills in background, i just use the GTN1 Popup to change values. GTN2 at the right Fms, full clickable. How to: Start Xp11 and load GTN1 and GTN2 in your AW139 this will create the custom RealityXP.GTN.ini in your AW139 main folder. then close Xp11 and go to your main folder from the AW139 in Xplane11/Aircraft/AW139 Edit the RealityXP.GTN.ini, delete the standart code and copy/paste my Calculation code down here, Dont forget to save:-) Start xplane 11 and try it, I hope it works for you to. When there is some problems. just delete the RealityXP.GTN.ini and all is standart again. My RealityXP.GTN.ini code: _________________________________________________________________