Upgraded to 2.9.0.8 today. Using P3D3v5.1 but in the sim it can't access any of the commands or the checklists for any of the aircraft.. I have uninstalled and installed several times. Worked fine in 2.9.07 and all previous MCEs

1 hour ago, daveep said:

Upgraded to 2.9.0.8 today. Using P3D3v5.1 but in the sim it can't access any of the commands or the checklists for any of the aircraft.. I have uninstalled and installed several times. Worked fine in 2.9.07 and all previous MCEs

Which fsInsider64.dll do you have inside \Prepar3D v5\ installation folder?

Can you post a screenshot of the MCE user interface? Thanks

 

i am using p3dv5.1 and all prior versions have worked fine.

https://www.dropbox.com/s/r0s933c2jry97ig/General Tab.PNG?dl=0 hope you can see this.

fsinsider64.dll 2.9.0.4 565kb

Thank you for any help you can provide.

Edited March 31, 20215 yr by daveep

8 hours ago, daveep said:

i am using p3dv5.1 and all prior versions have worked fine.

https://www.dropbox.com/s/r0s933c2jry97ig/General Tab.PNG?dl=0 hope you can see this.

fsinsider64.dll 2.9.0.4 565kb

Thank you for any help you can provide.

Thanks

Screenshot looks OK and I take it you deliberately disabled the <Checklist> feature, therefore, cannot request checklist reading.

Go to <About> tab and check "Sound In" and "Sound Out" are on the devices you expect.

Could you elaborate on this "can't access any of the commands or the checklists"

Do you mean speech commands not taken in or actual access to various tabs?

I assume MCE is installed to default C:\Program Files (x86)\Multi Crew Experience\ folder.

 

Thank you for your assistance.

I did not disable the Checklist feature. In fact I cannot enable it.

The <About> Tab shows the correct "Sound in" and "Sound Out" are correct and the ones I have always used.

When I go to the <Command> Tab there are zero of my "Flows"

I can communicate with FO  and he will execute some generic commands "set 128.70 on comm one" but non of the Flows for any of my Aircraft are visible nor does the FO recognize any of them.

MCE is installed to C:\Program Files (x86)\Multi Crew Experience\ folder.

Also MCE takes a very long time to load as if it is searching for the Aircraft's content

I have been updating since 2019 without problem..

https://www.dropbox.com/s/s096m8s7c2j0xlk/VoxScript Overview.PNG?dl=0

https://www.dropbox.com/s/3yb7i8r5t2zg85f/Sim Tab.PNG?dl=0

I love the product. Let me know if additional information is needed.

7 hours ago, daveep said:

Thank you for your assistance.

I did not disable the Checklist feature. In fact I cannot enable it.

The <About> Tab shows the correct "Sound in" and "Sound Out" are correct and the ones I have always used.

When I go to the <Command> Tab there are zero of my "Flows"

I can communicate with FO  and he will execute some generic commands "set 128.70 on comm one" but non of the Flows for any of my Aircraft are visible nor does the FO recognize any of them.

MCE is installed to C:\Program Files (x86)\Multi Crew Experience\ folder.

Also MCE takes a very long time to load as if it is searching for the Aircraft's content

I have been updating since 2019 without problem..

https://www.dropbox.com/s/s096m8s7c2j0xlk/VoxScript Overview.PNG?dl=0

https://www.dropbox.com/s/3yb7i8r5t2zg85f/Sim Tab.PNG?dl=0

I love the product. Let me know if additional information is needed.

Matter is being investigated.

Meanwhile, since the potential issue could be in fsInsider64.dll (revised ecently), do you have a package that last worked OK for you?

If you do, unzip it and open <Resources> folder.

Copy older fsInsider64.dll and paste it to \Prepar3D v5\ folder.

 

I found fsinsider64,DLL 2.8.8.5 in a prior version and put it in the Sim and things appear to be working as normal now. The 2.9.0.4 version was in the Sim when not working. However  also found a version 2.9.0.0. Should I give it a try or leave well enough alone?

Thank you for your prompt support. It is much appreciated. Thank you.

Edited March 31, 20215 yr by daveep

32 minutes ago, daveep said:

I found fsinsider64,DLL 2.8.8.5 in a prior version and put it in the Sim and things appear to be working as normal now. The 2.9.0.4 version was in the Sim when not working. However  also found a version 2.9.0.0. Should I give it a try or leave well enough alone?

Thank you for your prompt support. It is much appreciated. Thank you.

You're welcome.

Had an e-mail with an issue that appears to be similar from a French guy who confirmed he had to go back toV2.9.0.0.

You could actually install the very latest V2.9.0.8 (version refers to "mce.exe") and just replace "fInsider64.dll" with the one that ships in V2.9.0.0

It is affecting P3D V5.1 only.

 

FYI. Tried V2.9.0.0 which did not work. Reverted back to V2.8.8.5 which does.

Thanks for your help.

1 hour ago, daveep said:

FYI. Tried V2.9.0.0 which did not work. Reverted back to V2.8.8.5 which does.

Thanks for your help.

Thanks for feedback.

This new dll should settle things in V5.1

Not tested yet using P3D Hotfix eleased today.

Confirm all OK now. Should also see an entry under <Add-ons> menu to start MCE.