Rman

Guys, Thanks for the help. I was able to get it to work. I downloaded & unzipped the files to a different location and it worked as expected. Again, thanks for the help and great customer service. Regards, Bob

I have downloaded it three times and it still receive the error message. I am a longtime user and have never had this problem before. Thanks again for your prompt response. Regards, Bob

The GTN Database 1909 fails to install. I get the following error message 'A file that is required cannot be installed because the cabinet file H:\DBsl.cab has an invalid digital signature. This may indicate that the cabinet file is corrupt.' Please advise. Regards, Bob

Tom, Thank you for responding. Yes, I am referring to the X-Trident Bell 412 and I have set the options REALITYXP 1. Unfortunately, this has not corrected the problem. I was wondering if there is a way to disable the X-Plane 530? Another thought is that the GTN 750 settings are causing the conflict. Regards, Bob

I was wondering if someone could help me with my GTN 750 autopilot? I am flying the AB-412 Helicopter which comes equipped with the X-Plane 530. The problem that I am experiencing is that when I create a flight plan in the GTN 750, the only way that I can get it to track the active leg is to select the OBS key on the X-Plane 530. The Helicopter will track the current leg to the waypoint but will not fly to the next waypoint in the plan unless I select the OBS key on the X-Plane 530 again. In fact, I must do this with every waypoint throughout the entire plan, if not the Helicopter veers off course and fly’s around aimlessly. I am not sure if it is a setting issue with the GTN 750, or the AB-412 Helicopter. Any help would be greatly appreciated. Regards, Bob

I have discovered what my issues was with the F-35A. When loading the aircraft, the X-Plane G1000 is hidden. I must open the G1000 and delete the previous flight plan that was stored. After deleting the G1000 flight plan I must ensure that the Major device is selected on the GTN1. Then I can build the flight plan in the Reality XP GTN and it works as expected. Regards, Bob

I just purchased and installed the F-35A. It comes equipped with the X-Plane G1000. Unfortunately, while flying with the GTN 750 the LOC must be selected at every waypoint or it will not follow the flight plan. Additionally, If I disable the GTN 750 and try using the X-Plane G1000 I cannot change the NAV SOURCE in order to capture the ILS. Normally, I would re-enable the GTN 750; touch the CDI key to toggle navigation source and disable the GTN 750 again. Unfortunately, this not only does not work, it deletes the X-Plane G1000 flight plan. I have reviewed the RealityXP support forum and discovered similar issues regarding the X-Plane G1000, but no recommendations on how to remedy the problem. Additionally, I have studied the RXP GTN 750/650 Touch User’s Manual For X-Plane and have concluded I am too simple minded to find a solution on my own. If anyone has a better grasp of the configuration concepts or some insight, I could really use your help. Regards, Bob

I recently upgraded my hard drive to a SSD. Unfortunately, when i open RXP GTN 750 in X-Plane i get a Invalid License Message and the GTN 750 locks up. Could someone please help me out? Regards, Bob

Thanks for the prompt response. Regards, Bob

While flying the Carenado S550 Citation; using the RXP GTN 750 I am unable to get the V NAV to fly the altitude constraints as indicated in the flight plan. When I disable the GTN 750 and instead use the stock X-Plane FMS the V NAV works fine. Is this plane capable of flying V NAV with the GTN 750? Regards, Bob

DavidP, Thanks for the prompt response. Regards, Bob

Is there a way to switch from VNAV to VCALC in V2.5.4? I really enjoyed the VCALC feature and canot figure out how to switch from the new VNAV. Regards, Bob