Kilopapa

Hi, I use the left handle of my CH Flight Throttle Quadrant (Axis X) as "Spoiler handle" (MSFS). The axis is recognised but, as in the real a/c, the spoilers should be deployed by moving the handle down from top to buttom. But it does not work. The top position means full spoilers, the lowest postion results in zero spoilers. Of course I tried checking the box "Axis Reverted", but there is no change. How can get it work the right way? Regards

Hi, I have tried over and over again, but it does not work. Avsim says "login or password is incorrect", which is not, happens only with OCI. I have have reinstalled and changed default web app from FF to chrome, still no change. Any idea? Regards [Edit:] Disregard, my mistake. I always logged into the main webpage but not the filebase.

Thanks, but I have deactivated all controllers in P3D because I prefer using FSUIPC. And as far as I can see the button in question is not assigned to any FSUIPC command or P3D action. Anway there must be an "AP disconnect" command somewhere. I hope to somehow figure out what is behind that. Greetings to B.C. 🙂

Hi all, I use CP with Q400 and created four presets for my favorite views (Pilot/FO/Overhead/Pedestrial). This works fine when selecting the presets from the CP GUI by mouse clicks. But I usually control my presets by using four buttons of an hardware controller, which are all set up by selcting "Assign Buttton". This configuration works fine for all P3D addons. Except for the Dash which does not like the use of buttons because each time I change the view the Autopilot disconnects. I have doublechecked the button assignments within FSUIPC, but there are no conflicts. Changing the views manually by panning and zooming works fine as well. Effects are on "0". Does anyone have an idea? [Edit: Found out only one button causes the problem. I deleted the assignment for that one but it still disconnects the AP.] Best regards Kp

Hi, download link broken? An error occurred. Sorry, the page you are looking for is currently unavailable. Please try again later.

Have you really tried it? It is not working here. According to Pilot's forum a new version for Prepar3D v4 needs to be released.

Got it working Not too complicated actually, :smile:

Thanks. So I will keep on trying although I have failed to so far .

For some reasons I currently use Prepa3D v. 2.5 and v.3.3 (both are installed on same PC). Is it possible to install 777 for both versions? It appears the installer only manages one installation per one PC and copying folders/files vom \Prepar3D v.2 to \Prepar3D v.3 does not really work. Best regards Kilopapa

Hello, I had the same problem again some hours later on that flight. Again there was a strong (but *steady*) crosswind (100+ kts). I use P3D 2.4 and FSGRW and never had an issue like this before with any other addon (like Aerosoft A319-321, LevelD 767 or others). Judging from that I doubt it could be a FSGRW issue. Seemed more like an overreaction to the wind input. What was puzzling me most was that even HDG SEL did not react the way it usually does. So I had a hard time getting the plane somehow back on course. I am aware it's almost impossible to find out what was going on just by posting the issue but I find it useful to share my experience with the developing team. Anymway I saved the situation, could that help? I am very happy by the way it happend in simulator. Wouldn't have been funny bouncing off and on a NAT track with 'the real thing'. :o

Hi, after 4 hours enroute time EDDK - KMIA my 777 suddenly stops following the NAT route. Somtime after 5130N the plane starts banking heavily turning 90° to the right, than back, overshooting and the same to the left. It even does not follow HDG SEL immediatly but takes 1 or up to 2 minutes to finish the turn and to eventually follow the selected heading. Headwind is steady with 60 kts (before 90 kts) from the left. Disconnecting A/P or inserting the waypoint again as direct to did not help. Never had this issue before. Could it be a LNAV issue?