I just completed successfully my first flight with the 767-300 and complete hardware control with what I have for now! (MCP + Pedestal)So, ladies... (huh?) and Gentlemen... (applause...)Here they are!The required entries for FSBUS (ver2.2) to allow control of the LevelD 767 with the use of Nico Kaan's FSCONV translator.To make the entries available in FSBUS you have to add the following lines into the FSIF.INI file found in the FSBUS folder.Be sure to make a backup first!Also, you CANNOT use Project Magenta and the Level D 767 at thesame time as FSCONV uses the PM FSUIPC offset range to translate the panel data.After you have copied these definitions to the FSIF.ini file, (FSBUS must NOT be running), you can select any of the available entries as a flight simulator destination.The definitions are also attached as text file for easy save.George DorkofikisAthens, Greecehttp://www.ldsflyingclub.com/lsd1.jpghttp://www.precisionmanuals.com/images/forum/betaimg.jpg# Lvl, Name ID Mode Offset Type Opt flags scan mul div#----------------------------------------------------------------------0, "LevelD 767"1, "Overhead"1, "MCP/AFDS"2, "Buttons & Swithes" ,560, 0,0x0530, I32, 0, W , 1,1,3, "Left A/P CMD switch" ,562, 0, 0, BIT, 0, W , 1,1,3, "Center A/P CMD switch",563, 0, 0, BIT, 1, W , 1,1, 3, "Right A/P CMD switch" ,564, 0, 0, BIT, 2, W , 1,1, 3, "IAS/MACH selector" ,565, 0, 0, BIT, 3, W , 1,1, 3, "Speed Intervention" ,566, 0, 0, BIT, 4, W , 1,1, 3, "N1 button" ,567, 0, 0, BIT, 5, W , 1,1, 3, "SPD button" ,568, 0, 0, BIT, 6, W , 1,1, 3, "ALT HOLD button" ,569, 0, 0, BIT, 7, W , 1,1, 3, "HDG HOLD button" ,570, 0, 0, BIT, 8, W , 1,1, 3, "HDG SEL button" ,571, 0, 0, BIT, 9, W , 1,1, 3, "LNAV button" ,572, 0, 0, BIT,10, W , 1,1, 3, "VNAV button" ,573, 0, 0, BIT,11, W , 1,1, 3, "FLCH button" ,574, 0, 0, BIT,12, W , 1,1, 3, "BCRS button" ,575, 0, 0, BIT,13, W , 1,1, 3, "LOC button" ,576, 0, 0, BIT,14, W , 1,1, 3, "APP button" ,577, 0, 0, BIT,15, W , 1,1, 3, "VS button" ,578, 0, 0, BIT,16, W , 1,1,2, "Autopilot Disengage" ,579, 0,0x0534, I8, 0, W , 1,1, 2, "Captain FD" ,580, 0,0x0535, I8, 0, W , 1,1, 2, "Autothrottle Arm" ,581, 0,0x0536, I8, 0, W , 1,1, 2, "F/O FD" ,582, 0,0x0537, I8, 0, W , 1,1, 2, "MCP Altitude" ,583, 0,0x0538, I16, 0, RW+, 10,1,1, 2, "MCP Heading" ,584,13,0x053A, I16, 0, RW+, 10,1,1, 2, "MVP Vert Speed" ,585, 0,0x053C, S16, 0, RW+, 10,1,1, 2, "MCP IAS speed" ,586, 0,0x053E, I16, 0, RW+, 10,1,1, 2,"MCP Flags" ,587,0,0x04FA,I8 , 0, R , 1,1, 3, "Flightdirector" ,588,0, 0,BIT, 0, R , 1,1, 3, "F/O FD" ,589,0, 0,BIT, 1, R , 1,1, 3, "Left autopilot" ,590,0, 0,BIT, 2, R , 1,1, 3, "Center autopilot" ,591,0, 0,BIT, 3, R , 1,1, 3, "Right autopilot" ,592,0, 0,BIT, 4, R , 1,1, 3, "Speed mode IAS/M" ,593,0, 0,BIT, 5, R , 1,1, 3, "Speed INTV" ,594,0, 0,BIT, 6, R , 1,1, 3, "ALT Capture" ,595,0, 0,BIT, 7, R , 1,1, # 0=OFF, 1=ARMED, 2=HOLD, 3=N1, 4=SPD, 5=FLCH, 6=VNAV, 7=IDLE, 8=TOGA, 9=FAIL2, "Autothrottle Mode" ,596,0,0x0541, I8, 0, R , 10,1,1,# 0=OFF, 1=ALT HOLD, 2=VERT SPD, 3=FLCH, 4=VNAV, 5=GS,6=TO, 7=GA, 8=FLARE2, "Pitch Armed Mode" ,597,0,0x0542, I8, 0, R , 10,1,1,# 0=OFF, 1=ALT HOLD, 2=VERT SPD, 3=FLCH, 4=VNAV, 5=GS, 6=TO, 7=GA, 8=FLARE2, "Pitch Actual Mode" ,598,0,0x0543, I8, 0, R , 10,1,1,# 0=OFF, 1=HDG HOLD, 2=HDG SEL, 3=LNAV, 4=LOC, 5=BC,6=TO, 7=GA, 8=ROLL2, "Bank Armed Mode" ,599,0,0x0544, I8, 0, R , 10,1,1,# 0=OFF, 1=HDG HOLD, 2=HDG SEL, 3=LNAV, 4=LOC, 5=BC,6=TO, 7=GA, 8=ROLL2, "Bank Actual Mode" ,600,0,0X0545, I8, 0, R , 10,1,1,1, "Radios"2, "NAV1 Frequency" , 550, 3, 0x0520, I16, 0, RW+, 10,1,1,2, "NAV1 CRS" , 551,13, 0x0522, I16, 0, RW+, 10,1,1,2, "NAV2 Frequency" , 552, 3, 0x0524, I16, 0, RW+, 10,1,1,2, "NAV2 CRS" , 553,13, 0x0526, I16, 0, RW+, 10,1,1,2, "NAV1 Mode Man/Auto" , 554, 0, 0x0528, I8, 0, W , 10,1,1,2, "NAV2 Mode Man/Auto" , 555, 0, 0x0529, I8, 0, W , 10,1,1,

Excellent work, George!I'll probably be using these for my cockpit, but I'm still not sure if we're switching to IOcards or not :(... Thanks again, the work from you and Nico is much appreciated!br,Tero

Thas great news and great help for us, Fsbus and Lvl-D users,dear GeorgeHard to underastimate your efforts and hard work make possible to connect both of themThanks a lot George, and Nico for your great work and sharing that with us

George,Congrats, well done! Any plans to use the other services of FSCONV as well? There is still more in it to enjoy you know! Such as an almost Complete Overhead panel and the Level-D COMM1 VFR radio with dynamic standby window and Frequency Transfer Switch. By the way: do you have a website where I can refer to for your FSIF.ini file and/or pictures of your implementation.Cheers. Nicowww.nicokaan.nl

For the rest of the services:Oh yes indeed!... For Sure!But I will work through those as I progress.As for a site. Not yet. Feel free to post the FSIF.ini file to your site.Cheers!George DorkofikisAthens, Greecehttp://www.precisionmanuals.com/images/forum/betaimg.jpg

Hello George !Thnxx for a great job ! guess i'm not the only one to enjoy it (-:Menni

George,>As for a site. Not yet. Feel free to post the FSIF.ini file>to your site.Ok, thx, I have put in on my Downloads page.Nicowww.nicokaan.nl