A320SimPilot

Hello, at regular intervals my Keyboard bindings are not working and i have to toggle the simmconnect button so as to regain normal operation. The strange thing is that the bindings of my 2 other hardware are not affected and are always available Sorry if this has been asked and answered before

Ok, found it (L:AaoButtonLayer) 1 == for Yellow. Thanks a lot!

Hello. I had the same issue. I followed your guide and put all the keyboard combos to the yellow layer and kept all joystick ones to the default. I have also a "aao_button_layer_up" combo so as to switch between the default and the yellow I have made a small guage that i want it to be visible when the yellow is active. Unfortunately the value (L:AaoLayerYellow) 1 == does not work. Is this the correct value? What am i doing wrong? Thanks in advance

I understand your thought process, thanks. My biggest issue was when i was switching to the second computer's monitor on the right, MSFS got out of focus and fps adaptation was enabled. I had to put it very low (at 20) but in the end this was like having no fps adaptation at all. In the meanwhile, and between my message and your reply, i have found a solution to my case For anyone that uses 2 pc's with one mouse/keyboard and the "mouse without borders" software, the option is the "hide mouse at screen edge". You untick it on your MSFS pc and MSFS remains in focus even if you go to the second computer. Hope this helps!

Hello. I believe there is an issue with people (like me) who use FG and a single monitor. Whenever i want to put the LOD program forward, MSFS goes out of focus, fps drop and i come very close to fps adaptation limit. I don't have a high end system. 3800x with 3060 ti and a 60hz monitor. I have it locked to 55. I don't know what fps to set for adaptation that will not trigger it when msfs goes out of focus Thank you for your time

Works perfectly. No issues at all Thanks again!!!

Yesssss I have spoilers now, i am approaching for landing. Will let you know if there is an issue with the disarming Thank you so much!!!

Thank you for this. I installed it during cruise but unfortunately I have brakes while in the air. I have to wait to land and see if i will have spoilers (the opposite from what i want) To answer your question, no i don't ... brakes and spoilers work automatically upon touchdown in the A320, you just have to arm them 🙂

Hello Can I make a double assignment on a joystick axis where only one of the two is energized depending on whether a condition is met or not? For example, i would like to assign brakes and spoilers to my joystick axis. Brakes on the ground (AGL 0 or near 0) and spoilers when AGL>0. Is this possible?

Ok, forgive my limited knowledge. I am trying to do this but i am a little confused I want to run a script when the button is pressed. the button has the following LVAR: S_OH_CALLS_MECH the script i want to run is" mygroup-mymechscript What is MY_S_OH_CALLS_MECH ? 🙂

I agree with you. I believe the best combination for stutter free and visual quality on the ground is low TLOD and high OLOD. In the air high LOD and maybe keep OLOD untouched... I am flying at this moment with these settings and perfromance is really good

So, its essential on the ground and irrelevant in the air, right?

Thank you very much for your effort! Same for me with 0.3.7 PC Mode and FG active MSFS 1.36.20 I have a question. I watched a YT video and this guy said to change the OLOD values and put them in the opposite direction (higher on the ground and lower as we climb). While it makes some sense, i am sure there is a catch, since noone else has mentioned it. What is your opinion about this?

Yes, i want to use the "mech" or "fwd" calls buttons on the overhead panels of the Fenix A320.

Hello Is it possible to run a script by clicking with the mouse? I have made scripts for voice controlling GSX. I call mechanic and stewardes by using the voice control function along with audio files for their replies. I can activate their response by making a script for the mech and fwd cabin buttons and assigning it to my hardware. My question is, can i initiate their response by actually clicking calls button on the overhead panel? Thanks in advance