nosecone

Thank you, email sent Regards Rhys

Hi all I have saved a switch on my joystick for the water drop but everytime a launch firefighter x I have to go back into settings and select the button config and re save am I doing something wrong Cheers Rhys

Hi Launched Firefighter x today, connected OK, but when I went to settings I got the error message window unhandled exception. I haven't add this error before when clicking on settings button Below is the is the details Anyone able to help as I need to get into the settings menu Cheers Rhys

Posted in wrong section Sorry Rhys

Hi all I have the freeware MD500e Originally designed Peter Tamas Helicopter and updated for fsx. The issue is the weather is effecting engine start. In bad weather using the default weather themes I have to twist my throttle fully open for the engine to spool up which takes longer than usual to start. In fine weather engine spools up with normal throttle settings. Cheers Rhys

Hi allI have been looking for TOT(turbine outlet temp) gauge for my MD500E that has analogue needle and digital read out. After searching I found the closest gauge that fits the description but it is an ITT(inlet Turbine temp) gauge from a Dash 8 Q300. I have installed the gauge into my panel which shows up but doesn't work.It it possible to convert the gauge so it works as TOT and not an ITT gauge.Any help would be very much appreciatedRegardsRhys

Hi all I'm looking for a TOT (turbine outlet temperature) gauge with the analog needle combined with the digital readout. Does anyone know any freeware aircraft that has one Cheers Rhys

Hi Thanks for the quick reply much appreciated I assume I have the non beta version of fsx se I will re install LLTX . I run the program as administrator when I launch live traffic not sure if that's makes a difference Thanks once again Rhys

Hi Yes had that un ticked some time ago for another program I have the steam version of fsx and the se version of live traffic Rhys

Hi all Just out of interest how long should the pause screen be on after connected LLTX I have noticed that on some occasions I have to use task manager to shut down LLYX as nothing seems to be happening Cheers Rhys

Thank you I will delete the the ai helicopter that my simulator is based on I did have an issue with the pause screen staying on after LLYX connected but found if I run as administrator it that fixed it Cheers Rhys

Hi all I have recently found and downloaded live traffic and its a great free addon. I do have a little issue that I can't explain I have a Helicopter cockpit and have a starter on my collective. when using live traffic when I start my heli for some reason the N2 needle doesn't want to move pass the 20% and I have to twist the collective throttle to almost max to get the engine going. WIth live traffic not active I can push and hold the collective start and the needle slowly moves pass 20% to 63% and then I twist the throttle to reach 103% as it should I know live traffic is a independent program but I am scratching my head as to why it would cause this issue Cheers Rhys

Hi all I'm Looking for any ex hovercontrol members who may be able to help or any one who could help I am looking for some old files from hovercontrol They are Scarcreekloads2 and liftableloads If anyone could help please let me know Regards Rhys

Hi There is an android app call FS radio panel free and pro version. Uses you tablet to display radio com1/com2 nav1/nav2 ADF transponder, Great app has other instruments you just need to download panel server and your good to go Rhys

Hi all. I would like to add some default liftable items for my helicopter. I saw you can use ai carriers 2 and place objects where you like. I have ai carriers installed but how do I add objects to ai carriers so I can select them and place them where I like Cheers Rhys

Hi allI'm trying to breath some life into my fsx se and my helicopter cockpit by adding liftable objects. I have looked at the early Slingloads in the Sandboxliftable missions which was done along time ago.My cockpit is based on a MD500e. so I'd liked to use that to setup some very basic items to lift and move around.In the sling loads missions there were about 30 liftable items and 2 helicopters the bell 206 and the EH-101. The bell could only pick up one item which was the stretcherI would like just a few small generic items to move around. I have object placement tool installed so I am able to create my own scenery using the default scenery objects and I know that liftable objects need to be setup as missionsIs there any other downloadable objects that I could use to create missions for litable objects CheersRhys

Hi all I want to remove a particular sound from my aircrafts cockpit I have a full scale MD500e cockpit and have assigned real switches to control various functions One switch I have turns on the battery, but in the real MD when turning on the battery there is no noise I have removed the battery Sound file from the folder and in the sound cfg removed the lines that pertain to the battery sound but when restart my flight and switch on the battery I still get the battery noise. Not sure what I have missed ? Regards Rhys

Thanks mate looks like what I'm after Thank you Rhys

Hi I am looking at adding an agricultural spray effect to a specific aircraft I have I'm currently using 1 but looking for a more realistic effect with a thinner trail Cheers Rhys

Hi all Im looking for a thin white smoke effect to add to one of my aircraft. The default one is to thick for that I am trying to achieve and wondering if anyone knows of one that I could download either as a separate file or already in aircraft that I could place in the effects folder and put in my aircraft cfg Cheers Rhys

Hi allI want to set up a custom view for the cockpit of my helicopter. I want to look out the left side and down to simulate looking at an under slug load.I have moved my eye point to the view I want. I want to be able to replace the default views so when I cycle through the views I have just the virtual cockpit and my custom view.Question isWhere do I enter the coordinates of the new view and what sections do I delete to only cycle through the two views I wantRegardsRhys

Thanks Aron Done issue sorted mistake on my part Regards Rhys

Hi all I have an issue with my saved flight. I have saved my flight in the virtual cockpit and ticked this as my default flight . When I launch my flight my view start from the tail boom not the virtual cockpit. I have gone back to the virtual cockpit and overwritten the file but my flights still start from the tail boom not the virtual cockpit . Regards Rhys

Hi Propwash Do you have any more info on the GoogleEarth View which uses the earth desktop. I have the plugin which no longer works on chrome and really enjoyed flying in GE view Cheers Rhys

Hi all when I start my helicopter, the blades just seem spool up to full rotation when I atcivate the fuel switch. Is there anyway with the default helicopters to start so the blades turn slowly at first and then build up to full rotation. Cheers Rhys