Annoying Cirrus/High Overcast layer

[russianspd 5]

I like what the program does and I am very fond of the instant loading of the METARS. The ONE issue I have been dealing with is an high altitude overcast cloud that follows my plane.

 

I did a flight from LAX-SMF and this cloud would not go away. I tinkered with the settings and was able to somewhat get rid of a portion of the problem by turning off the cirrus clouds.

 

Here's the METAR for my home airport

Weather At Current Location [30,30] 1 METARS

MET QNH: 1017 mb, 30.06 in, Temp: 27/11, Vis: 32000m, Wind: 000/0, Upper 045/63

 

 

Here is a picture of the cloud:

 

This was taken at my local airport, the sky outside is completely clear say for this false overcast layer.

 

Here's another example at KSAN. The METAR says it's clear but yet again, this alienship layer.

 

 

Aside from this one issue, I think this program definitely outdoes the other top competitors.

 

Thanks

[ZKOKQ 871]

It is called the cloud of doom.

From the Faq available at the Official F1 Opus forum.

 

I get a consistent static cloud layer that forms above the aircraft

Make sure you have disabled your 3rd party weather engines and in addition disabled/removed all their visibility, haze and fog effects. You must replace the cirrus_overcast03.bmp file within your flight simulator's Texture folder as follows,

1. Navigate to your simulator's texture folder, either <FSX>\Texture or <Prepar3D>\Texture

2. Rename your cirrus_overcast03.bmp file to cirrus_overcast03_foggy.bmp.

3. Truncate our cirrus_overcast03_Opus_1024.bmp filename to cirrus_overcast03.bmp.

4. Restart your FSX or P3D simulator.

If you still have problems then repeat the above exercise using our 512 bitmap.

[russianspd 5]

Will report back in about 5 mins. Thanks for the quick reply.

[mosteen 111]

Hm, I have never seen this, I use REXE textures, does that eliminate this phenomena?

[russianspd 5]

Fixed. Thank you very much.

 

Hm, I have never seen this, I use REXE textures, does that eliminate this phenomena?

Actually. I compiled my route in REX Essential Plus and loaded the textures and then started FSX and then OPUS and had the issue with the cloud. So for me, this came WITH the rex textures. But the solution worked.

[Kosta 122]

Actually. I compiled my route in REX Essential Plus and loaded the textures and then started FSX and then OPUS and had the issue with the cloud. So for me, this came WITH the rex textures. But the solution worked.

 

Where did you get the REX Essential Plus?

[mosteen 111]

Ok, thanks, I'll check it out. It has been overcast and fog were I have been flying lately so I guess I did not get a chance to observe this.

[russianspd 5]

Ok, thanks, I'll check it out. It has been overcast and fog were I have been flying lately so I guess I did not get a chance to observe this.

Can you confirm the METAR for your area reporting clear? If it is reporting clear skies and you are getting the follow me cloud than the above solution should work for you as it did for me.

 

Where did you get the REX Essential Plus?

lol sorry i've been readin all day about PLUS and it's coming out. Had it on the mind. I am using REX Essentials.

[ZKOKQ 871]

Hm, I have never seen this, I use REXE textures, does that eliminate this phenomena?

It is not the REX/FEX/AS2012 textures that cause this, it is the associated weather engines. In AS2012 you must un tick fog layer, before using Opus.

[mosteen 111]

Oki, now I get it, I never used the REXE WX, just poured in the textures and let Opus rip, did not start REXE anymore after that