BillStewart

Been having this issue randomly and can't figure it out. Basically when game is loading (Steam version) the blue progress bar gets to 85% and just hangs. Causing me to shut down msfs and try again. It then asks me if I want to load in safe mode or normal. I then click normal and most times it loads correctly. Has anyone had this issue and if so, is there a solution? I'm using the addon linker program if that helps. Thanks Bill

same here

thank you,,I figured it out by saving as an App. It's an option in Microsoft Edge.

Hello, I just purchased this to use with PMDG 737 in MSFS 2020. I can connect fine to it but when I try to activate full screen mode, it does it no problem, but then every few seconds it goes back into window mode. Then a few seconds later it goes back into full screen mode and then repeats the cycle. Has anyone experienced this and if so, is there a fix? I'm using MS Edge, but also tried Chrome. FYI, I can stay in full screen mode for web surfing. Thanks Bill

thank you. I'll try again and get back to you.

thank you. I'll definitely try that next time.

Hello, was flying the PMDG 737 and had to step away so I hit escape key and selected load from PC (I read that pauses the pmdg plane). Anyway I came back 15 mins later and fps were at around 9fps. Before pause, fps were 84 or so. so I just shut the sim down. I'm on a 13700, rtx 4080. ultrawide monitor, 32mb ram, using fstl. Has anyone had this issue?

So I tried same flight and same issue. Basically I flew star, then ATC says to descend to 17000. (about 40 miles out) then I'm 5 miles out and it says to descend to 15000, then in same sentence it says descend to 5000 and then 3000 with two heading changes and cleared for ILS approach. This doesn't seem right to me. I should be stepping down way sooner. Obviously I couldn't get down in time and to circle until altitude is at 3k for ILS approach.

Hello, new user here. I just flew a simbrief plan from KIAD to KJFK. ATC directed me to 22L to land but only asked me to descend down to 7000 ft by the time I was a few miles from the airport. Obviously, there wasn't enough time/distance to get down to 3000 which is what the ILS chart said I should be at. Is there a setting I need to select to get this changed so I get down to a much lower altitude earlier in the approach phase? hanks Bill

awesome thank you!

thank you for replying so quickly. It sounds like I need to know on my own which is the active runway to request vectors to? I asked ATC for weather at that airport and it told me everything with the exception of the active runways. So, is it up to me to determine that based on the winds provided by ATC? If I tuned in the ATIS frequency, would that have given me active runways? Thanks

I just purchased P2ATC the other day and have been slowly trying to figure it out. A few questions: I've noticed that when I read back atc instructions on the ground, i get no response, however if I use SAY IT after the voice says it, atc responds with readback correct. I'm reading from the same box and yet I get nothing. ATC seems to understand my requests. Sometimes I'll read back clearance instructions and the controller will respond with just altitude and squawk code, almost like it didn't understand me originally. I'll repeat just those two pieces, but still no atc response. Also, I did a flight from KPIT to KPHL and was using a simbrief ifr flight plan. I decided after 10 mins after takeoff that I wanted to land in Harrisburg (KMDT). I couldn't figure out how to have ATC guide me there. I was looking through the grammar files and found "request clearance to xxxx airport. I did that, and received a clearance, but as I approached, it didn't give me any instructions to vector for landing. How am I supposed to go about having ATC direct me to land at an airport that was not in the original flight plan. Thank you Bill

ok, thank you for the quick response!

Hi, trying this out and I requested taxi to runway, I get it and when I try to read it back myself or even use the say it option, I never get a readback correct. I get nothing. Is this a user error issue? Thanks Bill

thanks for the response. I'll try again, but when I select a gate, my flight plan changes to direct. I load up the flight and when i turn on the g1000, it shows a direct flight path instead of my original created in simbrief with various waypoints.