Jump to content

Sign in to follow this  
qqwertzde

Speedbrake won't disengage

Recommended Posts

I have tried to assign an axis to the speedbrake lever in the P3D control settings, but the lever behaves very erratically. It is going up and back down when I move the axis (Saitek throttle quadrant) from one end to the other, and it is impossible to fully move it to the down version.

 

I also tried to disable the axis and use the keyboard command "/" to move the lever, but even then I cannot fully move it to the down position. Only if I scroll the middle mouse wheel for a couple of seconds it finally moves into the correct position, and only with the axis disabled.

 

I am only doing this because FSUIPC is not working with this plane. With all other planes the throttle quadrant works flawlessly.

On a related note, the flaps only move from up to full when I move the respective axis. I have to use buttons to get them to work properly.

 

Peter Marlin


(P3D v4, i7-3820CPU @ 3.6 GHz, GTX 1070, 16 GB ram)

Share this post


Link to post
Share on other sites

I have tried to assign an axis to the speedbrake lever in the P3D control settings, but the lever behaves very erratically. It is going up and back down when I move the axis (Saitek throttle quadrant) from one end to the other, and it is impossible to fully move it to the down version.

 

I also tried to disable the axis and use the keyboard command "/" to move the lever, but even then I cannot fully move it to the down position. Only if I scroll the middle mouse wheel for a couple of seconds it finally moves into the correct position, and only with the axis disabled.

 

I am only doing this because FSUIPC is not working with this plane. With all other planes the throttle quadrant works flawlessly.

On a related note, the flaps only move from up to full when I move the respective axis. I have to use buttons to get them to work properly.

 

Peter Marlin

FYI

I too have the Saitek combos, yoke, quadrant and rudders. I have assigned the Red leveler to airbrake and it works with NO problem at all. Set in FSX:SE and ticked Reverse.

From leveler full up to all way down. I also Arm it on approach by moving a little bit down.

 

FSX:SE Win7 64


Per W Sweden

 

Boeing777_Banner_Pilot.jpg

Share this post


Link to post
Share on other sites

Hello Per,

 

thanks a lot for your help. After a couple of restarts I got it to work. 

 

Peter


(P3D v4, i7-3820CPU @ 3.6 GHz, GTX 1070, 16 GB ram)

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
  • Donation Goals

    AVSIM's 2020 Fundraising Goal

    Donate to our annual general fundraising goal. This donation keeps our doors open and providing you service 24 x 7 x 365. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. We reset this goal every new year for the following year's goal.


    18%
    $4,640.00 of $25,000.00 Donate Now
×
×
  • Create New...