December 28, 20205 yr Hello All, Just wondered if anyone else had experienced this issue and found a solution: Thought i'd try out Envshade but after installing and updating with patch to 1.1.6.0 when I launch P3D I get the dreaded 'DXGI Device Hung' message at 90% loaded/processing shaders stage. However if I disable HDR in P3D the issue goes away. This is with P3D 5.1 & Gigabyte RX5700 XT graphics. Prior to this I had no problems getting decent performance out of of P3D with all the usual addons. As I have a bit of time on my hands i've tried various things: clean install of video drivers, clean install of P3D, all imaginable combinations of graphics settings, even fiddling with Tdr settings in the registry etc. but to no avail. Not the end of the world just not to bother with Envshade, just annoying me that I can't make it work! 😄(I've checked the envshade forum which is where I picked up on switching off HDR, but otherwise no joy). Edited December 28, 20205 yr by lordonion
December 28, 20205 yr Here I use EnvShade on both view pc’s without any issues. You could un- reinstall P3D Client and start with a clean shader setup. 5950x3d 5.4-5.7 GHz - Asus ROG 870 Crosshair Apex - GSkill Neo 2x 24 Gb 6000 mhz / cas 26 - MSI RTX 5090 Gaming Trio OC - 1x SSD M2 6000 2TB - 1x SSD M2 2800/1800 1Tb - Corsair 5400 case - Corsair 360 liquid cooling set - 3x 75’ TCL tv. 13600 6 cores @ 5.1 GHz / 8 cores @ 4.0 GHz (hypterthreading on) - Asus ROG Strix Gaming D - GSkill Trident 4x Gb 3200 MHz cas 15 - Asus TUF RTX 4080 16 Gb - 1x SSD M2 2800/1800 2TB - 2x Sata 600 SSD 500 Mb - Corsair D4000 Airflow case - NXT Krajen Z63 AIO liquide cooling - FOV : 200 degrees My flightsim vids : https://www.youtube.com/user/fswidesim/videos?shelf_id=0&sort=dd&view=0
December 28, 20205 yr Author Thanks for the suggestion Gerard! I can get P3D working again with a clean shader setup, but unfortunately always fails if I reinstall EnvShade.
December 28, 20205 yr That’s weird. EnvShade has 2 presets : performance and quality. Try performance to see if that makes a difference. Start EnvShade as Admin. 5950x3d 5.4-5.7 GHz - Asus ROG 870 Crosshair Apex - GSkill Neo 2x 24 Gb 6000 mhz / cas 26 - MSI RTX 5090 Gaming Trio OC - 1x SSD M2 6000 2TB - 1x SSD M2 2800/1800 1Tb - Corsair 5400 case - Corsair 360 liquid cooling set - 3x 75’ TCL tv. 13600 6 cores @ 5.1 GHz / 8 cores @ 4.0 GHz (hypterthreading on) - Asus ROG Strix Gaming D - GSkill Trident 4x Gb 3200 MHz cas 15 - Asus TUF RTX 4080 16 Gb - 1x SSD M2 2800/1800 2TB - 2x Sata 600 SSD 500 Mb - Corsair D4000 Airflow case - NXT Krajen Z63 AIO liquide cooling - FOV : 200 degrees My flightsim vids : https://www.youtube.com/user/fswidesim/videos?shelf_id=0&sort=dd&view=0
December 28, 20205 yr Author 4 minutes ago, GSalden said: That’s weird. EnvShade has 2 presets : performance and quality. Try performance to see if that makes a difference. Start EnvShade as Admin. Indeed it is weird! I have tried all combinations of settings in envshade - performance / quality, low/high sliders, etc. Run and install as admin, but always the same hung graphics card unless I disable HDR in P3D. Wondering if it might be something graphics card/driver specific, as the only other post I found with this issue (unresolved) was with the RX5700.
December 28, 20205 yr 2 hours ago, lordonion said: Indeed it is weird! I have tried all combinations of settings in envshade - performance / quality, low/high sliders, etc. Run and install as admin, but always the same hung graphics card unless I disable HDR in P3D. Wondering if it might be something graphics card/driver specific, as the only other post I found with this issue (unresolved) was with the RX5700. Asking the most basic question, but is your EnvShade up to date for 5.1? Daniel M i9-12900K, 32GB DDR5 RAM, PNY RTX 3090, Custom Watercooling
December 28, 20205 yr Author I believe so! Downloaded the base package from sim market and then applied the patch to version 1.1.6.0
December 29, 20205 yr 6 hours ago, lordonion said: I believe so! Downloaded the base package from sim market and then applied the patch to version 1.1.6.0 If you haven't already, try running EnvUpdater just to make sure. Daniel M i9-12900K, 32GB DDR5 RAM, PNY RTX 3090, Custom Watercooling
December 29, 20205 yr Author Hello all, thanks for suggestions. I've heard back from the Toga Projects team now that envshade isn't working correctly for some AMD cards and there isn't currently a solution. At least I know it isn't just me now!
Archived
This topic is now archived and is closed to further replies.