November 8, 201411 yr This just started recently, everything was fine before for a long time. Now I get the Unable to Load Gauge warning, The gauge is ILH_TCAS.gau and the whole VSI gauge on the panel is gone. Can anyone help?
November 11, 201411 yr Sounds like maybe the gauge file got corrupted. I'd start by replacing it with an archived copy. Regards Bob Scott | President and CEO, AVSIM Inc ATP Gulfstream II-III-IV-V Sys1 (MSFS20+24/XPlane12+11): AMD 9800X3D, water 2x240mm, MSI MPG X670E Carbon, 64GB GSkill 6000/30, nVidia RTX4090FE Alienware AW3821DW 38" 21:9 GSync, 2x4TB Crucial T705 PCIe5 + 2x2TB Samsung 990 SSD, EVGA 1000P2 PSU, 12.9" iPad Pro Thrustmaster TCA Boeing Yoke, TCA Airbus Sidestick, Twin TCA Airbus Throttle quads, PFC Cirrus Pedals, Coolermaster HAF932 case Sys2 (P3Dv5/v4): i9-13900KS, water 2x360mm, ASUS Z790 Hero, 32GB GSkill 7800MHz CAS36, ASUS RTX4090 Samsung 55" JS8500 4K TV@60Hz, 3x 2TB WD SN850X 1x 4TB Crucial P3 M.2 NVME SSD, EVGA 1600T2 PSU Fiber link to Yamaha RX-V467 Home Theater Receiver, Polk/Klipsch 6" bookshelf speakers, Polk 12" subwoofer, 12.9" iPad Pro PFC yoke/throttle quad/pedals with custom Hall sensor retrofit, Thermaltake View 71 case, Stream Deck XL button box Sys3 (DCS/P3Dv4/ATS/ETS): AMD 7800X3D, MSI MPG X870E Carbon, Noctua NH-D15S, 64GB GSkill 6000/30, EVGA RTX3090 Alienware AW3420DW 34" 21:9 GSync, Corsair HX1000i PSU, 4TB Crucial T705 PCIe5 + 2TB Samsung 970Evo Plus, TM TCA Officer Pack, Saitek combat pedals, TM Warthog, TM RS300 FF wheel/pedals, Coolermaster HAF XB case
November 15, 201411 yr Author Update: The problem seems to be with the TCAS files. I went back to the latest archived folder I have that included the ILH_TCAS.gau file and I put it in the gauges folder. No difference, I get the Unable To Load Gauge warning when I try to load the Tinmouse. Then I noticed that there was no TCAS.dll file in the Modules folder. So I put TCAS2v7.dll and TCAS2v7.ini in the modules folder. Result: when starting FS2004 I get a warning about these 2 files. When these 3 files are removed the Tinmouse loads and works normally, except of course that there's no TCAS. I'm stumped, anyone have any ideas?
November 16, 201411 yr The TCAS2v7.dll and the ini file both go into the FS9 \Gauges folder, not the \modules folder. Also, make sure the ISG1 TCAS Logic gauge is not active in the panel.cfg, as it is incompatible with Lee Hetherington's TCAS gauge. The ILH TCAS gauge uses FSUIPC...might be an issue has popped up there. You could try saving your fsuipc.ini file in the modules folder and let it build a new one and see if that works. Also, check that your FSUIPC is registered. Regards Bob Scott | President and CEO, AVSIM Inc ATP Gulfstream II-III-IV-V Sys1 (MSFS20+24/XPlane12+11): AMD 9800X3D, water 2x240mm, MSI MPG X670E Carbon, 64GB GSkill 6000/30, nVidia RTX4090FE Alienware AW3821DW 38" 21:9 GSync, 2x4TB Crucial T705 PCIe5 + 2x2TB Samsung 990 SSD, EVGA 1000P2 PSU, 12.9" iPad Pro Thrustmaster TCA Boeing Yoke, TCA Airbus Sidestick, Twin TCA Airbus Throttle quads, PFC Cirrus Pedals, Coolermaster HAF932 case Sys2 (P3Dv5/v4): i9-13900KS, water 2x360mm, ASUS Z790 Hero, 32GB GSkill 7800MHz CAS36, ASUS RTX4090 Samsung 55" JS8500 4K TV@60Hz, 3x 2TB WD SN850X 1x 4TB Crucial P3 M.2 NVME SSD, EVGA 1600T2 PSU Fiber link to Yamaha RX-V467 Home Theater Receiver, Polk/Klipsch 6" bookshelf speakers, Polk 12" subwoofer, 12.9" iPad Pro PFC yoke/throttle quad/pedals with custom Hall sensor retrofit, Thermaltake View 71 case, Stream Deck XL button box Sys3 (DCS/P3Dv4/ATS/ETS): AMD 7800X3D, MSI MPG X870E Carbon, Noctua NH-D15S, 64GB GSkill 6000/30, EVGA RTX3090 Alienware AW3420DW 34" 21:9 GSync, Corsair HX1000i PSU, 4TB Crucial T705 PCIe5 + 2TB Samsung 970Evo Plus, TM TCA Officer Pack, Saitek combat pedals, TM Warthog, TM RS300 FF wheel/pedals, Coolermaster HAF XB case
November 16, 201411 yr Author Thanks for your response Bob. I did everything you suggested but still no dice! I put the TCAS2v7.dll and .ini files into the gauges folder, checked through the panel.cfg file and ISG1 TCAS does not appear anywhere there. Finally, I removed the fsuipc.ini file from the modules folder and let it build a new one but the warning appears just the same. My FSUIPC is definitely registered.
November 15, 201510 yr Author Finally solved my problem. It turned out to be a problem with FSUIPC. Got it sorted out and TCAS is working again!
Create an account or sign in to comment