I read all the posts and still can't get an rte file to load into the FMC. I generated the file using FSBuild 2,;Flight Plan Generated by Fsbuild 2.0 KRDU-KBNAH,KRDU,KBNA, ,W,LIB,PACKK5,30,35.811500,-79.612600,113.000000,0.000000,0,0,0,0W,AZELL,,0,35.859300,-80.240100,0.000000,0.000000,0,0,0,0W,HMV,,0,36.437000,-82.129500,114.600000,0.000000,0,0,0,0W,SOT,,0,35.790100,-83.052300,108.800000,0.000000,0,0,0,0W,VXV,,0,35.902000,-83.891500,116.400000,0.000000,0,0,0,0W,BAMMA,VOLLS5,30,35.684800,-85.198700,0.000000,0.000000,0,0,0,0W,VANDD,VOLLS5,30,35.556500,-85.919800,0.000000,0.000000,0,0,0,0W,VOLLS,VOLLS5,30,35.682000,-86.084000,0.000000,0.000000,0,0,0,0End of FlightPlanWhen I enter the filename KRDUKBNA ( the actual filename is KRDUKBNA.rte) and select CO ROUTE, the hard drive cranks for about a minute but nothing shows in the FMC. I can enter data manually and the rte file is in the fs2000pmdgflightplans folder. Anyone have any suggestions?MachToo:-zhelp

HiThis does not seem to be the right format for a PMDG flightplan. It looks more like a PIC flightplan. Unfortunately I'm not using FSBuild so I can't help you out but check your settings in FSBuild and try again.Hope it helps,

An FsBuild 2 generated PMDG 737NG flight plan looks like this.WilliamPMDG737NGFMC15KATL1DIRECT1 N 33.6404 W 84.4269 1026 27R11 N 33.6347 W 84.4089 1026 11026--1000000-1000000KIMMS2DIRECT1 N 33.6346 W 84.5429 0 000PONKE2DIRECT1 N 33.6343 W 84.748 0 000VUZ2J521 N 33.6702 W 86.8998 0 000IGB5J521 N 33.4855 W 88.5136 0 000SQS5J521 N 33.4639 W 90.2773 0 000SUTTN5J521 N 33.5058 W 92.3648 0 000WOOTN5J521 N 33.511 W 92.9158 0 000TXK2J1311 N 33.5139 W 94.0732 0 000FUZ2J41 N 32.8894 W 97.1794 0 000ABI5J41 N 32.4813 W 99.8635 0 000INK5J41 N 31.8748 W 103.244 0 000CONNE5J41 N 31.9342 W 105.329 0 000EWM2-1 N 31.9517 W 106.272 0 000KELP1-1 N 31.8067 W 106.378 3958 2201 N 31.8228 W 106.37 3958 13958--1000000-1000000

That's the 767PIC format, not the 737NG.They have the same extension '.rte', but the formats are completely different.Regards.Ernie.

OK, so since FSBuild does not have a 737NG format to select what is everyone using to generate the flightplans?Thanks,Dean

They do i use fsbuild 1.43 and 737NG on the list left side rigt before PMDG 757, i check mark 737NG when i save.see jpegHasan

Thanks. I use FSBuild 2.0. I found out in the FSBuild forum that a beta version is being tested that has the 737NG format. So, I requested it last night.