Jump to content

John Regan

Members
  • Content Count

    37
  • Donations

    $0.00 
  • Joined

  • Last visited

Community Reputation

0 Neutral

Contact Methods

  • Website URL
    http://
  • ICQ
    0

Profile Information

  • Gender
    Male
  • Location
    Myrtle Beach,SC

Flight Sim Profile

  • Commercial Member
    No
  • Online Flight Organization Membership
    none
  • Virtual Airlines
    Yes
  1. Yes of course, it's little ol me... I emailed you :)

  2. Cathy from Lexington? If so, you can email me @ jregan68@gmail.com

  3. Hey John, Remember me??? Cathy

  4. Andy,There is one 737NG panel that I found here on Avsim. Do a search for Paul Scarratt and the PS Panels 737NG panel will show up. I personally think it if the best freeware panel out there.John
  5. Have you changed the .air or .cfg files for this aircraft. I changed these files not to long ago and had error messages whenever I tried to load the loadedit program. Changing them back to the default fixed the problem.John
  6. Just an update. I went back to FSUIPC 3.12 and all my problems disappeared. Has anyone else had any problems with 3.53?Thanks,John
  7. Thanks, I did that several times. I received an email from the developers and they said to switch to an earlier version of FSUIPC. I was using 3.53 and switched back to 3.12 which was the last version I was using. Well, everything works perfectly now and I couldn't be happier. Thanks to everyone who offered advice!!Thanks,John
  8. >I am curious why you're using shortcut keys rather than>mousing on the buttons. Have you tried it that way? I have>no idea what CTRL-H is supposed to do, btw.CRTL-H is mapped by default to MCP HDG selector pull. I have tried using the keyboard shortcut and mousing the knobs. I was using the keyboard shortcut because that is the way the tutorial is written and I didn't want to leave something out by mistake.>What cruise flight level do you have programmed in the MCDU? >And did you load page 2 of the init with block fuel etc?The cruise flight level is set at FL310 and the ZFW and fuel block were set correctly. I was using the CYYZ-KORD tutorial because I thought I was overlooking something and I wanted to make sure the fault wasn't something I was ommiting either due to programming or system management. >Regards>>Bob Scott>ATP IMEL Gulfstream II-III-IV-V L-300>Santiago de Chile>If you can suggest anything else, I'll give it a try.Thanks again,John
  9. Thanks for the help. I tried everything which you suggested. No luck. I have sent an e-mail to the developers and I am just waiting for a response. I was hoping that someone else had this problem and thus a solution. If you have anymore suggestions, I'll give them a try.Thanks again,John
  10. Well, I tried loading the default cessna at KSEA. Then loaded the PSS A330. Then changed to CYYZ as per the tutorial. After start-up of engines and programming the FMC as per the tutorial, I proceeded to take off. Pressed the crtl-h key then the z key. Altitude was set at 5000 ft and displayed in blue on the PFD. I was at 2200 ft when I pressed the z key. The plane wouldn't climb as it should. I fear that I might have to do a re-install but as I am on dial-up, I dread the time it will take. Do you have anymore suggestions before I take the plunge?Thanks again,John
  11. Thanks Bob. I haven't thought of that (the "z" key). I'll give it a try and let you know.
  12. >>In FSUIPC (registered) on the technical page make sure>"Discon>>Elev axis for A/P" is NOT checked.>>This is what upset the A320 for me some time ago when I>changed the setting to accomodate the Feelthere/PIC 737. As>soon as I switched on AP, the aircraft nose dived. Forgot to>switch it back.>>Tony Thanks Tony for replying back. I have tried just about everything and I am about to pull my hair out. A week ago, the A330 functioned perfectly. The only change I made to MSFS is the upgrade th FSUIPC 3.53. I have gone back to 3.47 and even 3.12 and deleted the FSUIPC .ini file each time. Still no luck.John
×
×
  • Create New...