Hi

As the subject. Does anyone has Sismo Boards?

I have a few technical questions regarding what components I can connect into it?

Best regards Fredrik

Hi  Fredrik,

I use SISMO boards.  While they are easiest to use with SISMO components, each board has a diagram, available at the SISMO site, which shows how to connect inputs/outputs, etc.

 

Best,

Jim

 

Edited June 29, 20214 yr by Jim Harnes
grammer

Hi

Glad to have your contact. You can start with writing your knowledge in Sismo board and Prosim737 😊

I building a FSPanel which are based on B737NG / Max. I have plan to use the Arduino Mega R3 with Mobiflight + FSUIPC. My plan for the FSPanel has partly change with the purchase of Prosim 737 in a good way. I have already bought all of the components based on Mobiflight.

My components 🙂

I have look at the Sismo boards during a long period, I find it much more expensive solutions but the most important is the stability and the simplicity of configuration ...

I also have some question bellov (Correct if I have an incorrect idea of something). All outputs component are 5V and 20mAp. My components are as follows:
• Switches – on/off | on /off / on | mom/ off/ mom and Rotary Switches – 12 pos (Switches, Buttons. Rotary Switches.jpg)

Does it work to connect --> https://eckstein-shop.de/V-TEC-Jumper-W ... sortment_1 into the SC-MB directly with 2,54 it´s housing --> https://eckstein-shop.de/254mm-Crimp-Co ... n-5-Pack_1 instead of the GIC V4.0 board but It seems much easier using a such board as it has screw terminals? 

I have seen the WIRING SCHEDULE in sismos pdf of it´s (SimCards Ethernet - User Manual (Features) à 5.5.1). You have a common gnd. Ex. The all components in pin 1-8 must be connect and share the GND from Pin = 10?
What if you need 12 pins (1-8 and 11-14). Can you connect all the gnd in a common wire (pin = 10,20,30 and 40) or must the group of pin 1-8 have the gnd in pin 10 separately from the others gnd pin 20,30 and 40. I think I have the answer in “All the grounds are common.” 

4) Any advantage splitting the gnd in group of 8 dp?

• Rotary Encorder (Rotary Encorder.jpg). The component is require 5V and have one pin for 5V one for gnd and 2 signal pins:

1) If I have correct in nr 2 above the components will take 2 pins, one for gnd and one for 5V.

2) Are the 5V pin also common across the connection (The flat cable in 40 pins)?

 

• LED – Displays like above as “LED – Display in panel ….(Modell HD44780 and drives by a 12C module)

1. Does this type of display work?
   1. I can use Mobi… for them!

• LED – segments (Max 7219) (https://www.banggood.com/sv/5Pcs-MAX721 ... 14QAvD_BwE).

1. Does this type of segment work?

 • LED-Lights (LED – Light in panel.jpg) Incl its own resistor at I think 10 Ohm (https://www.ebay.com/itm/5mm-5V-6V-7V-D ... 2749.l2649).

1) Does this type of led work?

2) Does the board have some kind of pwm feature for led-light, mine are way to bright in full power?

Does the solution with Prosim737 and Sismo boards supports Auto detection of the components poss. ex. A physical switch is in the ON poss. and if the corresponding switch in FS is in the opposite poss. will the switch in FS auto change its poss… at ex. the startup?

Take care//
Best regards Fredrik Hjärpe